M Potency · EDTA titration

Complexometric titration (EDTA) for mineral ingredients

Technical note · Reviewed 18 November 2026 · All methods

An EDTA titration is the standard complexometric assay for magnesium in a mineral powder. The sample is dissolved, buffered and titrated with disodium edetate until a metal indicator changes colour, and the volume of titrant gives the total magnesium. It is the method most magnesium certificates lead with, and it answers a narrower question than the certificate suggests.

In short

A direct titration that reports total magnesium in the sample, and nothing about the form it came from.

How the titration is carried out

Disodium edetate forms a 1:1 complex with magnesium, and the formation is quantitative at pH 10, so the volume of titrant maps directly onto the amount of magnesium in the flask. An ammonia–ammonium chloride buffer holds that pH, and a metal-ion indicator such as Eriochrome Black T turns from wine red to blue at the endpoint. The reaction is not specific to magnesium, which is why the sample preparation and the masking strategy matter as much as the titration itself.

The sample is weighed, dissolved and diluted to a known volume, and an aliquot is buffered before titration. Oxide and carbonate grades need an acid digestion step first, because a neutral suspension of magnesium oxide dissolves slowly and will under-report if the titration is rushed. A blank is carried through the same procedure, and the edetate solution is standardised against a certified metal standard rather than assumed to be exact.

The calculation is straightforward stoichiometry: titrant volume times molarity times the atomic mass of magnesium, corrected for the aliquot and the sample weight. Results are usually reported to one decimal place as elemental magnesium, alongside the theoretical value for the form named on the specification. Duplicate titrations and a control sample are what separate a release result from a single number.

What the result proves

The titration measures total elemental magnesium in the portion that dissolved, and it does so with an accuracy that is adequate for a release specification. For an anhydrous 1:2 chelate the theoretical magnesium content is about 14.1%, so a lot returning 13.9–14.2% is consistent with that form. The same number on a certificate is a statement about quantity, not about identity.

It answers the potency question cleanly: does this lot contain the magnesium it claims, batch after batch. Combined with a glycine assay, it supplies the magnesium figure from which the Mg : glycine ratio is calculated. It is also a method that many contract laboratories can run without special equipment, which is why it appears on so many certificates.

The result is also the basis for the label arithmetic. A buyer converting a chelate weight into an elemental magnesium claim uses this percentage, and a small assay bias turns into a label shortfall at the capsule fill stage. That is a reason to look at the method and the repeatability, not only at the pass mark.

What it cannot tell you

The titration cannot distinguish magnesium bisglycinate from magnesium oxide, magnesium citrate or a buffered blend, because all of them deliver magnesium ions to the same buffer. A formulator can build a blend that returns exactly the magnesium percentage of the chelate, and the titration will pass it. The certificate has to be read with the ligand assay, the ratio and a phase check before the word chelate is accepted.

Other divalent and trivalent metals compete for the same titrant and can block the indicator, so calcium, zinc, iron, aluminium or copper in the sample bias the result. Masking agents such as potassium cyanide, triethanolamine or hydroxylamine suppress some of these interferences, and a back-titration is used when the direct endpoint is poor. Phosphate and carbonate matrices can precipitate magnesium and take it out of the titration.

The endpoint is visual, and the change from wine red to blue is judged by an analyst under a particular lamp. Photometric endpoint detection reduces that subjectivity, but method transfer between laboratories can still move a result by a few tenths of a percent. None of this is visible on a certificate that reports only a percentage and a pass mark.

What it proves

  • Total elemental magnesium in the portion that dissolved, reported as a percentage by mass.
  • Whether a lot meets the magnesium assay range in its release specification.
  • Batch-to-batch consistency when the same standard, buffer and indicator are used.
  • The magnesium input to the Mg : glycine molar ratio calculation.

What it does not prove

  • The chemical form: oxide, citrate, a chelate and a buffered blend can return the same percentage.
  • Free glycine, bound glycine or the molar ratio between them.
  • Heavy metals and other trace contaminants at mg/kg or µg/kg levels.
  • Crystal phase, coordination or the species present in solution.

What to ask the laboratory

  1. Is the edetate solution standardised against a certified standard, and what is the current titer?
  2. How is the sample brought into solution, and does the digestion dissolve oxide if it is present?
  3. Which indicator and buffer are used, and is the endpoint visual or photometric?
  4. What is the repeatability on this matrix, and is the method inside your ISO/IEC 17025 scope?

Read the assay against the form named in the specification, not against a generic magnesium figure. The theoretical value for anhydrous magnesium bisglycinate is about 14.1%, so a lot at 14.0% is consistent with the chelate, but the same number can be built from a blend. Check that the certificate names the buffer, the indicator and the standardisation of the titrant, and read the result together with glycine and the molar ratio.

Where the method is used

The method pages sit behind the COA page. The terms used here are defined in the buyer glossary, and the regulatory limits are on the compliance page.

Send the certificate or specification you are reviewing and we will name the method behind each figure.

Request a specification review

Next step

A number without a method is not a result.

Send the certificate and we will name the method, the limit and the gap.