06 Identity & adulteration

How to prove a magnesium bisglycinate hydrate lot

Technical document 06 · Reviewed 2026-11-20 · Magnesium Bisglycinate Hydrate

On this page
  1. The four identity layers
  2. The 1:2 ratio across the hydrates
  3. Water in the crystal: LOD, TGA and XRD
  4. What substitution looks like
  5. Specification clauses for the hydrate grade
  6. Five questions for the supplier

A magnesium bisglycinate hydrate lot is the named material when four results agree: magnesium inside 11.0–12.5%, loss on drying inside 8.0–14.0%, a 1:2 magnesium–glycine ratio, and a solid-state check that the water is part of the hydrate rather than a wet powder. The magnesium figure alone cannot separate the hydrate from the anhydrous grade at 13.5–14.2% or from a blend. The water result is the second half of the identity, not an extra line on the certificate.

In one line

A hydrate lot is identified by four agreeing figures: the 1:2 magnesium–glycine ratio, the magnesium result, the water result and a solid-state check that the water is part of the crystal.

The four identity layers

Each layer answers a different question, and each needs its own evidence. A certificate that gives only the magnesium result has answered the metal question and left the ligand, the water and the solid form open.

Identity layers · magnesium bisglycinate hydrate
LayerQuestionTestWhat it proves
DocumentIs the hydrate named, with the CAS number?Certificate and specificationPaperwork only
MetalIs the magnesium inside 11.0–12.5%?Complexometric titrationThe elemental content of the sample
LigandIs the ratio 1:2?Glycine by HPLC; ratio calculatedThat the glycine is consistent with the chelate
WaterIs the water inside 8.0–14.0%?Loss on drying or Karl FischerThe hydrate grade, not the anhydrous grade
Solid stateIs the water in the crystal?X-ray diffraction, TGA or FTIRHydrate form rather than surface moisture

The layers have to agree. A magnesium result inside the range with water at 3% is not the hydrate grade, however the certificate is titled. A water result inside the range with a magnesium figure near 14% is not the hydrate either; the two numbers describe different powders.

The 1:2 ratio across the hydrates

The chelate has one magnesium ion and two glycine ligands, so the molar ratio is 1:2 whether the powder is anhydrous or hydrated. The mass fractions move with the water: the anhydrous chelate is about 14.1% magnesium and 85.9% bound glycine; a monohydrate is about 12.8% magnesium and 77.8% glycine; a dihydrate is about 11.7% magnesium and 71.1% glycine. The ratio stays fixed while the percentages fall, which is why the ratio is a better identity check than either percentage alone.

The ratio is calculated from the magnesium and glycine assays, so its uncertainty is the sum of both methods. The specification should give a tolerance around 1:2, not a single figure. A glycine result above the 1:2 expectation points to added glycine or a low-magnesium carrier; a glycine result below it points to a second magnesium source or a partly different reaction product. Free glycine is not in this catalog specification; if the buyer needs it, it can be added as a separate line, and it is the measurement that separates bound ligand from added ligand.

Water in the crystal: LOD, TGA and XRD

Loss on drying measures the water that leaves the powder under the stated conditions. It does not, by itself, say whether that water was in the crystal or on the surface. Thermogravimetric analysis separates the mass losses as the sample is heated, and the shape of the curve can show a hydrate step rather than a smooth surface-moisture loss. X-ray diffraction compares the solid's pattern with a reference and can show a crystalline hydrate phase; Fourier-transform infrared spectroscopy adds the metal–ligand bands that a physical blend does not reproduce.

None of these methods is a routine release test for this grade, and each has a limit. A partly amorphous or mixed hydrate may not give a clean diffraction pattern, and a “not detected” statement is only meaningful with the detection limit attached. Ask for the raw curve or pattern, not only the word “conforms”, when the hydrate state is the question. A combination of loss on drying, magnesium and a solid-state check is stronger than any one of them.

What substitution looks like

Substitutions and the signals on a hydrate lot
SubstitutionWhat movesTest
Anhydrous grade sold as hydrateMagnesium high; water lowMagnesium plus loss on drying
Hydrate sold as anhydrousMagnesium low; water highMagnesium plus loss on drying
Added glycineGlycine high; above the 1:2 expectationGlycine by HPLC; free glycine
Magnesium oxide blendMagnesium above 12.5%; ratio lowXRD oxide screen; titration
Carbonate or hydroxide sourceMagnesium high; pH and solubility shiftXRD, FTIR, pH of a stated suspension

A common substitution is not a foreign substance; it is the other grade of the same chelate. The anhydrous powder is the same molecule with less water, so a certificate that names “magnesium bisglycinate” without the hydrate and reports 14% magnesium is not proving a hydrate. The water result and the product name are the two lines that catch it.

Specification clauses for the hydrate grade

  • “Magnesium bisglycinate hydrate, 1:2 chelate, CAS 14783-68-7.”
  • “Magnesium 11.0–12.5% by complexometric titration, as-is.”
  • “Loss on drying 8.0–14.0%; the hydrate state stated on the COA and the TDS.”
  • “Glycine by HPLC; Mg : glycine ratio 1 : 2 molar.”
  • “Particle size ≥95% through 80 mesh; appearance white to off-white.”
  • “No undeclared magnesium source; an oxide screen on request, with its detection limit.”
  • “A solid-state check reported when the hydrate state is disputed.”

Five questions for the supplier

  1. Is the product named magnesium bisglycinate hydrate on the certificate, and what are the magnesium and water results for this lot?
  2. What is the glycine result and the calculated Mg : glycine ratio?
  3. Is the 11.0–12.5% magnesium figure reported as-is or on a dried basis?
  4. Can you provide a loss-on-drying curve or a TGA/XRD report if the hydrate state is questioned?
  5. Is any magnesium source other than the chelate present, and is an oxide screen available?

Five direct answers amount to an identity file; a single magnesium percentage does not. The hydrate product page carries the catalog specification; the anhydrous grade is the nearest substitution risk; the COA page shows where each result sits; the methods library describes the assays; the quality page covers the release file.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation