Ferrous lactate grades: anhydrous, hydrate and granulated
Ferrous lactate is sold in more than one solid form, and the differences are not cosmetic. The catalog grade is the anhydrous salt at 23.0–24.5% iron and loss on drying not more than 1.0%; the dihydrate and trihydrate carry about 20.7% and 19.4% iron under the same CAS number, and a granulated powder is a process variant of the anhydrous material. The form decides the mass per milligram of iron before it decides anything else.
The hydrate is the grade question: the same CAS number covers salts that differ by up to about 19% water, and the iron figure per gram follows the water.
A grade is a hydrate and a particle, not a new molecule
Every ferrous lactate grade is the same anion and the same ferrous ion. What changes is how much water is bound in the crystal and how the powder has been milled or granulated. The molecular formula of the anhydrous salt is C6H10FeO6; a hydrate adds water to the formula without changing the iron-lactate pair.
That makes the hydrate state a specification decision with an arithmetic consequence. Water is mass that carries no iron, so the iron percentage falls as the hydrate rises. It also changes the loss-on-drying result, the flow of the powder and the quantity the formulator weighs for a declared iron dose.
The catalog material is anhydrous. Ferrous lactate is often traded as a hydrate, and some monographs are written around that: the JECFA monograph, as of this review, allows up to 18% loss on drying and sets a separate iron(III) limit. A certificate inside that monograph can still describe a hydrate. The iron figure and the loss on drying are what tell the two apart.
The forms side by side
| Form | Formula | Molar mass | Iron | Water |
|---|---|---|---|---|
| Anhydrous (catalog) | C6H10FeO6 | 233.98 | 23.9% theoretical | None bound |
| Dihydrate | C6H10FeO6·2H2O | 270.01 | 20.7% theoretical | 13.3% |
| Trihydrate | C6H10FeO6·3H2O | 288.03 | 19.4% theoretical | 18.8% |
| Granulated anhydrous | As anhydrous | 233.98 | 23.9% theoretical | None bound |
The theoretical figures are arithmetic from the formula, not batch results. The catalog window of 23.0–24.5% iron can only be met by the anhydrous solid, because the dihydrate and the trihydrate cannot reach it even at 100% purity. A lot at 19–21% iron is therefore a hydrate or a blend, and the quotation has to say which.
Colour, solubility and the 40 mesh line
The anhydrous powder is greenish-white. The hydrate and the anhydrous form are both pale solids, so colour is not a reliable way to tell them apart; the iron figure and the loss on drying are. A yellow-brown cast is a ferric signal in either form.
Both forms dissolve in water, and both solutions are acidic and oxidise on standing. Solubility is not the dividing line between the grades; the dividing line is water content and particle size. The catalog grade is ≥95% through 40 mesh, and granulation is available on request where dust and flow matter. Granulation does not change the iron figure, but it changes the bulk density, the flow and the fill-weight consistency on a capsule machine.
Particle size is also where a specification can be met on paper and missed in the plant. A single “≥95% through 40 mesh” result does not describe the coarse tail, and the tail decides how the powder runs.
What the form does to the fill
The claim is written as elemental iron; the weigh-up uses the salt. At the catalog midpoint of 23.75% iron, 1 mg of iron needs 4.21 mg of anhydrous ferrous lactate. At the trihydrate's theoretical 19.39%, the same milligram needs 5.16 mg of salt. The hydrate asks for about 23% more mass for the same claim.
| Iron claim | Anhydrous 23.0–24.5% | Trihydrate 19.4% |
|---|---|---|
| 10 mg | 41–43 mg | 52 mg |
| 14 mg | 57–61 mg | 72 mg |
| 18 mg | 73–78 mg | 93 mg |
| 20 mg | 82–87 mg | 103 mg |
| 30 mg | 122–130 mg | 155 mg |
A 500 mg capsule filled with the anhydrous grade delivers 115–122.5 mg of iron; the same fill of trihydrate delivers about 97 mg. Those are arithmetic, not fill-weight guarantees; the press trial and the batch certificate decide the final figure. The arithmetic is still the reason a form switch is a new formulation, not a purchasing substitution.
A tablet adds compression. The anhydrous powder is fine and needs a binder and a lubricant, and granulation is the usual route when it will not run; the granulating aid then has to be declared. A stick or a drink mix takes either form, because both dissolve, but the hydrate contributes water to a powder blend that is meant to be dry.
How to write the specification
- “Ferrous lactate, anhydrous, C6H10FeO6, CAS 5905-52-2.”
- “Assay 96.0–101.0% by complexometric titration, with the basis stated.”
- “Iron 23.0–24.5%; theoretical for the anhydrous salt is 23.87%.”
- “Loss on drying ≤1.0% (gravimetric); state the drying conditions on the certificate.”
- “Identification: ferrous reaction plus infrared comparison with a named reference.”
- “≥95% through 40 mesh; granulated on request.”
- “Heavy metals and microbiology as the catalog; ferric limit to be agreed.”
When a different form is the right purchase
The hydrate is the right purchase when the process is built on it, the higher mass per dose has been accepted, and the certificate is written as a hydrate. It is the wrong purchase when the label claim has to fit a small capsule or when the specification says anhydrous: the iron figure and the fill weight both move.
The anhydrous grade is the wrong choice when the process needs a coarse, free-flowing granule and the milled powder will not run; that is a granulation order, not a different salt. No ferrous lactate grade is the right answer when the label must name a different salt. The comparison with ferrous gluconate is on the level-four page; ferrous gluconate is covered on its product page, and the chelate option on the iron bisglycinate page.
Name the form, the iron figure and the mesh on the purchase order. The product hub carries the catalog line; the COA page shows how the hydrate and the basis are reported; the stability page covers what the water does in storage.
In this document
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation