How we prove a niacinamide lot is niacinamide
Identity for niacinamide is four answers, not one assay: the document (name, CAS number and lot on the certificate); the IR spectrum, which shows the amide and pyridine functional groups against a reference; the HPLC result, which gives the assay and separates nicotinic acid; and the physical set of pH 5.5–7.5 at 10%, melting 128–131 °C, loss on drying ≤0.5% and residue on ignition ≤0.1%. A certificate that reports only the assay has answered the third question and left the other three open.
A 99% assay says the peak is there; the IR, the melting range and the nicotinic acid figure say the peak is niacinamide.
The four layers
| Layer | Test | What it proves | What it misses |
|---|---|---|---|
| Document | Name, CAS, lot and COA | The chain from pack to paper | Whether the powder is the named material |
| Spectroscopic | IR against a reference; UV maximum near 261 nm | The amide and pyridine functional groups | The amount present; trace impurities |
| Chromatographic | HPLC assay and nicotinic acid | The amount and the hydrolysis impurity | The functional groups; a co-eluting unknown |
| Physical | pH, melting, LOD, ROI | The solid's behaviour and the water/inorganic load | Specific identity on its own |
The document layer is necessary but not sufficient. A certificate can be correct and still belong to a different drum, so the lot code on the certificate, the pack and the retained sample has to match. The spectroscopic layer is the most direct evidence of the molecule: IR shows the amide carbonyl and the pyridine ring, and the comparison is against a reference spectrum. The chromatographic layer is the most direct evidence of amount and impurity. The physical layer catches substitutions the first three can miss.
The assay ratio and the impurity ratio
An HPLC assay is a ratio: the response of the sample peak divided by the response of a reference standard of known purity, corrected for the sample weight and the dilution. The result is only as good as the standard, the integration and the basis. A figure calculated on the dried substance and a figure calculated as-is are not the same number, and a 99.0–101.0% window includes method uncertainty. A result of 100.4% is not a material that is 100.4% pure; it is a comparison that sits slightly above the standard's assigned value.
The impurity ratio is separate. Nicotinic acid is measured against a standard or by area normalisation, and the certificate should say which; the 10 ppm limit is close enough to the practical floor of HPLC-UV that the method's limit of quantification has to be stated. A certificate that says “nicotinic acid: not detected” without naming the limit has told you about the method, not the lot. The same logic applies to the difference between the assay and 100%: that difference is not all impurity, and it is not a purity statement.
What X-ray diffraction adds
X-ray diffraction identifies a crystalline phase from its diffraction pattern. For niacinamide it confirms that the solid is crystalline, and it can show a second crystalline phase such as niacin. It is not a trace method: a 10 ppm nicotinic acid limit is an HPLC question, not an XRD question. If a supplier claims a specific crystal form, ask for the pattern and the reference; if the claim is only “crystalline powder,” the IR, the melting range and the assay are the routine evidence.
XRD is most useful when the solid form matters to the process — compaction, dissolution or blend behaviour — or when a spectroscopic identity check is disputed. It does not replace the assay, the impurity method or the pH and melting tests. A laboratory report should state the detection limit for the second phase, because a “not detected” line without a limit is not evidence about the sample.
Three ways a lot stops being niacinamide
The first route is niacin. Nicotinic acid is the acid analogue, it is UV-active, and a blend can be tuned to an assay window. The tells are a pH below the 5.5–7.5 window, a melting range that is low and broad or shows a second melt near 236–239 °C, and an IR spectrum with a carboxylic acid carbonyl rather than an amide. The second route is a nicotinate salt, such as sodium nicotinate. The pH moves alkaline, the residue on ignition rises, and the label may not name the salt. The third route is dilution: dextrose, lactose, maltodextrin, starch or an inorganic carrier. The assay falls, the loss on drying or the residue on ignition rises, and the IR shows bands that do not belong to niacinamide.
| Route | What moves | Test that shows it |
|---|---|---|
| Niacin substitution | pH down; melting low or broad; IR acid carbonyl | pH, melting, IR, HPLC |
| Nicotinate salt | pH up; residue on ignition up | pH, ROI, metal panel |
| Dilution | Assay down; LOD or ROI up; extra IR bands | Assay, LOD, ROI, IR |
A fourth problem is not a substitution but a documentation failure: a relabelled lot. The powder can be correct and the certificate can belong to another batch. The lot code on the pack, the certificate and the retained sample is the only defence, and it is the first thing to check when a result is disputed.
How to write the specification
- “Niacinamide, crystalline; CAS 98-92-0; assay 99.0–101.0% by HPLC, calculated on the dried substance.”
- “Identification: IR conforms to the reference spectrum.”
- “pH 5.5–7.5 on a 10% solution.”
- “Melting range 128–131 °C.”
- “Loss on drying ≤0.5%; residue on ignition ≤0.1%.”
- “Nicotinic acid ≤10 ppm by HPLC, with the limit of quantification stated.”
- “Heavy metals Pb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg; microbiology APC ≤1,000 cfu/g, yeast and mould ≤100 cfu/g, E. coli and Salmonella absent.”
The list is longer than an assay line because identity is not one measurement. A specification that names the IR, the pH, the melting range and the nicotinic acid limit gives a laboratory something to reject against; a specification that names only the assay leaves the other three layers to the supplier's judgement.
Five questions for a supplier
- Which IR reference and library did the identification use, and can you send the spectrum for this lot?
- What is the HPLC method for the assay and for nicotinic acid, and what is the limit of quantification at the 10 ppm limit?
- What are the pH and melting range on this lot, and at what concentration and heating rate were they measured?
- Is the assay calculated on the dried substance or as-is, and what are the loss on drying and residue on ignition?
- Is the material 100% niacinamide, or is it blended with niacin, a nicotinate salt or a carrier? If it is a blend, what is the composition?
The niacinamide hub carries the catalog specification; the COA page shows where these figures sit; the grade page compares the two vitamin B3 forms; the FTIR method note and the HPLC method note explain the two central tests. The quality page covers the release workflow.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation