01 COA & batch testing

Reading a magnesium bisglycinate hydrate COA

Technical document 01 · Reviewed 2026-11-20 · Magnesium Bisglycinate Hydrate

On this page
  1. What the one-page certificate reports
  2. As-is, dried basis and the hydrate name
  3. Release limit, batch result and the ratio
  4. What moves between batches
  5. When to order an outside test
  6. Comparing quotations line by line

A magnesium bisglycinate hydrate certificate has to be read as a pair of numbers, not one. The magnesium result says how much of the element the powder carries; the loss-on-drying result says how much of that powder is water. The catalog sets magnesium at 11.0–12.5% by complexometric titration, loss on drying at 8.0–14.0%, and the Mg : glycine ratio at 1:2 with glycine by HPLC. The basis must be stated beside the magnesium figure.

In one line

On a hydrate certificate the magnesium figure and the water figure must be read as a pair: 11.0–12.5% Mg beside 8.0–14.0% loss on drying is the grade, and either number alone is not.

What the one-page certificate reports

Every line should carry the parameter, the method, the release limit and the measured result in its own column. A certificate that reports only “conforms” asks the buyer to accept a conclusion without evidence, and the same magnesium figure can come from a chelate, a blend or a drier grade.

Release tests · magnesium bisglycinate hydrate
TestMethodLimit
AppearanceVisualWhite to off-white, free-flowing powder
IdentificationGlycine by HPLC and magnesium by titrationBoth conform to the reference
Magnesium (Mg)Complexometric titration11.0–12.5%
GlycineHPLCConsistent with the 1:2 molar ratio
Mg : glycine ratioCalculated from the two assays1 : 2 molar
Loss on dryingGravimetric8.0–14.0%
Heavy metalsICP-MSPb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg
MicrobiologyAerobic plate count; absence testsAerobic count ≤1,000 cfu/g · yeast and mould ≤100 cfu/g · E. coli and Salmonella absent
Particle sizeSieve analysis≥95% through 80 mesh

The particle-size line is a finishing specification: changing the mill or the sieve can move it while the chemistry stays the same. Microbiology is a second block, with the count and the absence result for that lot, and the lot code should match the pouch, the drum and the retained sample.

As-is, dried basis and the hydrate name

An as-is figure takes the powder as weighed; a dried-basis figure divides by the dry matter and reports what the solids would contain without water. The catalog magnesium range here is as-is, because the water is part of the material being sold.

The conversion is easy to get wrong. A lot at 11.8% magnesium as-is beside 10.0% loss on drying calculates to 11.8 ÷ 0.90 = 13.1% on the dried basis. That is arithmetic, not a batch result. The powder is still the hydrate, and the as-is figure sets the fill weight. Comparing 13.1% dried basis with the 13.5–14.2% anhydrous range makes the two materials look closer than they are.

The word “hydrate” alone does not fix the water. The catalog window, 8.0–14.0% loss on drying, is wider than a single stoichiometric hydrate. The certificate should report the measured water and magnesium, and the technical data sheet should name the grade; a percentage such as “98%” without a basis is not a substitute.

Release limit, batch result and the ratio

The release limit is the boundary the lot must fall inside; the batch result is what the laboratory measured. They belong in separate columns with the method beside them. “Passes specification” is a conclusion; the numbers are the evidence.

What the result column should show
ParameterRelease limitResult column
Magnesium11.0–12.5% as-isA measured percentage, with the method and the basis
Loss on drying8.0–14.0%A measured percentage on the same sample
Glycine and ratio1 : 2 molarThe glycine result and the calculated ratio
Heavy metalsPer elementA figure in mg/kg for each element
MicrobiologyCounts and absenceThe count and the absence result for that lot

Two released lots can still differ in magnesium per gram by about 14%, because one may sit at 12.5% magnesium with 8.0% water and the other at 11.0% with 14.0%. That is the width of the grade, not a quality failure; the fill weight comes from the certificate result, not the catalogue midpoint.

The catalog does not set a free-glycine limit on this grade; it can be added as a separate line. The magnesium window limits how much oxide could be present but does not prove absence, so an oxide screen is a separate request, with its detection limit stated.

What moves between batches

The drying and hydration steps move loss on drying, and the as-is magnesium figure moves the other way. A lot that has picked up water shows higher loss on drying and lower magnesium, while the chelate itself is unchanged; a lot dried harder moves in the opposite direction. Read the two trends together.

The glycine result and ratio should stay close to 1:2. A drift away from 1:2 is more serious than a small colour difference: it suggests added glycine, a second magnesium source or a different reaction product. Particle size follows milling, and bulk density follows shape and moisture. Colour is the least quantitative line; a tan tint within the off-white window should prompt a batch-record review, not an automatic rejection.

A run of lots is more informative than a single result close to a limit. Magnesium drifting down while loss on drying climbs points to moisture pickup; magnesium drifting up while loss on drying falls points to over-drying or a different hydrate. Either changes the fill weight even when every lot is in specification.

When to order an outside test

An independent test is worth ordering for a new source, a first regulated shipment, a disputed hydrate state, or a label claim the certificate does not prove. The useful panel is magnesium by titration or ICP-OES, water by loss on drying or Karl Fischer, glycine by HPLC, a phase check by XRD or TGA, ICP-MS for the heavy metals and the microbiology block.

Ask for the detection limit of each screen; a “not detected” line without a limit describes the method, not the sample. Keep the tested sample and the retained sample from the same pack, and make the report identify the lot. A contested result needs the retained sample, the certificate, the specification and the tests that separate the hydrate from the anhydrous grade, not a repeat of the same magnesium assay.

Comparing quotations line by line

Compare six lines across suppliers: the product name, hydrate statement and CAS number; the magnesium result and its basis; loss on drying; glycine and the calculated ratio; particle size and heavy metals; and the lot code linking certificate, pack and retained sample. Two quotations that agree on magnesium but differ on water are not the same grade.

The catalog specification is on the hydrate product page. The other grade is on the anhydrous page; the water and fill arithmetic is on the anhydrous versus hydrate comparison. Analytical methods are in the methods library, and the release workflow is on the quality page.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation