06 Identity & adulteration

How we prove a magnesium chloride lot is the hexahydrate

Technical document 06 · Reviewed 2026-11-19 · Magnesium Chloride

On this page
  1. Five layers, five questions
  2. The 1:2:6 ratio
  3. X-ray diffraction: the solid-state check
  4. What adulteration looks like
  5. How to write the identity into the specification
  6. Five questions for the supplier

A magnesium chloride lot is the hexahydrate when the document, the magnesium, the chloride and the water agree. The magnesium titration says how much metal is present; the chloride says which anion carries it; the water says which hydrate the crystal is; and the X-ray pattern says which solid phases are in the drum. No single line proves the salt.

In one line

Identity is the magnesium and the chloride agreeing on the same lot, with the water of crystallisation closing the mass balance.

Five layers, five questions

A certificate can name the right material and still fail to prove it. The layers below are separate questions, and each one needs its own evidence. A supplier who answers only the first has described the paperwork, not the powder.

Layers of magnesium chloride hexahydrate identity
LayerQuestionTestWhat it proves
DocumentIs the hydrate named?Name, CAS number, formulaPaperwork only
MetalHow much magnesium?Complexometric titration with EDTAThe magnesium, not the salt
AnionIs the counter-ion chloride?Argentometric titration or ion chromatographyThe chloride
WaterWhich hydrate is it?Karl Fischer titrationThe hydrate state and free water
Solid stateWhich crystalline phases are present?X-ray diffractionThe crystal form and crystalline impurities

The first layer is necessary and quick. The next four are analytical, and they have to be run on the same lot. A magnesium figure from one batch and a water figure from another describe a hypothetical material, not a drum.

The 1:2:6 ratio

The formula is MgCl2·6H2O: one magnesium, two chlorides and six water molecules. On the theoretical formula that is 11.96% magnesium, 34.88% chloride and 53.17% water, and the mass ratio of magnesium to chloride is 0.343. Those three figures are the identity arithmetic, and they should be consistent on the same certificate.

The ratio catches the common substitutions. If the chloride runs high against the magnesium, sodium chloride is the likely addition, because it brings chloride without bringing magnesium. The arithmetic is bounded: at 12.0% magnesium and a water figure near 53%, the powder is essentially all hexahydrate, which carries 34.9% chloride, so a certificate reporting 12.0% magnesium and 40% chloride is internally impossible rather than merely impure. If the chloride runs low against the magnesium, the likely addition is an oxide, a carbonate or a hydroxide, all of which lift the magnesium without lifting the chloride. If the water is low, the crystal is partly dehydrated and the magnesium figure per gram is higher than the hexahydrate's.

The water line can also expose a blend. A powder made from the hexahydrate and the anhydrous salt can be formulated to land inside the magnesium range, but its water figure falls below the hexahydrate's, and the ratio moves with it. The magnesium sees the total metal; the water sees the hydrate. Neither sees the whole material alone.

The assay basis is a separate question and belongs on the certificate, not in the ratio. The COA page sets out why a 99.0% figure on this hydrate can mean two different numbers.

X-ray diffraction: the solid-state check

X-ray diffraction answers a different question: which crystalline phases are present, and does the pattern match a reference? The hexahydrate has its own pattern, and the anhydrous salt and the lower hydrates have theirs, so a pattern can separate a partly dehydrated lot from a fresh one. It can also show sodium chloride or magnesium oxide as a second phase, which the wet chemistry has to infer from a ratio.

XRD is not a purity assay. It sees crystalline phases above its detection limit, not amorphous material and not a thin coating, and the sample preparation changes what the pattern represents. Ask for the reference pattern, the detection limit and the preparation method before reading a “match” statement. The XRD method note explains what the technique can and cannot see.

What adulteration looks like

Substitutions and the signals that expose them
AdulterantWhat it doesSignalTest
Sodium chlorideCheap chloride; lowers magnesium per gramChloride high against magnesium; sodium presentChloride, sodium by ICP-OES, XRD
Magnesium sulfateWhite, bitter, different anionSulfate present; chloride low against magnesiumIon chromatography, XRD
Magnesium oxide or carbonateLifts magnesium; lowers water and chlorideMagnesium high; water low; haze in waterXRD, acid test, Karl Fischer
Calcium chlorideDeliquescent; cheaper divalent chlorideCalcium present; magnesium lowICP-OES, XRD
WaterRaises the water figure; cakingWater above 55%; pouch weight gainKarl Fischer, weight gain

Colour is the weakest signal on a white salt, and a small addition of sodium chloride or magnesium sulfate changes nothing visible. The stronger signals are the chloride-to-magnesium ratio, the water figure, the sodium and calcium results and the diffraction pattern. A certificate that reports appearance and magnesium but not chloride and water has left the most likely substitutions untested.

How to write the identity into the specification

  • “Magnesium chloride hexahydrate, CAS 7791-18-6, MgCl2·6H2O.”
  • “Assay ≥99.0% by complexometric titration, with the basis stated.”
  • “Magnesium 11.5–12.5%; water 45.0–55.0% by Karl Fischer.”
  • “Chloride reported against the theoretical 34.9%.”
  • “Identification by IR and titration; chloride by argentometric titration.”
  • “XRD reference pattern and detection limit stated where the solid form is tested.”
  • “No added sodium chloride, magnesium sulfate, magnesium oxide or calcium chloride.”

Five questions for the supplier

  1. Which hydrate is this lot, and what is the water figure by Karl Fischer?
  2. What is the assay basis, and is the result reported on the hydrate or on MgCl2?
  3. What are the magnesium and chloride figures on the same lot, and by which methods?
  4. Is there a sodium result by ICP-OES and an XRD pattern, and what detection limit does each state?
  5. If the lot is disputed, will you accept a joint re-test on the retained sample?

Five direct answers amount to an identity file. A single magnesium percentage does not. The product hub carries the catalog specification; the COA page shows where each figure sits on the certificate; the grade page compares the hydrate forms; the quality page describes the retained-sample workflow.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation