06 Identity & adulteration

How we prove a 5-MTHF lot is the calcium salt

Technical document 06 · Reviewed 2026-11-19 · 5-MTHF

On this page
  1. Four measurements that must agree
  2. The calcium ratio and the isomer ratio
  3. What XRD adds, and what it does not
  4. How a substitution shows up
  5. Writing identity into the specification
  6. Five questions to put in writing

A 5-MTHF lot is the calcium salt when four lines agree: the document names calcium L-5-methyltetrahydrofolate and CAS 151533-22-1, HPLC retention and UV match the reference, calcium is close to the theoretical 8.06%, and the water and assay reconcile the mass balance. The assay alone cannot separate the salt from the free acid, the glucosamine salt or a dilution. The calcium figure and the isomer ratio are the checks that do.

In one line

Identity is four agreeing measurements: the document names the salt, HPLC and UV identify the folate, calcium confirms the counter-ion and the water closes the mass balance.

Four measurements that must agree

A certificate may carry the right name and still fail to prove it. The layers below are separate questions, and each one needs its own evidence; an answer to the first alone describes a document, not a drum.

Four layers of 5-MTHF calcium identity
LayerQuestionTestWhat it proves
Label and COADoes the paperwork name calcium L-5-MTHF?Product name, CAS number and salt ratioDocument completeness
ChromatographyIs the peak the 5-methyl folate?HPLC retention plus UV spectrumThe folate nucleus
Counter-ionIs calcium the counter-ion?Calcium by ICP-OES, about 8.06%The 1:1 salt
Stereochemistry and balanceIs it the (6S) form, and is it diluted?(6S)/(6R) ratio, water, assayGrade and mass balance

The calcium ratio and the isomer ratio

The calcium salt is a 1:1 salt. The anhydrous molecular weight is 497.52, of which 40.08 is calcium, so the theoretical calcium content is 8.06%. A result close to that figure, with a 95–101% assay, is consistent with the calcium salt. A low figure points to the free acid, the glucosamine salt or a dilution; a high figure points to another calcium salt or a calcium-containing carrier. Calcium by ICP-OES is the direct test, and the pH of a 1% solution is a supporting check rather than a quantitative one.

The isomer ratio answers a different question. 5-MTHF has a chiral centre at C6, and the naturally occurring (6S) form and the (6R) form are diastereomers with the same mass and the same calcium content. The calcium figure cannot see the difference. Only a method that resolves the two forms can report the ratio, and the certificate should state the (6S) content or the (6S)/(6R) ratio when the grade is sold on the natural isomer. A powder that passes the assay and the calcium check can still carry more of the (6R) form than the specification intended.

The two ratios together are stronger than either alone. A low calcium figure with a normal assay suggests a non-calcium salt or a dilution; a normal calcium figure with a poor isomer ratio suggests the right salt made with the wrong stereochemistry. Ask for both when the source or the process is new.

What XRD adds, and what it does not

XRD addresses a separate issue: what solid form is present, and does its pattern agree with a reference? It separates a crystalline salt from an amorphous solid, compares the hydrate form of two sources and shows when a lot has changed solid form after drying or milling. It is not a purity assay, and it does not measure the counter-ion or the isomer ratio.

Before accepting a “match” statement, request the reference pattern and the detection limit. A report that says only “XRD conforms” without the pattern has added little. XRD earns its place when solid form is the question, when two suppliers claim the same grade, or when a lot behaves differently in a blend than its certificate suggests. When a lot is disputed, the solid-state pattern, the calcium figure, the HPLC/UV data and the isomer ratio reinforce one another.

How a substitution shows up

Common 5-MTHF substitutions and the signals
AdulterantWhat it doesSignalTest
Folic acidFully oxidised; no methyl group and no calciumDifferent retention; calcium lowHPLC/UV, calcium
Calcium folinateA different reduced folate, the 5-formyl formDifferent retention; calcium normalHPLC/UV with a resolving method
Glucosamine saltA different counter-ion and a different massCalcium low; label name wrongCalcium by ICP-OES, HPLC
(6R) diastereomerSame mass and same calcium, wrong configurationIsomer ratio shiftsHPLC that resolves the two forms
DilutionLowers the folate per gramAssay low; calcium lowMass balance, calcium
MoistureRaises water and lowers the as-is assayWater high; anhydrous assay normalKarl Fischer

Colour is the weakest signal. White to off-white is a wide range, and a yellow or brown cast is more likely to mean oxidation or light exposure than a deliberate substitution. The strong signals are the retention and the UV spectrum, the calcium figure, the isomer ratio and the mass balance. A certificate that gives colour and a percentage but no identity evidence has left the most likely substitution untested.

Writing identity into the specification

  • “Calcium L-5-methyltetrahydrofolate, CAS 151533-22-1, C₂₀H₂₃CaN₇O₆·xH₂O, calcium salt (1:1).”
  • “Assay 95.0–101.0% by HPLC, with the basis stated; water ≤5.0% by Karl Fischer.”
  • “Identification by HPLC retention and UV spectrum against a reference standard.”
  • “Calcium about 8.06% on the anhydrous basis, by ICP-OES, where the form is to be confirmed.”
  • “Diastereomer ratio: state the (6S) content or the (6S)/(6R) ratio.”
  • “No folic acid or other folate above the stated limit, by a method that resolves the forms.”
  • “Particle size ≥95% through 40 mesh with the sieve method named; contaminant and microbiological limits as tabulated.”

Five questions to put in writing

  1. What salt is in this lot, and what CAS number does the certificate carry?
  2. Will you release the chromatogram and the UV spectrum, not just the assay figure?
  3. What calcium result did ICP-OES give, and by which method?
  4. What is the (6S)/(6R) ratio for this lot, and which method resolved it?
  5. Would you agree to a joint re-test of the retained sample if the lot were contested?

Written answers to all five give a buyer something to audit; an assay percentage alone gives a number. Catalog values are listed on the product hub; the COA page explains where each figure belongs on the certificate; the grades page explains the salt and isomer choices; the methods index covers the assay families, and the HPLC and XRD notes describe the separations; the quality page covers release and the retained sample.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation