03 Stability

Zinc oxide is stable in the pack; the surface and the matrix are what change

Technical document 03 · Reviewed 2026-11-19 · Zinc Oxide

On this page
  1. The powder in the pack
  2. A slurry is not a solution
  3. What drives change
  4. A stability protocol for the ingredient
  5. The finished formula changes the answer
  6. How the shelf life is set

Dry zinc oxide is chemically stable: it is already the fully oxidised form, it does not hydrolyse in a sealed pack, and its assay does not drift on storage. What changes is the surface and the physics — moisture uptake, reaction with carbon dioxide to a basic carbonate, caking and dust — and, in a formula, the reaction with acids and the photocatalytic effect of the oxide under ultraviolet light. Shelf life is assigned from data for the pack, not from the chemistry of the oxide.

In one line

The oxide does not oxidise or hydrolyse in the pack; moisture, carbon dioxide and an acidic or UV-exposed matrix are what change the result.

The powder in the pack

The ≤0.5% loss-on-drying limit is a release gate, not an allowance for storage. The oxide takes up little water, but a fine powder has a large surface, and an open pouch in a humid room will show a rising loss on drying and a caking tendency before the assay moves at all.

The second reaction is with carbon dioxide. Zinc oxide can form a basic zinc carbonate at the surface when moisture and CO2 are both present, and the product of that reaction does not show in the assay: the zinc figure stays inside the range while the surface chemistry changes. In a formula where the oxide has to react with an acid, a carbonated surface reacts more slowly. Keep the pack sealed and the headspace dry, and read the IR spectrum if a batch behaves differently from the previous one.

Heat is not a risk at normal process temperatures. The oxide is thermally stable well above any drying or tableting condition, and it does not melt or decompose in a dryer. The pack, not the temperature, is the variable unless the process itself is hot and wet at the same time.

A slurry is not a solution

Water does not dissolve the oxide to any useful degree, so a zinc oxide solution is really a suspension. The particles settle, the slurry is mildly alkaline, and the appearance depends on the particle size and on the dispersion step. A clear drink cannot be built on the oxide, and a suspension needs a thickener, a homogenisation step and a stability test that watches for settling rather than for assay loss.

The oxide is amphoteric: dilute acid takes it to the zinc ion, strong alkali takes it to a zincate, and both reactions are open to a formulator. An acidic drink mix can dissolve the oxide when the consumer adds water, but the acid step shifts the pH of the finished product and has to be designed rather than assumed.

In a liquid, light adds a second path. Zinc oxide absorbs ultraviolet light and, under UV, can catalyse reactions in the organic material around it. The oxide itself does not degrade; the matrix can. A clear bottle on a shelf is the case to test, and an opaque pack is the simple control.

What drives change

Factors that change zinc oxide in storage and in a formula
FactorWhat it doesControl
MoistureRaises loss on drying; caking and surface carbonateSealed pouch, dry store, desiccant where needed
Carbon dioxideForms a basic carbonate at the surfaceSealed pack, low headspace, first in first out
AcidDissolves the oxide to a zinc salt; pH movesDesign the acid step; check pH and clarity
AlkaliDissolves to zincate at high pHKeep the matrix away from strong alkali
Ultraviolet lightPhotocatalytic reactions in the matrixOpaque pack; test the matrix in light
Heat in a wet processAccelerates carbonate and acid reactionsCool, dry process; validate the hold
Particle sizeFiner powder reacts and settles fasterFix the mesh and the surface area

The factors combine. A warm, humid store with an open pouch gives moisture and carbonate together, and the formula that follows can behave differently without any line on the certificate moving.

A stability protocol for the ingredient

Long-term storage at 25 °C/60% relative humidity, intermediate storage at 30 °C/65% and accelerated storage at 40 °C/75% cover the warehouse and the transport case. For a food or supplement ingredient the accelerated arm is a stress test rather than a shelf-life claim, and the pack in the trial must be the pack that will be sold.

Test the parameters that can move: loss on drying, IR identity, assay and zinc, particle size, bulk density and, at the end points, the lead result. Appearance and the absence of caking belong in the record too, because they are the changes a customer sees first. A carbonate screen by IR is worth adding when the pack uses paper, board or a liner that is not a moisture barrier.

Run the finished formula separately. A capsule, a tablet, a powder blend and a drink mix each expose the oxide to a different matrix, and the bulk result does not carry across.

The finished formula changes the answer

A dry capsule or tablet has low water activity and the oxide is stable in it. The risks are physical: segregation in a blend, dust in the filling room, and a granulated grade that behaves differently from the milled one. Check content uniformity, not only the bulk assay.

An acidic powder blend is a chemical case. Ascorbic acid, citric acid or a fruit acid with moisture can dissolve part of the oxide, release water and change the pH of the powder. The reaction may be harmless or may cause caking and a colour change; either way it should be tested rather than discovered on the shelf.

An effervescent or instant drink is the deliberate version of the same reaction. The acid dissolves the oxide when water is added, and the solution is clear only if the acid is in excess and the oxide is fine enough. That is a formulation design, and its stability belongs to the finished product.

How the shelf life is set

No single shelf-life figure is published for this oxide. The pack and the storage condition set the period, and it is written into the specification and backed by data generated in that pack. A figure with no pack, no condition and no test panel is a claim, not a shelf life.

Once the retest period ends, the retain is re-assayed before any extension is agreed. An extension is never assumed, and a figure from the bulk pack does not transfer to a container that was repacked elsewhere. The standard packs are listed on the zinc oxide product page; pack and lead time are on the MOQ page; the release tests are on the COA page; the elemental panel is explained in the ICP-MS note; the release process is set out on the quality page.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation