Quality system
Quality is a documentation practice.
A specification is a promise; a certificate is the evidence that the promise was kept for one lot. This page describes the three gates between the material and the drum, the panel that is measured, and the claims the file does not support.
Release discipline
Three gates between material and drum.
Every gate leaves a document. If a gate has no document, it did not happen.
Specification
The property has to be written before the lot is made: form, hydrate state, elemental assay range, ligand ratio, moisture, particle size and the contaminant panel. A parameter that is not in the specification is not tested at release.
Sampling and testing
The sample is drawn from the lot, not from a sample cabinet. The laboratory tests against the agreed method, and the report names the method beside each result. Third-party testing is used where the buyer's review or the destination market requires it.
Release
The lot is released only when every parameter is inside its limit, the COA is signed and the document pack is complete. A result outside the range is either rejected or reworked and re-tested; it is not averaged into a pass.
Analytical panel
What gets measured.
The panel is agreed in the quotation, not chosen after the lot is made. The method is named beside every result; a result without a method cannot be compared with another supplier's.
| Panel | Parameters |
|---|---|
| Identity and assay | Magnesium by complexometric titration (EDTA) or ICP-OES · Glycine content by HPLC, and the calculated Mg : glycine molar ratio · Free glycine, to show unreacted ligand · XRD screen for crystalline magnesium oxide in chelated grades |
| Physical and process | Appearance, colour and odour · Loss on drying and hydrate form · pH of a 5% suspension · Particle size distribution and bulk density |
| Contaminants | Lead, arsenic, cadmium and mercury by ICP-MS · Microbiology: APC, yeast and mould, E. coli, Salmonella · Residual solvents matched to the crystallisation system · Foreign matter and acid-insoluble residue |
Method transparency
- The certificate names the method for every result, including the ligand and the hydrate state.
- A “not detected” result carries the detection limit of the method.
- A calculated figure, such as the Mg : glycine ratio, names the two assays it comes from.
- Third-party reports are issued on the same sample as the supplier's certificate where possible.
Document pack
Six files, one lot number.
Each file answers a different review. A COA is not a TDS, and neither one replaces an allergen statement.
Certificate of analysis
Batch-specific results for identity, magnesium assay, glycine content, moisture, pH, particle size, heavy metals and microbiology, with the method named against each parameter.
Technical data sheet
Chemical form, hydrate state, CAS number, specification ranges, solubility, bulk density, recommended storage and the grades available for the same ingredient.
Safety data sheet
A 16-section SDS issued against the exact grade supplied, in the format your EHS team already files.
Allergen, GMO and origin statements
Declarations covering the major allergen list, gluten, animal-derived inputs, GMO status and the manufacturing site, signed for the batch.
Residual solvent and contaminant statements
The solvent system used in crystallisation, plus heavy-metal and microbiological results against the destination-market limits.
Specification comparison
A line-by-line comparison of our specification against the one you sent, including where we cannot match and why.
Certificates
Facility-level, never implied.
Facility certificates listed above are confirmed in scope and validity with each quotation. Product-level coverage is never implied, and a certificate is never described as an approval of the ingredient.
What an ingredient file does not prove
It does not prove that a finished product is safe, effective or compliant in a destination market. It does not replace the brand's regulatory review, its label review or its claim substantiation. It does not turn a facility certificate into a product certificate. It does not promise a therapeutic outcome, and it does not authorise a disease claim.
What it does is describe the material and the batch: form, assay, method, limit, result and the documents that travel with the lot. That is the boundary of what this site writes. Read the editorial policy.
Questions
Before you ask for the file
Which documents ship with a lot?
A batch-specific COA, TDS, SDS, allergen and GMO statements, an origin record and a residual-solvent statement. Third-party heavy-metal or microbiological reports can be added where the buyer's review requires them.
Are the certificates product certifications?
No. They are facility-level certificates held by the legal entity, and their scope and validity are confirmed with each quotation. Product-level coverage is never implied, and a certificate is never described as an approval of the ingredient.
What is the difference between a specimen COA and a batch COA?
A specimen shows the format: parameter, method, limit and the place where a result would be printed. A batch COA carries the lot number and the result for that lot, and is signed against the specification agreed in the quotation.
How long are samples and records kept?
A retained sample is kept from each released lot so a later question can be checked against the same material. The retention period is agreed in the supplier qualification file and stated in the TDS.
When is third-party testing worth ordering?
On a first shipment from a new source, when a label claim depends on a form the supplier's certificate does not prove, or when the destination market requires an outside report. The useful panel answers the open question; it is not a full repeat of the supplier's certificate.
Next step
Ask for the documents before the price.
Tell us the ingredient, the grade and the destination market. We will send the specification, a sample COA and the document list we can support for that lot.