What the COA for magnesium chloride actually contains
Magnesium chloride hexahydrate is a white, deliquescent solid that carries more than half its mass as water of crystallisation, so its certificate cannot be read like a dry salt's. The release lines are appearance, identity by IR and titration, assay by complexometric titration, magnesium, water by Karl Fischer, the heavy-metal panel and microbiology. The two figures that decide whether two certificates describe the same material are the assay basis and the water.
On a hexahydrate that is more than half water, the assay only means something with its basis, the Karl Fischer water and the chloride beside it.
The certificate as a test report
A certificate is auditable when each line carries the parameter, the method and the release limit, and the measured result sits in its own column. The table below is the catalog gate for the hexahydrate. It is not a batch result: the lot result belongs beside the limit it was released against, not in place of it.
The identity pair in the catalog is IR plus titration. That pair names the magnesium salt and the hydrate family, but it puts no number on the anion. Chloride by argentometric titration is the line that does, and it is worth asking for even where the catalog leaves it off; the titration method note explains what the EDTA end-point does and does not prove.
| Parameter | Method | Release limit |
|---|---|---|
| Appearance | Visual | White powder or flakes |
| Identification | IR and complexometric titration | Conforms to the reference |
| Assay | Complexometric titration | ≥99.0% on the stated basis |
| Magnesium | Complexometric titration | 11.5–12.5% |
| Water | Karl Fischer | 45.0–55.0% |
| Heavy metals | ICP-MS | Pb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg |
| Microbiology | Plate count and absence tests | APC ≤1,000 cfu/g; yeast and mould ≤100 cfu/g; E. coli and Salmonella absent |
The basis question: 99.0% of what?
On a dry salt, a 99.0% assay needs little explanation. Here it needs one, because the same powder can be described as 99.0% magnesium chloride hexahydrate or as roughly 46% magnesium chloride with the water removed. The first reading takes the hydrate as the substance; the second takes anhydrous MgCl2 as the substance and reports it on the dried basis. Both are legitimate. They are not the same number.
The magnesium line does not settle it. If the 99.0% is the hydrate as-is, 99% of the theoretical 11.96% magnesium lands at about 11.8%. If the 99.0% is MgCl2 on the dried basis, the as-is MgCl2 content is about 46.4%, and the magnesium is again about 11.8%. The two certificates agree on magnesium and disagree on the assay by more than a factor of two. Only the basis distinguishes them.
The water line is the second half of the same question. The hexahydrate carries 53.2% water at the theoretical formula; the catalog allows 45.0–55.0%. If the only other component were MgCl2, 45% water would leave 55% MgCl2 and about 14.0% magnesium — outside the magnesium range. A certificate reporting 45% water and 12.0% magnesium is therefore not describing a simple hexahydrate, whatever the assay line says. The two figures have to be read together, and a lot near an edge of one range should be checked against the other.
Release limit versus batch result
The release limit is the boundary; the batch result is the measurement. A result column filled with the specification range is a copy of the gate, not evidence about the lot. The certificate should also name the method for each line, because a magnesium figure by EDTA and a magnesium figure by ICP-OES answer slightly different questions.
| Parameter | Release limit | Result column |
|---|---|---|
| Assay | ≥99.0%, with the basis | A measured percentage and the basis it is reported on |
| Magnesium | 11.5–12.5% | A measured percentage by the named titration |
| Water | 45.0–55.0% | A measured percentage by Karl Fischer |
| Chloride | Reported against the theoretical 34.9% | A measured percentage, where the anion is tested |
| Heavy metals | Per element | A figure in mg/kg for each element |
| Microbiology | Counts and absence | The count and the absence statement for the lot |
“Conforms” is a conclusion, and the reader should be able to reach it from the numbers. For the anion, a chloride result far above the theoretical 34.9% points to sodium chloride or another chloride source; a result far below it points to an oxide, a carbonate or a different magnesium salt. Neither is visible in the assay alone.
What moves between batches
Water is the parameter that moves most. Crystallisation and drying set it, and the pack then decides whether it stays put. A lot dried to the low end of the range can pick up water in a humid filling room before the pouch is sealed; the water result on the certificate then describes the sample, not the pack. Ask when the sample was taken and whether it came from a sealed container.
The physical form moves with the finishing line: a powder and a flake can come from the same crystalliser and differ in bulk density, flow and dissolution rate. The chloride figure can shift with the brine source, and the heavy-metal panel with the source and the purification step. Colour is a weak signal on a white salt; a grey or yellow tint is a reason to ask about the source and the filters, not a specification failure on its own.
When to order an outside test
Order an independent test for a new source, a first shipment, a shift in the water or chloride figure, or a disputed hydrate state. The useful panel is magnesium by EDTA, chloride by argentometric titration, water by Karl Fischer, ICP-MS for the heavy metals, microbiology, and XRD when the solid form is the question. If the source is brine or seawater, add sulfate and bromide by ion chromatography; neither line is in the catalog, and both are plausible companions in that raw material.
For a disputed lot, the sample tested must be the retained sample from the sealed pack, and the report must name the lot. A water result from an opened scoop is evidence about the room, not about the drum. The ICP-MS method note covers the contaminant panel, and the microbiology note covers the counts and absence tests.
What to compare between suppliers
Put six lines side by side: the hydrate state and the water figure; the assay and its basis; magnesium and chloride on the same lot; the contaminant panel; the pack and its liner; and the lot code, which should match the certificate, the pouch and the retained sample. Two quotations that agree on magnesium but differ on the assay basis are not describing the same specification.
The catalog specification is on the magnesium chloride product page. The hydrate question is taken further on the grade page; the identity tests are on the identity page; the release workflow is on the quality page, and the methods library is at the analytical methods index.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation