06 Identity & adulteration

How we prove a zinc gluconate lot is the gluconate

Technical document 06 · Reviewed 2026-11-18 · Zinc Gluconate

On this page
  1. Four layers, four different failures
  2. One zinc per gluconate, and what that fixes
  3. What infrared and diffraction add
  4. The routes that move one number at a time
  5. How to write the identity specification
  6. Five questions for the supplier

A zinc gluconate lot is proved on four levels: the molecule named on the paper, the zinc ion by reaction, the gluconate ligand by chromatography and infrared spectrum, and the assay on the anhydrous basis with the condition tests around it. The EDTA titration proves quantity; the ligand tests prove which salt the zinc is in. A certificate that reports only zinc has proved neither the anion nor the form.

In one line

Zinc proves the element, the gluconate reaction and infrared spectrum prove the ligand, and the anhydrous assay proves how much salt is there.

Four layers, four different failures

What each identity layer establishes for zinc gluconate
LayerEvidenceWhat it establishesWhat it cannot
PaperName, formula, CAS 4468-02-4, anhydrous state, siteThe file describes the right moleculeNothing about the powder in the drum
ElementCompendial zinc identification testsZinc is presentWhich zinc salt it is
LigandGluconate reaction, TLC against a gluconate reference, infrared spectrumThe gluconate ion is presentHow much salt is there
Quantity and conditionEDTA assay on the anhydrous basis, loss on drying, pH, mesh, metals, microThe lot meets the specificationThat the ligand is gluconate

Each layer catches a different failure: a wrong name or missing hydrate on the paper, a non-zinc powder at the element, a different salt at the ligand, a weak or diluted lot at the assay. A certificate with a tick in all four columns is auditable; one with a zinc figure alone is a single number doing four jobs.

The zinc tests give the characteristic white hydroxide precipitate, soluble in excess alkali, and a white ferrocyanide precipitate. Neither is specific to gluconate, which is why the ligand sits beside it.

One zinc per gluconate, and what that fixes

There is no ligand ratio to calculate here, as there would be for a chelate. Zinc gluconate is a 1:1 salt: one zinc ion for one gluconate ion. The anhydrous molecule weighs about 455.7 g/mol and zinc accounts for 65.38, so the theoretical zinc content is 14.35% and the reciprocal, 6.97, converts a zinc result into salt. That fixed ratio is an identity tool, because it sets a ceiling: zinc above 14.35% cannot come from zinc gluconate alone.

Take a hypothetical certificate with 13.9% zinc as-is and 0.5% loss on drying. The anhydrous zinc is 13.9 ÷ 0.995 = 13.97%, and the assay is 13.97 × 6.97 = 97.4%. That is the arithmetic the certificate should reproduce. If the same sheet reported 14.0% zinc and an assay of 102%, the pair could not both be right: 102% requires 14.6% zinc, and 14.0% caps the assay at 97.6%. One figure was calculated on another basis or copied from a different line.

The anhydrous basis makes the pair comparable. With loss on drying ≤1.0% the correction is small but not optional: an as-is assay and an anhydrous assay differ by the water figure, and a certificate that does not say which it used cannot be reconciled with the zinc line. A hydrate would move the whole calculation.

What infrared and diffraction add

The infrared spectrum is a fingerprint of the gluconate ligand. Carboxylate absorption sits near 1600 and 1400 cm⁻¹, the broad hydroxyl band near 3400 cm⁻¹, and the spectrum is compared with a reference of the same form rather than interpreted band by band. In the USP identification the ligand is also compared by thin-layer chromatography against a potassium gluconate reference, which is a sharper test than a colour reaction: it separates gluconate from other sugar acids and from glucose. IR answers “is this the gluconate salt?” It does not answer “how much?” and it is not a purity assay.

X-ray diffraction reads the crystal lattice. It distinguishes crystalline zinc oxide and zinc citrate from zinc gluconate, and it can separate an anhydrous pattern from a hydrate if a reference pattern is available. It will not see an amorphous diluent, and it will not quantify a phase below its detection limit. Ask the laboratory for the reference pattern and the limit. A “conforms” with no reference named is a comparison with something unnamed. The FTIR note and the XRD note explain what each technique can establish.

The routes that move one number at a time

Adulteration routes for zinc gluconate and the tests that show them
RouteWhat movesTest that shows it
Zinc oxide (about 80% zinc)Zinc and the calculated assay rise sharplyXRD; assay zinc above the 14.35% ceiling
Zinc citrate (about 32% zinc)Zinc rises, the anion changesInfrared, citrate reaction, XRD
Glucose, dextrose or maltodextrinZinc and assay fall, loss on drying may riseAssay, infrared, glucose by HPLC
Zinc sulfate (about 23% zinc as heptahydrate)Zinc rises, taste sharpens, sulfate appearsSulfate test, infrared
WaterAs-is zinc falls, anhydrous zinc holdsLoss on drying beside the assay

The routes share a signature: one number moves while another stays, so read the figures in pairs. A zinc result near the 14.35% ceiling with a low loss on drying points to added zinc oxide or citrate; a low zinc with a high loss on drying points to water or a diluent; a reconciling zinc figure with a mismatched infrared spectrum points to the wrong ligand.

A declared blend is not adulteration. If the powder contains zinc gluconate and another zinc source, the label has to name both and the certificate has to report the contribution. The defect is the undeclared blend, not the blend itself.

How to write the identity specification

  • “Zinc gluconate, C12H22O14Zn, CAS 4468-02-4; anhydrous form declared.”
  • “Identification: compendial zinc tests; gluconate by TLC against a gluconate reference and by infrared spectrum against a named reference.”
  • “Assay 97.0–102.0% on the anhydrous basis by complexometric EDTA; zinc 12.5–14.0%.”
  • “Loss on drying ≤1.0%; pH of the 10% solution 6.0–7.5; ≥95% through 80 mesh.”
  • “No added zinc oxide, zinc citrate, zinc sulfate or glucose; heavy metals and microbiology as the catalog.”

A specification written this way tells the laboratory what to measure and the supplier what will be rejected. “Assay 13%” does none of that: it does not say whether the figure is zinc or salt, as-is or anhydrous, or which ligand the zinc is bound to.

Five questions for the supplier

  1. Which zinc figure is reported, and is the assay calculated on the anhydrous basis?
  2. Do the zinc and assay results reconcile through the 6.97 factor, and what is the loss on drying behind the correction?
  3. How is the gluconate identified — TLC, infrared, or both — and against which reference?
  4. Is the form anhydrous, and does the certificate name the hydrate state and the CAS number?
  5. Who manufactured the lot, and can the batch record and retained sample be tied to the lot code?

Five answers amount to an identity file; a single zinc percentage does not. The COA page shows where each figure sits on the certificate, the grade page places the salt among its alternatives, and the quality page describes the lot record. The catalogue line is on the zinc gluconate product page.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation