What the COA for zinc gluconate actually contains
The certificate for a zinc gluconate lot reports appearance, the salt assay by complexometric EDTA on the anhydrous basis, elemental zinc, the identification tests, pH of the 10% solution, loss on drying, particle size, heavy metals and microbiology. Each line should carry the method, the release limit and the lot result. The ranges below are the catalog specification; the batch COA confirms a particular drum.
The certificate has to show three things at once: the assay on the anhydrous basis, the elemental zinc the label will use, and the gluconate tests that separate this salt from an oxide or a citrate.
The certificate as a test report
A certificate earns its place when a stranger can audit it: parameter, method, release limit and result on every line. A sheet with a method column and no result column is a specification with a letterhead.
| Parameter | Method | Release limit |
|---|---|---|
| Appearance | Visual | White to off-white crystalline powder |
| Assay (anhydrous basis) | Complexometric EDTA titration | 97.0–102.0% |
| Zinc (Zn) | Complexometric EDTA titration | 12.5–14.0% |
| Identification | Zinc reaction, gluconate reaction and infrared spectrum | Conforms |
| pH (10% solution) | Potentiometry | 6.0–7.5 |
| Loss on drying | Gravimetric | ≤1.0% |
| Particle size | Sieve analysis | ≥95% through 80 mesh |
| Parameter | Method | Release limit |
|---|---|---|
| Heavy metals | ICP-MS | Pb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg |
| Microbiology | Plate count and absence tests | APC ≤1,000 cfu/g; yeast and mould ≤100 cfu/g; E. coli and Salmonella absent |
The first table covers the molecule and its condition; the second covers the contaminants a buyer must check against a finished-product limit.
Assay and zinc are two views of one titration
The assay is the mass of zinc gluconate, expressed against the anhydrous molecule; zinc is the element inside it. Both come from one complexometric titration: disodium edetate binds zinc one to one, and the laboratory converts the zinc result into salt with a factor.
The factor comes from the formula. Anhydrous zinc gluconate, C12H22O14Zn, has a molar mass of about 455.7 g/mol, and zinc accounts for 65.38 of that. The theoretical zinc content is therefore 65.38 ÷ 455.7 = 14.35%, and the reciprocal, 6.97, converts zinc back into salt. A lot reporting 14.1% zinc is reporting an assay of about 98.3%.
That arithmetic is the first audit check. If a certificate shows an assay of 101.0% and a zinc result of 13.0%, the pair cannot both be right, because 13.0% zinc converts to about 90.6% salt. One figure has been calculated on another basis, or copied from another line. Ask which figure the laboratory measured and which it calculated.
The anhydrous basis is the second check. The result is corrected for the water measured by loss on drying, and the correction is small because the ceiling is ≤1.0%. Small is not zero: a certificate that reports the assay “as is”, or corrects one figure and not the other, will not reconcile with the zinc line. The basis belongs in the column heading.
Neither figure identifies the anion. EDTA sees zinc, and zinc is present in the oxide, the citrate, the sulfate and the gluconate. The zinc reaction proves the element; the gluconate reaction and the infrared spectrum prove the ligand.
Release limit, batch result and the word “conforms”
The release limit is the gate; the batch result is what the laboratory measured. They belong in separate columns with the method beside them. A result column repeating the range is a copy of the gate, not evidence that it was passed.
Three lines deserve a result rather than a tick. Loss on drying has a ceiling of 1.0%, the whole allowance for surface water on a freely soluble powder; 0.9% is inside the gate but close to it, and a humid room will move it. pH of the 10% solution sits at 6.0–7.5; a low reading can point to residual gluconic acid, a high one to unreactioned zinc oxide. Neither proves a defect, but each is a question for the batch record.
The heavy-metal panel should report each element against its own limit with the laboratory's quantification limit. “Heavy metals: passed” is a conclusion without a number. The same applies to microbiology: the absence tests should name the organism and the sample size, and the APC and yeast-and-mould results should be figures.
“Conforms” is acceptable for the identification tests, and only when the certificate names the reference. An infrared comparison with an unnamed spectrum is a comparison with something.
What moves between lots
Zinc moves with the reaction and crystallisation, and the assay follows because both come from one titration. Loss on drying moves with the drying step and the pack: a drum closed late reads higher than one sealed at the line. pH moves with the neutralisation endpoint, and particle size moves with the mill and sieve — the parameter that most often changes when a supplier switches site.
Colour and flow are the qualitative signals. A grey or yellow cast can follow a hot drying step, a trace of iron or a wet mill while the assay stays inside its window. Read it with the batch record; a trend across three lots says more than one result at an edge.
The lot code belongs on the certificate, the drum label and the retained sample, together with the site and the form the lot was released against.
When an outside test is worth ordering
Four situations justify it: a new source, a first shipment into a regulated market, an identity claim the supplier's own certificate does not prove, and a disputed result. The useful panel is targeted rather than a full repeat: a second EDTA titration, ICP-MS for the four contaminant elements, X-ray diffraction for crystalline zinc oxide and FTIR against a gluconate reference.
If a diluent is suspected, add a glucose test and a loss-on-drying repeat. Ask for the detection limit on the diffraction screen: a “not detected” line without a limit describes the method, not the sample.
Chain of custody matters as much as the method. The sample tested should be the sample retained, and the report should name the lot, the sample weight and the basis. The XRD note and the ICP-MS note set out what each technique can establish.
Six lines to put side by side
When two quotations arrive, compare the hydrate state, the assay with its basis, the zinc result, the identification tests with the reference named, loss on drying, and the mesh. Two certificates that agree on zinc and disagree on the other five are not describing the same powder.
The second layer is traceability: who made the lot, which zinc source and drying step were used, and whether the certificate matches the drum. A correct certificate can still belong to a different lot.
The catalog specification sits on the zinc gluconate product page. The salt comparison is on the grade page, the identity tests are on the identity page, and the release workflow is on the quality page. The titration itself is described in the complexometric method note.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation