06 Identity & adulteration

How to prove a copper gluconate lot is the named salt

Technical document 06 · Reviewed 2026-11-19 · Copper Gluconate

On this page
  1. The four identity layers
  2. The copper ratio: proving the salt
  3. X-ray diffraction and the solid state
  4. What adulteration looks like
  5. Writing identity into the specification
  6. Five questions to put to a supplier

A copper gluconate lot is the named salt when four lines agree: the document names copper gluconate and CAS 527-09-3, the infrared spectrum shows the gluconate ligand, the complexometric copper result sits at 13.5–14.5%, and the assay, water and impurity results close the mass balance. The copper figure alone cannot separate copper gluconate from copper sulfate, copper oxide or a dilution. The ligand is the second half of the identity.

In one line

The salt is proved by agreement, not by one number: the gluconate spectrum, the copper figure and the water result must line up under the same CAS number.

The four identity layers

A certificate may name the right material without proving it. The four layers are independent checks; a supplier who supplies only the first has shown the label, not the material.

Four layers of copper gluconate identity
LayerQuestionTestWhat it proves
DocumentIs the salt named?Name, CAS number, formulaPaperwork only
LigandIs the anion gluconate?Infrared spectrum and gluconate reactionThe gluconate
MetalIs the copper figure right?Complexometric titration or ICP-OESThe copper load
Mass balanceIs it diluted?Assay, water, residue and impuritiesConsistency of the numbers

The copper ratio: proving the salt

Copper gluconate has one copper ion and two gluconate anions. The formula is C12H22CuO14 and the molar mass about 453.84 g/mol, so the theoretical copper content is 63.55 ÷ 453.84 = 14.0%. The catalog range of 13.5–14.5% is consistent with that formula. The reciprocal, 7.14, converts copper into salt.

A copper result below 13.5% means a diluted salt or a copper source with a lower copper fraction; the calculated assay will follow it down. A result above 14.5% points to a copper source with a higher fraction, such as sulfate or oxide. The ligand test decides which, because the copper figure alone can be blended to any target.

The solution pH is a supporting check. The catalog describes a slightly acidic solution; a strongly acidic reading can point to residual gluconic acid or a sulfate, and an alkaline reading can point to another copper salt or an additive. pH is not a quantitative identity test, so it is read with the titration and the spectrum.

X-ray diffraction and the solid state

X-ray diffraction answers a solid-state question: is the powder crystalline, and does its pattern match a reference? Copper gluconate is crystalline, and a pattern that matches the reference supports the salt form. A crystalline copper sulfate or copper oxide has a different pattern, so XRD can screen for those adulterants when they are present as a separate phase.

XRD is not a purity test, and it says nothing about the ligand or the copper level. An amorphous diluent can be invisible to it, and a small crystalline impurity can sit below the detection limit. A “match” is only useful with the reference pattern and the detection limit attached.

For a disputed lot, XRD plus infrared plus copper plus the mass balance is stronger than any one of them. XRD is not routine at release here; “XRD conforms” with no pattern and no reference adds little.

What adulteration looks like

Common copper gluconate substitutions and the signals
AdulterantWhat it doesSignalTest
Glucose or maltodextrinDilutes the salt; lowers assay and copperBoth figures low; residue on ignitionCopper, assay, FTIR, water
Copper sulfateRaises copper; adds sulfateCopper above 14.5%; sulfate positiveSulfate test, XRD, ICP-OES
Copper oxideRaises copper; insolubleCopper high; acid-insoluble residueXRD, solubility, residue
Copper citrateDifferent ligand; copper can be closeInfrared differs; citrate reactionFTIR, citrate test
Excess gluconic acidLowers copper and pHpH low; copper lowpH, titration
WaterLowers the as-is assay; discoloursWater high; colour changeKarl Fischer, appearance

Colour carries the least weight. Blue-green covers a range, and a copper salt or a dye can reproduce it. The stronger signals are the ligand spectrum, the copper figure and the mass balance. Appearance and assay without identity leave the likeliest substitution untested.

Writing identity into the specification

  • “Copper gluconate, CAS 527-09-3, C12H22CuO14.”
  • “Assay 98.0–102.0% by EDTA titration; state the basis.”
  • “Copper 13.5–14.5% by titration or ICP-OES, reported with the method.”
  • “Identification by infrared spectrum against a reference and by copper titration.”
  • “Water ≤1.0% by Karl Fischer; appearance blue-green.”
  • “Particle size ≥95% through 40 mesh; contaminants and microbiology as tabulated.”
  • “No other copper salt or carrier above the agreed limit.”

Five questions to put to a supplier

  1. What copper salt is this lot, and which CAS number does the certificate carry?
  2. Will you send the infrared spectrum with its reference, rather than a bare “conforms”?
  3. How was copper measured, and does the result agree with the assay?
  4. What water result was found, and which basis was used for the assay?
  5. If identity is challenged, will you re-test the retained sample jointly?

Five direct answers amount to an identity file. A single copper percentage does not. The product hub has the catalog specification; the COA page locates each figure on the certificate; the grades page covers the physical options; the level-four comparison covers the chelate; the FTIR note and the complexometric note explain the two tests; the quality page covers release.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation