What the COA for zinc oxide actually contains
A certificate for a zinc oxide lot reports appearance, identification by IR and complexometric titration, the oxide assay at ≥99.0%, elemental zinc at 78.0–80.0%, loss on drying below 0.5%, lead and the other heavy metals per element, microbiology and particle size. The assay and the zinc figure describe the same powder from two directions, so they have to share one basis. The lead result and the particle-size result are what separate a supplement grade from a technical one.
Two numbers describe the same powder — the oxide assay and the elemental zinc — so the certificate has to fix the basis of both before the lead figure decides the grade.
The certificate as a test report
A zinc oxide certificate is short, and each line should still carry the parameter, the method and the release limit. There is no ligand or hydrate to prove; the risk is a grade that was never intended for food or supplement use, or a purity figure copied without its method.
The identity row is a pair of tests. IR confirms the Zn–O lattice and shows whether a carbonate or a hydroxide has formed; the titration confirms the zinc proportion. Neither is a purity figure on its own.
| Parameter | Method | Release limit |
|---|---|---|
| Appearance | Visual | White powder |
| Identification | IR and complexometric titration | Conforms to the reference |
| Assay (ZnO) | Titration after acid dissolution | ≥99.0% |
| Zinc (Zn) | Complexometric titration | 78.0–80.0% |
| Loss on drying | Gravimetric | ≤0.5% |
| Heavy metals | ICP-MS | Lead, arsenic, cadmium, mercury: ≤3, ≤2, ≤1 and ≤0.1 mg/kg |
| Microbiology | Total plate count and absence tests | Total plate count ≤1,000 cfu/g; yeasts and moulds ≤100 cfu/g; E. coli and Salmonella not detected |
| Particle size | Sieve analysis | ≥95% passing a 40 mesh sieve |
The assay, the zinc figure and the basis
The oxide assay and the elemental zinc are two arithmetic views of one result. Zinc is 65.38 of the 81.38 g/mol of ZnO, so pure oxide is 80.34% zinc and 19.66% oxygen. A 99.0% oxide assay therefore corresponds to about 79.5% zinc, which sits in the middle of the catalog range. When the two numbers disagree by more than that arithmetic allows, one of them is on a different basis or the sample is not the oxide.
The basis has to be named. A result as received, a result on the dried basis and a result on the ignited basis are three different numbers for the same powder once the loss on drying is 0.5%. The oxide holds little water, so the spread is small compared with a hydrate, but the line still has to state its basis.
The assay method also has a preparation step that matters. The oxide is practically insoluble in water, so the sample has to be dissolved in acid before the EDTA titration. A method copied from a soluble zinc salt without that step will under-report, and the under-report looks like a purity problem rather than a preparation problem. Ask whether the acid dissolution is written into the method, and which acid is used.
Release limit versus batch result
A release limit is the boundary the lot was accepted against; a batch result is what the laboratory measured. They belong in separate columns, with the method beside them. A result column that repeats the specification has reported nothing about the lot.
| Parameter | Release limit | Result column |
|---|---|---|
| Assay (ZnO) | ≥99.0% | A measured figure with its basis and the acid-dissolution step |
| Zinc (Zn) | 78.0–80.0% | A measured percentage, consistent with the assay arithmetic |
| Loss on drying | ≤0.5% | A measured percentage |
| Lead | ≤3 mg/kg | A figure in mg/kg with the detection limit |
| Particle size | ≥95% through 40 mesh | The percentage that passed the sieve |
Lead deserves its own line rather than a place in a summed heavy-metals total. A total hides the element that decides the grade, and lead is what most often separates a food or supplement grade from a pigment or technical grade of the same oxide. One summed figure tells the reader less than four per-element results.
What moves between batches
The chemistry of the oxide is fixed; the variation sits in the physical specification and in the trace elements. Particle size, surface area and bulk density move with the milling and the calcination step. Whiteness moves with trace iron and with particle size. Lead moves with the zinc source: an oxide made from refined zinc metal starts lower than one made from an ore concentrate, and the certificate is where that difference has to show.
Loss on drying is usually small, but it is the line that catches a change in the pack or in the store before the assay notices. A rising loss on drying with a falling as-is assay is moisture, not a purity loss. A lot above the 0.5% limit may also be carrying surface carbonate picked up from carbon dioxide and moisture in the air.
Read the trend across lots, not one result at the edge: lead creeping up, the mesh drifting coarser, or a carbonate shoulder in the IR spectrum. The lot code printed on the certificate must also appear on the pouch or drum and on the retain.
When to order an outside test
An outside test is worth ordering in four situations: before a first shipment into a regulated market, when a new source is qualified, when a grade claim is not supported by the certificate, and when a result is disputed. The panel should not be a copy of the certificate. It should be IR for identity, titration after acid dissolution, moisture, ICP-MS for the elements, and a sieve result.
Add XRD when the question is the solid state: it confirms the zincite pattern and shows whether a carbonate or a hydroxide phase is present. Add ICP-OES for calcium, titanium and sulfur when a dilution is suspected, and a water extraction with a sulfate test when a soluble zinc salt may be present.
Require a detection limit beside every screen. A “not detected” line with no limit describes the method, not the sample. The material tested should be the retain, and the report should carry the lot number.
What to compare between two suppliers
Set six lines side by side: grade and intended use, assay and basis, elemental zinc, lead and the other elements, loss on drying, and particle size with the method. A pair of offers that match on assay and disagree on grade or on lead describes two different powders.
Traceability comes next: who made the oxide, from which zinc source, and which milling and packing steps followed. The catalog specification is published on the zinc oxide product page, and the grade detail is on the grades page. The tests that separate the oxide from a carbonate, a sulfate or a dilution are collected on the identity page; the titration is described in the complexometric method note; the release workflow is described on the quality page.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation