06 Identity & adulteration

How we prove a zinc oxide lot is zinc oxide

Technical document 06 · Reviewed 2026-11-19 · Zinc Oxide

On this page
  1. The four identity layers
  2. The zinc-to-oxygen ratio
  3. X-ray diffraction and the solid state
  4. What adulteration looks like
  5. Writing identity into the specification
  6. Five questions to put to a supplier

A zinc oxide lot is zinc oxide when the document, the IR spectrum, the titration and the XRD pattern all agree. The zinc figure alone cannot establish it: a basic carbonate, a soluble zinc salt, a calcium carbonate dilution and a titanium dioxide blend can each be built to sit near a plausible zinc percentage. The mass balance closes the case, because the formula itself fixes the split at 80.34% zinc and 19.66% oxygen.

In one line

Zinc oxide is proved by the lattice and the mass balance: IR and XRD name the solid, and the zinc figure has to agree with the oxygen.

The four identity layers

Each row answers one question. A supplier who stops at the first row has shown paper, not powder.

Four layers of zinc oxide identity
CheckQuestion it answersMethodEvidence it gives
DocumentAre the form and grade named?Name, CAS number, formula, grade statementPaperwork only
SpectroscopyIs the solid an oxide?IR, and XRD where the solid state mattersThe lattice, not the purity
ElementalIs the zinc present in proportion?Acid dissolution and complexometric titrationThe metal content
Mass balanceIs anything else in the drum?Assay, loss on drying, carbonate and sulfate screensConsistency of the numbers

The zinc-to-oxygen ratio

Zinc oxide is 1:1 by formula. Zinc is 65.38 g/mol and oxygen 16.00, which fixes the split at 80.34% zinc and 19.66% oxygen, and every legitimate figure follows that ratio. A 99.0% oxide assay corresponds to about 79.5% zinc. A zinc result of 78.0% beside a 99.0% assay does not follow from the arithmetic, so one of the two figures is on a different basis; a zinc result above 80.5% cannot come from pure oxide at all.

The ratio is a check on the certificate before it is a check on the powder. If the assay and the zinc figure were produced by two methods on two bases, their ratio will not match the formula, and the discrepancy is arithmetic rather than adulteration. Ask for the calculation and the loss on drying before drawing a conclusion.

The same arithmetic catches a blend. An oxide at about 80% zinc can lift a lower-zinc material, and the blend can land inside a range that looks like a single substance. The ratio will not see the second component if it is another zinc salt; the carbonate or sulfate screen will.

X-ray diffraction and the solid state

Zinc oxide crystallises as zincite, a hexagonal wurtzite structure, and its diffraction pattern is distinctive. With copper radiation the strongest reflections sit near 31.8°, 34.4° and 36.3° two-theta, and the peak width gives an estimate of crystallite size. That answers two questions the certificate often leaves open: is the solid crystalline oxide, and is it the same grade as the last lot?

XRD also sees phases that a titration cannot. A basic zinc carbonate shows its own reflections, a hydroxide shows another set, and a titanium dioxide dilution shows rutile or anatase. A pattern that matches zincite plus a second phase describes a different material from one that matches zincite alone, even when both titrate to a similar zinc figure.

XRD is not a routine release test here. Request it when the grade is disputed, when a new source is qualified, or when the powder behaves differently in acid from the previous lot. Before accepting a “match” statement, ask which reference pattern was used and what the detection limit is.

What adulteration looks like

Substitutions for zinc oxide and the signals they leave
AdulterantWhat it doesSignalTest
Basic zinc carbonateDilutes the zinc figure; reacts with acidHigher ignition loss; carbonate band in IR; CO2 on acidIR, XRD, ignition loss
Zinc sulfateWater-soluble; lowers the zinc figureSoluble fraction; sulfate in a water extract; high loss on dryingWater extraction, sulfate test, LOD
Calcium carbonateWhite diluent; lowers the zinc figureCalcium in the elemental scan; effervescence in acidICP-OES, XRD
Titanium dioxideMatches the whiteness; lowers the zinc figureTitanium in the elemental scan; rutile or anatase in XRDICP-OES, XRD
Zinc stearateHydrophobic powder; much lower zincFloats on water; carbon-hydrogen bands in IRIR, water test, titration

Whiteness and fineness are the weakest signals: they are easy to reproduce and say nothing about composition. The stronger signals are the mass balance, the acid reaction, the water-soluble fraction and a method that sees the solid state. Appearance and assay alone leave the most likely substitution untested.

Writing identity into the specification

  • “Zinc oxide (ZnO), CAS 1314-13-2; the grade is named on the certificate.”
  • “Identification by IR and by complexometric titration after acid dissolution.”
  • “Assay ≥99.0% as ZnO; zinc 78.0–80.0% on the dried basis.”
  • “Loss on drying ≤0.5%; no carbonate or hydroxide above the detection limit.”
  • “Lead ≤3 mg/kg; the other elements reported per element.”
  • “Particle size ≥95% through 40 mesh; XRD zincite pattern on request.”

Five questions to put to a supplier

  1. Which grade is this, and which route and zinc source produced it?
  2. Can you provide the IR spectrum and the acid-dissolution method, not only the assay percentage?
  3. What are the zinc and loss-on-drying results for this lot, and on which basis?
  4. Is a sulfate or carbonate screen available, and what is its detection limit?
  5. If a result is disputed, is a joint re-test on the retain acceptable to you?

Those five answers, taken together, make an identity file; one assay line cannot. The product page carries the oxide's specification, and the certificate layout is on the COA page. The grades page explains why the grade belongs to identity, the XRD note covers the detection limit, and the quality page sets out how release is handled.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation