01 COA & batch testing

What the COA for ferrous lactate actually contains

Technical document 01 · Reviewed 2026-11-19 · Ferrous Lactate

On this page
  1. The certificate as a test report
  2. The anhydrous salt, the basis and the hydrate
  3. Release limit versus batch result
  4. What moves between batches
  5. When to send a lot to a second laboratory
  6. What to compare between suppliers

The certificate for a ferrous lactate lot reports appearance, identification, iron by complexometric titration, the assay on its stated basis, loss on drying, the heavy-metal panel, microbiology and particle size. The catalog limits are 96.0–101.0% assay and 23.0–24.5% iron, with loss on drying not more than 1.0%. The batch COA is the document that confirms a particular pouch or drum, and the hydrate state is the first thing it has to settle.

In one line

The iron figure and the assay are two views of one salt: the certificate is auditable only when the hydrate, the method and the loss on drying sit beside them.

The certificate as a test report

A certificate is auditable when every row can be repeated. That needs three things per line: what was measured, which method produced the number, and which limit the lot was released against. The header should name the salt as anhydrous ferrous lactate, give the CAS number 5905-52-2, and identify the lot and the pack.

Identity, assay, moisture and physical limits · ferrous lactate
ParameterMethodRelease limit
AppearanceVisualGreenish-white powder
IdentificationFerrous reaction, infrared spectrum and titrationConforms to the reference
AssayComplexometric titration96.0–101.0%
Iron (Fe)Complexometric titration23.0–24.5%
Loss on dryingGravimetric≤1.0%
Heavy metalsICP-MSPb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg
MicrobiologyPlate count and absence testsAPC ≤1,000 cfu/g · yeast and mould ≤100 cfu/g · E. coli and Salmonella absent
Particle sizeSieve analysis≥95% through 40 mesh

The appearance line is the only one a reader can check without an instrument, and it is the first that moves when a lot oxidises. It belongs on the sheet even though it is not a number.

The anhydrous salt, the basis and the hydrate

The formula is C6H10FeO6 and the molar mass is 233.98 g/mol, so the theoretical iron fraction of the anhydrous salt is 23.87%. The catalog window of 23.0–24.5% brackets that figure, which is what an anhydrous grade should do. The loss-on-drying limit of 1.0% is part of the same statement: a powder that carries 13% or 19% water is a hydrate, and its iron figure falls to about 20.7% or 19.4%.

That is why the hydrate has to be named. Commercial ferrous lactate is often sold as a dihydrate or a trihydrate under the same CAS number, and a certificate that reports 19–20% iron is describing a different specification, with more mass per milligram of iron. Ask which one the quotation covers before comparing iron figures.

Because the loss on drying is held to 1.0%, the as-is and dried-basis figures sit within about one point of each other on this grade; the basis still has to be printed. An assay of 96.0% of the salt works out to 22.9% iron by the formula, a tenth below the iron floor; at 101.0% it works out to 24.1%. The two windows are close but not identical, and the small gap is method and basis. That is why both lines belong on the sheet, each with its own method.

Release limit versus batch result

A limit is the boundary the lot was released against; a result is what the laboratory measured. Put both in the row with the method next to them. A column that repeats the range has not reported a measurement.

What the result column should contain
ParameterRelease limitResult column
Assay96.0–101.0%The measured percentage and the basis it is reported on
Iron23.0–24.5%The measured percentage, with the titration named
Loss on drying≤1.0%The measured percentage and the drying conditions
Ferric ironAgreed limitTotal iron by ICP-OES minus ferrous iron by a redox titration
Heavy metalsPer elementA figure in mg/kg for each element, with the detection limit
MicrobiologyCounts and absenceThe count and the absence statement for the lot
Particle size≥95% through 40 meshThe measured percentage through the sieve

The ferric line is the one the catalog does not set. A complexometric titration binds iron in either oxidation state, so the iron result counts the total and does not show how much of it is still ferrous. Some monographs carry a separate iron(III) limit, for example not more than 0.6% in the JECFA ferrous lactate monograph as of this review. If the application is oxidation-sensitive, agree a ferric limit for this grade; a total-iron window does not report the thing that changes.

Contaminant lines need detection limits. “Pb: below 0.5 mg/kg” says what the method could see; a bare “Pb: passes” says nothing that can be compared with another laboratory. The catalog limits are per ingredient; the finished-product calculation is a separate step.

What moves between batches

Iron and assay move with the reaction, the crystallisation and the drying step. On an anhydrous grade, water pickup at the surface is the moisture risk: the as-is figure falls and the powder cakes in the pouch.

Colour is the least quantitative line. Greenish-white is the catalog description; a yellow-brown or reddish cast points to ferric iron, and the assay can still pass. Read colour as a prompt to pull the batch record, not as a rejection on its own.

Mesh moves with milling and sieving. A lot at the coarse end of “≥95% through 40 mesh” flows differently in a capsule machine from one that is almost all through, and the single percentage hides that spread.

When to send a lot to a second laboratory

Book an outside test when the source is new, when the lot is the first into a regulated market, when the certificate has to prove a form it does not name, or when a result is disputed. The panel: ferrous iron by a redox titration and total iron by ICP-OES on the same sample and the same basis, infrared identity against a named reference, loss on drying, ICP-MS for the heavy-metal panel, and microbiology.

Ask the laboratory to state the detection limit and the basis for every line, and send the retained sample, the supplier's certificate and your specification together. A referee result without the lot code proves nothing about the drum in the warehouse. The methods library explains what each technique can and cannot show.

What to compare between suppliers

Six lines to compare between two ferrous lactate certificates
LineWhat to askWhy it matters
Form and hydrateAnhydrous or hydrate named, with the CAS numberThe hydrate sets the iron figure per gram
IronResult, method and basis19% and 24% iron are not the same powder
AssayResult and basisTwo figures for one salt have to agree
Loss on dryingResult and conditionsDefines the basis and predicts caking
Ferric ironTotal iron minus ferrous ironA total-iron window hides oxidation
TraceabilityLot code on certificate, pack and retained sampleAn accurate certificate can cover another drum

Compare the six lines, not the two iron percentages. The catalog specification is on the ferrous lactate product page; the salt form and its consequences are on the grades page; the ferrous-versus-ferric evidence is on the identity page; release practice is described on the quality page.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation