Hydrate, anhydrous or granulated: choosing a magnesium bisglycinate grade
Magnesium bisglycinate hydrate is a grade, not a synonym for every magnesium glycinate powder. The catalog hydrate carries 11.0–12.5% magnesium and 8.0–14.0% water, while the anhydrous chelate is a separate product at 13.5–14.2% magnesium. Buffered blends, granulated powders and finer mesh are further choices within the same family. The grade is settled by the fill weight, the dosage form and the ingredient name the label has to use.
The hydrate grade is a window, not a single molecule: 11.0–12.5% magnesium with 8.0–14.0% water, specified and weighed as a pair.
Why one name covers several powders
Three variables sit behind the name magnesium bisglycinate: how much water the powder carries, how the powder is presented, and whether a second magnesium source is in the drum. The magnesium percentage reflects all three at once, so it cannot explain them. A hydrate at 12.0% magnesium and an anhydrous chelate at 14.1% are both the 1:2 chelate, but they are different products with different fill weights.
The hydrate window adds a second layer. The catalog covers 8.0–14.0% water, which is wider than a single stoichiometric hydrate; two released lots can sit at different points in that window and still be the same grade. The grade is the pair of results on the certificate, not the word “hydrate” on its own.
How the grades compare
| Grade | Magnesium | Water | Fits | Watch |
|---|---|---|---|---|
| Anhydrous chelate | 13.5–14.2% | Separate moisture limit; not the hydrate window | Capsules and tablets with a tight fill | Hygroscopic; confirm the pack and the in-use period |
| Hydrate, catalog grade | 11.0–12.5% | 8.0–14.0% loss on drying | Capsules, tablets, sticks and blends | Fill weight follows the lot result |
| Monohydrate reference | About 12.8% | About 9.5% | Reference point, not a catalog grade | Magnesium above the catalog ceiling |
| Dihydrate reference | About 11.7% | About 17.3% | Reference point, not a catalog grade | Water above the catalog window |
| Buffered blend | Often above 14% | Varies with the blend | Projects that need a higher magnesium figure | Not a single chelate; the label names both sources |
| Granulated hydrate | Same as the base grade | Same as the base grade | Tablets and sachets that need flow | Granulation aids belong in the specification |
| Milled hydrate | Same as the base grade | Same as the base grade | Capsules and suspensions | Dust, caking and blend segregation |
The monohydrate and dihydrate rows are reference points from the formula, not products on this catalog page. They show why the hydrate window is broad: a monohydrate sits near 12.8% magnesium and 9.5% water, while a dihydrate sits near 11.7% magnesium and 17.3% water. The catalog hydrate does not promise either formula exactly; it promises a magnesium result and a water result inside the two ranges.
What changes in the drum
The hydrate is a white to off-white powder, soluble in water to a clear or slightly opalescent solution. Its catalog particle size is ≥95% through 80 mesh, finer than the 40 mesh of the anhydrous grade, so a capsule blend may flow differently and a tablet blend may need granulation. Bulk density is not set in the catalog for this grade; ask for the measured value on the lot rather than assuming it from the mesh.
Water is part of the product, not an impurity to be removed. A powder at the top of the water window carries less chelate per kilogram than one at the bottom, so the same volume of powder delivers less magnesium. Drying a hydrate lot to raise its magnesium percentage is not a correction; it changes the grade and should be handled as a new specification. The powder is hygroscopic in the open, and caking is the visible result of moisture pickup.
What changes in the finished product
For capsules, fill weight is the constraint. At 11.75% magnesium, a 500 mg capsule carries about 59 mg of elemental magnesium, so a 100 mg label dose takes two capsules before excipients. At the bottom of the range, 11.0%, the same 100 mg takes 909 mg of powder; at the top, 12.5%, it takes 800 mg. The capsule count can change at the edge of the grade even though the specification has not changed.
For tablets, the 80 mesh powder may need granulation to run on the press, and the granulated grade must declare any granulation aid. For sticks and drink mixes, the hydrate dissolves readily; a 200 mg magnesium dose is about 1.6–1.8 g of powder, which is a visible part of a stick's fill weight. For gummies and chews, the water the hydrate brings is part of the matrix's water activity, and the process temperature has to be checked against the glycine in the formula.
None of these decisions is made by the certificate. Only a bench trial with the shipping grade shows the flow, the taste and the fill.
What to write into the specification
- “Magnesium bisglycinate hydrate, 1:2 magnesium–glycine chelate, CAS 14783-68-7.”
- “Magnesium 11.0–12.5% by complexometric titration, as-is.”
- “Loss on drying 8.0–14.0%; the hydrate state stated on the COA and the TDS.”
- “Glycine by HPLC; Mg : glycine ratio 1 : 2 molar.”
- “Appearance white to off-white; particle size ≥95% through 80 mesh.”
- “Heavy metals and microbiology as listed on the product specification.”
- “No undeclared magnesium source; an oxide screen on request, with its detection limit.”
A line that says only “magnesium glycinate 12%” leaves the water, the ratio and the physical form open. The grade table is useful only when the certificate repeats the same definitions.
When another grade is the better buy
If the capsule fill is already tight, the anhydrous grade earns its place because it carries more magnesium per milligram of powder. If the label names the anhydrous chelate, the hydrate is not a drop-in, even when both are inside their magnesium ranges. If the project needs a higher magnesium figure than the chelate can carry, a buffered blend may be the answer, but the label then has to name the second magnesium source.
Granulation is not an upgrade for a capsule blend that already flows, and milling finer will not help a tablet blend that needs density. A grade should answer a constraint that the dosage form really has. The hydrate product page carries the catalog specification; the anhydrous grade has its own page; the water and fill arithmetic is set out on the anhydrous versus hydrate page; the methods are in the methods library; the release process is on the quality page.
In this document
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation