HPLC for mineral ingredients
HPLC separates glycine from the rest of the sample and measures it, either after derivatisation or as part of an amino acid profile. Run on an unhydrolysed extract it gives free glycine; run after acid hydrolysis it gives total glycine. The difference is the only chromatographic handle on how much ligand is bound.
In short
The separation method that measures glycine and, run before and after hydrolysis, how much of it is free.
How the measurement is made
Glycine has no useful ultraviolet chromophore, so most methods derivatise it before separation: ortho-phthalaldehyde with a thiol, dansyl chloride or phenyl isothiocyanate, followed by reverse-phase separation and ultraviolet or fluorescence detection. An amino acid analyser with ion-exchange separation and ninhydrin detection is the classical alternative. Whichever route is used, the derivative has to be stable over the run and the reaction conditions have to be fixed.
Two preparations answer two different questions. An aqueous extract injected directly gives free glycine, the ligand that is not bound to magnesium. A separate portion hydrolysed in hydrochloric acid at about 110 °C releases the bound ligand, and the resulting figure is total glycine, with bound glycine taken as the difference. The hydrolysis step needs an internal standard such as norleucine, because glycine is lost and diluted in ways that a single external standard cannot correct.
System suitability, resolution between glycine and the neighbouring amino acids, peak symmetry, a calibration curve and duplicate injections are the routine controls. Retention time against a certified standard is the identification criterion, and a spiked sample confirms that the peak is glycine rather than a co-eluting matrix component. The result is reported as a percentage of the sample, on the same moisture basis as the magnesium assay.
What the result proves
The assay measures glycine content and, with the two preparations, separates the free fraction from the bound fraction. That separation is the useful part: a material with the expected total glycine but an unusually high free glycine contains ligand that is not attached to the metal. A fully reacted chelate should show a small free-glycine figure, and a blend with added glycine often does not.
With the magnesium result, the total glycine figure produces the Mg : glycine molar ratio. The theoretical ratio for the 1:2 chelate is 2.00, and a ratio far from that value points to a hydrate, an excess of ligand or a blend. The ratio is a calculated quantity, and it is only as good as the two assays that feed it.
The chromatogram also shows the amino acid profile of the raw material, so a glycine supplied as a fermentation or synthetic grade can be checked for other amino acids at the method's resolution. That is an impurity check, not an identity proof. Identity still rests on the standard, the retention time and the other methods in the file.
What it cannot tell you
A single injection cannot say whether glycine is free or bound, and a hydrolysed injection cannot say what the original species was, because hydrolysis destroys the chelate. The free and total runs answer the question only when they are read together. A certificate showing one glycine number without stating which preparation it came from is ambiguous.
The method cannot distinguish a fully reacted chelate from a physical blend of a magnesium salt and glycine at the same ratio, because both release the same glycine on hydrolysis. A blend can be built to pass the ratio, the free-glycine limit and the magnesium assay at the same time. Chromatography separates compounds; it does not establish coordination.
Glycine is small and polar, so retention is weak unless it is derivatised or ion-paired, and co-elution with other small amino acids is a real risk. Hydrolysis losses, incomplete release and derivative instability all bias the total downward. None of these effects is visible in a ratio that is reported to two decimal places.
What it proves
- Glycine content of the sample, measured against a certified standard.
- Free glycine, from an extract that has not been hydrolysed.
- Total glycine after acid hydrolysis, and therefore bound glycine by difference.
- The glycine input to the Mg : glycine molar ratio.
What it does not prove
- Whether a single glycine figure represents free or bound ligand, without the paired preparation.
- Coordination or the identity of the magnesium compound.
- A physical blend built to the same magnesium and glycine figures.
- Trace contaminants, residual solvents or microbiological quality.
What to ask the laboratory
- Was the sample hydrolysed, and what does each glycine figure represent?
- How is glycine derivatised, and what detection wavelength or fluorescence setting is used?
- Which internal standard was added before hydrolysis, and what recovery was obtained?
- What is the resolution from the nearest amino acid, and was a spiked sample run?
Read the two glycine figures and the preparation they came from, then look at the ratio. Total glycine without a free-glycine figure hides unreacted ligand, and free glycine without a total figure cannot be interpreted. A ratio near 2.00 is consistent with the 1:2 chelate but does not prove it, because a blend can be formulated to the same ratio; the chromatogram has to be read with magnesium, XRD and FTIR.
Where the method is used
- Magnesium Bisglycinate — 1:2 magnesium–glycine chelate, anhydrous basis.
Sources
The method pages sit behind the COA page. The terms used here are defined in the buyer glossary, and the regulatory limits are on the compliance page.
Related documents
Send the certificate or specification you are reviewing and we will name the method behind each figure.
Request a specification review