Anhydrous vs hydrate magnesium bisglycinate: water, magnesium and fill weight
The anhydrous and hydrate grades are the same 1:2 magnesium–glycine chelate with different amounts of water. The anhydrous grade carries 13.5–14.2% magnesium, about 14.1% at the theoretical formula; the hydrate carries 11.0–12.5% magnesium and 8.0–14.0% water. For a 100 mg elemental magnesium dose, the hydrate needs 800–909 mg of powder against about 709 mg of the anhydrous grade, so the fill weight, the capsule count and the water the formula receives all change.
The two grades differ by water: the anhydrous chelate carries about 14.1% magnesium, the hydrate 11.0–12.5%, so the same label dose needs roughly 13–28% more hydrate powder.
Two grades, one CAS number
Both catalog records carry CAS 14783-68-7, so the certificate name, the magnesium result and the water result are what separate the grades. A purchase order that names only the CAS number has not chosen a grade.
| Property | Anhydrous grade | Hydrate grade |
|---|---|---|
| Catalog magnesium | 13.5–14.2% | 11.0–12.5% |
| Water | Separate moisture limit | 8.0–14.0% loss on drying |
| Theoretical magnesium | About 14.1% | About 12.8% as a monohydrate, 11.7% as a dihydrate |
| Formula | C4H8MgN2O4 | C4H8MgN2O4·xH2O |
| Particle size | ≥95% through 40 mesh | ≥95% through 80 mesh |
| Appearance | White to off-white crystalline powder | White to off-white powder |
| Label name | Magnesium bisglycinate | Magnesium bisglycinate hydrate |
The formula row explains the chemistry and the label row the commercial decision. The hydrate is not a diluted anhydrous powder; it is a hydrate of the same chelate, sold as its own grade, and the two names are not interchangeable.
The magnesium figure per gram
Magnesium is 24.305 g/mol and the anhydrous chelate 172.42 g/mol, so the theoretical content is 14.10%. The catalog range 13.5–14.2% brackets that value, and a kilogram carries about 135–142 g of elemental magnesium.
The hydrate carries less magnesium per kilogram because water adds mass without adding the element. At 11.0–12.5% magnesium, a kilogram carries 110–125 g. Against the 14.1% theoretical anhydrous figure, the same magnesium dose needs about 13% more hydrate powder at 12.5% magnesium, about 28% more at 11.0%, and about 20% more at the 11.75% midpoint.
The comparison is only valid on the same basis. The hydrate's 11.0–12.5% is as-is. Convert a dried-basis result back before comparing: 11.8% as-is beside 10.0% loss on drying is 13.1% dried basis, still the hydrate. The as-is figure sets the fill.
What the water does to the mass
Water is 8.0–14.0% of the powder by the loss-on-drying limit. In a 100 mg magnesium dose that is roughly 64–127 mg of water. In a low-moisture tablet or gummy, that water is part of the matrix's water activity and drying step, even though the ingredient is sold dry.
The water also widens the grade. Two released lots can differ by about 14% in magnesium per gram: one at 12.5% magnesium with 8.0% water, another at 11.0% with 14.0%. Size the fill from the certificate result for the lot that will ship, not the catalogue midpoint.
The hydrate is closer to its equilibrium water content than the anhydrous grade, which has an empty hydration site and takes water readily. That does not make the hydrate safe in an open room: it is still hygroscopic, it still cakes, and the pack still has to be sealed. Loss on drying measures crystal water and surface moisture; thermogravimetric analysis separates the two when the hydrate state is disputed.
The fill arithmetic
The label declares elemental magnesium; the weigh-up uses powder. Divide the declared dose by the magnesium fraction on the certificate. The table uses the theoretical anhydrous figure and three hydrate points, before excipient.
| Declared magnesium | Anhydrous at 14.1% | Hydrate at 11.0% | Hydrate at 12.5% | Hydrate at 11.75% |
|---|---|---|---|---|
| 50 mg | 355 mg | 455 mg | 400 mg | 426 mg |
| 100 mg | 709 mg | 909 mg | 800 mg | 851 mg |
| 200 mg | 1,418 mg | 1,818 mg | 1,600 mg | 1,702 mg |
In a capsule, the count follows. A 500 mg capsule of hydrate at 11.75% carries about 59 mg, so a 100 mg dose takes two capsules; the anhydrous grade fits about 70 mg, so it also takes two but has more room. A one-capsule 100 mg dose needs an 800–909 mg hydrate fill, a larger capsule or another dosage form.
For tablets, the extra 13–28% becomes compression weight, and the 80 mesh hydrate may need granulation. For a stick pack, the extra mass shows in net weight and scoop size; for a gummy, it brings the water discussed above. The arithmetic is the same; only the constraint changes.
What the label and the specification must say
The label has to name the grade that was weighed. For the hydrate, the declaration should identify magnesium bisglycinate hydrate, with elemental magnesium declared as the nutrient. In the US Supplement Facts the source is named in parentheses, for example “magnesium (as magnesium bisglycinate hydrate)”; in the EU ingredient list the hydrate description belongs with the ingredient name. The buyer's regulatory team confirms the wording.
The specification should carry the same two figures: magnesium 11.0–12.5% as-is and loss on drying 8.0–14.0%, with the 1:2 ratio. It should state the hydrate in the product name, because the CAS does not distinguish it. A switch between grades changes fill weight, label and stability work; it is a new specification, not a substitution at the balance.
When each grade earns its place
Choose the anhydrous grade when fill is the binding constraint, the formula has no room for the extra mass, or the label names the anhydrous chelate. It carries more magnesium and no crystal water, but it is more hygroscopic and needs a dry pack.
Choose the hydrate when the fill has room for 13–28% more powder, the matrix can accept the water, and the label names the hydrate. It is the grade specified on this page. Neither grade is a diluted version of the other; they are separate catalog items.
The catalog specification is on the hydrate product page; the other grade on the anhydrous page; the release tests on the COA page; the analytical methods in the methods library; the release workflow on the quality page.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation