01 COA & batch testing

What the COA for copper gluconate actually contains

Technical document 01 · Reviewed 2026-11-19 · Copper Gluconate

On this page
  1. Reading the certificate
  2. Assay, copper and the water between them
  3. Release limit versus batch result
  4. What moves between batches
  5. When to order an outside test
  6. What to compare between suppliers

The certificate for a copper gluconate lot reports appearance, identification by infrared spectrum and titration, the salt assay by complexometric titration, elemental copper, water by Karl Fischer, the heavy-metal panel, microbiology and particle size. Each line needs the method, the release limit and the measured result. The limits below are the catalog specification; the batch COA is what confirms a particular pack.

In one line

Copper gluconate is audited on two figures at once: the salt assay and the elemental copper, with the gluconate identity and the water result beside them.

Reading the certificate

A certificate is only as good as the trail it leaves: each line should stand on its own. Every parameter should show the measurement, the method behind it and the limit used at release. A row that says only “conforms” asks for trust without showing the evidence.

Identity, assay, water and contaminants · copper gluconate
ParameterMethodRelease limit
AppearanceVisualBlue-green, free-flowing powder
IdentificationInfrared spectrum and titrationConforms to the reference
Assay (copper gluconate)Complexometric titration98.0–102.0%
Copper (Cu)Complexometric titration or ICP-OES13.5–14.5%
WaterKarl Fischer≤1.0%
Heavy metalsICP-MSPb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg
MicrobiologyPlate count and absence testsAPC ≤1,000 cfu/g; yeast and mould ≤100 cfu/g; E. coli and Salmonella absent
Particle sizeSieve analysis≥95% through 40 mesh

Assay, copper and the water between them

Copper gluconate is C12H22CuO14, with a molar mass of about 453.84 g/mol. Copper accounts for 63.55 of that mass, so the theoretical copper content is 63.55 ÷ 453.84 = 14.0%. The reciprocal, 7.14, converts a copper result into salt: a measured 14.0% Cu corresponds to about 100% copper gluconate, and the catalog range of 13.5–14.5% corresponds to about 96.4–103.6% salt.

That arithmetic is the first audit check. If a certificate reports an assay of 101.0% and a copper result of 12.0%, the pair cannot both describe the same powder: 12.0% × 7.14 = 85.7% salt, not 101%. The two figures should be consistent through that factor; a large mismatch is a question for the laboratory. Ask which result was measured and which was calculated.

The water result is the second check. The catalog allows ≤1.0% by Karl Fischer. With that ceiling the difference between an as-is and a dried basis is at most about one percentage point, but it is not zero, and the certificate should name the basis it used.

The identity row has two halves. The infrared spectrum shows the gluconate ligand; the titration shows copper. A copper reaction on its own would also be positive for copper sulfate or copper oxide, so the ligand evidence is what makes the salt name defensible. The certificate should name the reference spectrum it was compared with.

Release limit versus batch result

The limit is the acceptance boundary; the result is the number the laboratory obtained. They belong in separate columns, with the method alongside. If the result column simply repeats the range, it records the gate rather than the measurement.

The result column, line by line
ParameterRelease limitResult column
Assay98.0–102.0%A measured percentage, with the basis named
Copper13.5–14.5%A measured percentage, with the method named
Water≤1.0%A measured percentage
Heavy metalsPer elementA measured figure in mg/kg for each element
MicrobiologyCounts and absenceThe count and the absence statement for the lot
Particle size≥95% through 40 meshThe measured percentage through the sieve

“Passes specification” is a verdict, and the reader should be able to reconstruct it from the figures. Heavy metals need a number for each element rather than one total. Microbiology needs a count, an absence statement and the sample size. “Heavy metals: passed” does not say which element was tested or against what limit.

What moves between batches

Crystallisation and drying move the assay and the copper figure together, because the assay is normally calculated from the copper titration. A lot that is low on both is a lower-purity or diluted salt. A large mismatch between the two figures points to a calculation or basis error, not to a second component.

Water moves with the drying step and the pack. Copper gluconate is hygroscopic, and a drum that has been opened repeatedly can gain moisture after release; the powder may cake and the blue-green colour may darken or fade. That is a storage change rather than a manufacturing defect, but it is a reason to keep the original pack closed and to record the date of opening.

Particle size moves with the mill and the sieve. The 40 mesh line is set at finishing, so a mill or sieve change can move it while the chemistry stays the same. Colour is the least quantitative line: blue-green covers a range, and moisture or a hot drying step can shift it while the assay remains inside the window.

When to order an outside test

An outside test is worth ordering for a new source, a first regulated shipment, an identity claim the certificate does not establish, or a result in dispute. The useful panel is targeted, not a full repeat of the certificate: complexometric titration for the assay and copper, ICP-OES for copper, Karl Fischer for water, ICP-MS for the heavy-metal panel, microbiology, and an infrared spectrum against a gluconate reference.

Add X-ray diffraction if a crystalline copper salt such as sulfate or oxide is suspected, a sulfate test if the copper figure is high, and a glucose or maltodextrin screen if the assay and copper are both low. Require the detection limit for every screen. Without a limit, “not detected” describes the method, not the powder.

Chain of custody matters. The tested sample and the retained sample should be the same, and the report should carry the lot code. For a contested result, send the referee the retained sample, the certificate and the specification, and ask for the discriminating tests rather than another assay.

What to compare between suppliers

Compare six lines: the salt name and CAS number; the assay with its basis; the copper result and the method; the identity tests with the reference named; water; and the contaminant, microbiology and particle-size results. Two quotations that agree on copper but differ on the ligand evidence or the basis are not describing the same powder.

Traceability is the next layer: the manufacturer, the copper source, the drying step and the link between the certificate and the pack. The catalog specification is on the copper gluconate product page. The identity page shows the tests that separate the salt from other copper sources; the compliance page covers the market conditions; the complexometric method note describes the titration; the ICP-MS note covers the heavy-metal panel; the quality page sets out the release workflow.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation