02.1 Lactate vs gluconate

Ferrous lactate vs ferrous gluconate: elemental iron, solubility and the fill

Technical document 02.1 · Reviewed 2026-11-19 · Ferrous Lactate

On this page
  1. The iron figure is the first difference
  2. Solubility and the solution
  3. What the difference does to the fill
  4. Oxidation is common to both, with different timing
  5. The label and the ingredient name
  6. When to choose which

Ferrous lactate carries 23.0–24.5% elemental iron and ferrous gluconate 11.8–12.5%, so a label claim takes roughly half as much lactate as gluconate. Both are water-soluble ferrous salts with acidic solutions, and both oxidise. The choice turns on the iron figure, the fill weight, the colour and taste the matrix can carry, and the ingredient name the label must use.

In one line

Lactate carries about 24% iron and gluconate about 12%, so the same claim takes roughly half the salt mass, and the fill, the solution and the label follow from that.

The iron figure is the first difference

Ferrous lactate is C6H10FeO6 at 233.98 g/mol, 23.87% iron in theory and 23.0–24.5% in the catalogue. Ferrous gluconate is C12H22FeO14·2H2O at 482.17 g/mol, 11.58% iron as the dihydrate and 11.8–12.5% on the dried basis. The gluconate is the larger molecule: two lactate-type ligands and two water molecules around the same ferrous ion, so the iron is a smaller share of the mass.

Ferrous lactate and ferrous gluconate side by side
PropertyFerrous lactateFerrous gluconate
FormulaC6H10FeO6C12H22FeO14·2H2O
Molar mass233.98482.17
Iron, catalogue23.0–24.5%11.8–12.5% (dried basis)
Iron, theory23.87%11.58% as the dihydrate
Loss on drying≤1.0%≤8.0%
ColourGreenish-whiteGreyish-yellow to greenish-yellow
Water solubilitySoluble; acidic solutionSoluble; pH 3.0–5.0 at 5%
Catalogue mesh≥95% through 40 mesh≥95% through 80 mesh

The two iron windows do not overlap: no gluconate lot meets the lactate figure, and no anhydrous lactate lot meets the gluconate window. That is the salt, not the purity, and the names cannot be swapped on a purchase order without recalculating the fill.

Solubility and the solution

Both salts dissolve in water, and both give acidic solutions, so solubility does not separate them in the way it separates a soluble salt from ferrous fumarate. The practical differences are the dissolved solids at a given iron concentration, the colour and the acid load. A lactate solution carries less organic mass for the same iron, which matters in a concentrated stock or a small stick pack.

Both solutions darken towards yellow-brown as the ferrous ion oxidises, and both can throw a basic ferric precipitate if the pH rises. The gluconate catalogue sets pH 3.0–5.0 at 5%; the lactate catalogue does not, so ask for a pH and measure it in your own vehicle if the matrix is pH-sensitive.

Colour is a practical difference. The gluconate powder is already greyish-yellow, while the lactate is greenish-white, so the same brown shift is easier to read against the lactate, and a cast matters in a pale drink or a white tablet.

What the difference does to the fill

At the catalogue midpoints, 1 mg of iron needs 4.21 mg of lactate and 8.23 mg of gluconate. The ratio is about 0.51, and it holds across the claim range, so the lactate fill is roughly half the gluconate fill for the same declared iron.

Salt mass for a label claim · calculated at the catalogue windows
Iron claimFerrous lactate 23.0–24.5%Ferrous gluconate 11.8–12.5%
10 mg41–43 mg80–85 mg
14 mg57–61 mg112–119 mg
18 mg73–78 mg144–153 mg
20 mg82–87 mg160–169 mg
30 mg122–130 mg240–254 mg

A 500 mg capsule filled with lactate delivers 115–122.5 mg of iron; the same fill of gluconate delivers 59–62.5 mg. For a 20 mg claim the lactate needs about 85 mg of powder and the gluconate about 165 mg, so the lactate leaves more room in the capsule for a second active, and the gluconate asks for about twice the fill or a lower dose.

In a tablet, both are fine powders that may need granulation, and the granulating aid adds mass that carries no iron. The gluconate's higher loss-on-drying limit also puts more water in the fill, which matters for dry granulation.

Oxidation is common to both, with different timing

Both salts are ferrous and both oxidise, so the choice is not between a stable salt and an unstable one. The lactate's tighter moisture limit leaves a smaller reservoir of water to start with; the gluconate's water is bound in the crystal, but drying or a failed pack can move it. In a dry blend, the lactate's 1.0% limit is the easier specification to hold, and the gluconate's 8.0% limit allows a wider moisture window.

In solution, both need low dissolved oxygen, an acidic pH and protection from light. The gluconate's larger organic load and its stated pH window belong in the matrix trial. Neither salt should be called stable without the pack, the matrix and the time.

The ferrous ion is a redox-active metal, and a blend that carries a sensitive oil, a vitamin or a pigment beside either salt can discolour. The salt choice changes the mass of iron per gram of blend, and so the size of that effect.

The label and the ingredient name

The label names the salt, not the element: “ferrous lactate” and “ferrous gluconate” are different ingredient names, and the elemental iron figure is the arithmetic that follows. A switch from one to the other is a new ingredient declaration, a new quantitative ingredient statement and, in a supplement, a new Supplement Facts line.

Regulatory status is a separate file. In the EU, the permitted forms for food supplements are listed in Annex II of Directive 2002/46/EC, and the buyer's team checks the current text; in the US, the dietary-supplement route turns on the ingredient's basis, and the label and the claim are reviewed separately. The additive route is yet another file; ferrous lactate has a colour-retention use in some markets, where the limit is written as total iron per kilogram of food rather than as milligrams of salt.

The hydrate state belongs on the specification, and the label should match it: a gluconate dihydrate and an anhydrous lactate are different declarations.

When to choose which

Choose the lactate when the fill is tight, when the label can take a paler powder, and when the formula wants a smaller mass of salt for the same iron. Choose the gluconate when the process and the label are already built around it, when its dihydrate is the qualification basis, or when the market file names it.

Neither is a drop-in for the other. The mass changes by about a factor of two, the ingredient name changes, and the moisture and pH windows change. A switch needs a new specification, a new fill weight, a matrix trial and a label check.

This page is the level-four companion to the grades page. The catalogue line is on the ferrous lactate product page; the other salt is on the ferrous gluconate page; the chelate option is on the iron bisglycinate page; the analytical methods are in the methods library; the release workflow is on the quality page.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation