What the COA for calcium bisglycinate actually contains
The certificate for a calcium bisglycinate lot reports appearance, calcium by complexometric EDTA, glycine identification by infrared spectrum and reaction, loss on drying, pH, particle size, bulk density, the heavy-metal panel and microbiology. Each line should name the test, the method and the release limit used for that lot. The ranges below are the catalog specification; the batch COA reports what a particular pouch or drum actually contains. A calcium result near 21% is not enough on its own, because several calcium salts report a similar figure.
Calcium at about 21% is where the chelate and the citrate meet, so the certificate has to prove the ligand as well as the element.
The certificate as a test report
A certificate becomes useful when it can be read line by line. For each parameter the buyer needs three things: the measurement, the method behind it, and the acceptance boundary used at release.
| Item | Method | Acceptance range |
|---|---|---|
| Appearance | Visual | White to off-white, free-flowing powder |
| Calcium (Ca) | Complexometric EDTA titration | 18.5–23.0% |
| Identification | Infrared spectrum and glycine reaction | Conforms to reference |
| Loss on drying | Gravimetric | ≤5.0% |
| pH (5% suspension) | Potentiometry | 6.0–8.0 |
| Item | Method | Acceptance range |
|---|---|---|
| Particle size | Sieve analysis | ≥95% through 80 mesh |
| Bulk density | Tapped cylinder | 0.50–0.80 g/mL |
| Heavy metals | ICP-MS | Pb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg |
| Microbiology | Plate count and absence tests | APC ≤1,000 cfu/g; yeast and mould ≤100 cfu/g; E. coli and Salmonella absent |
What the calcium and moisture figures measure
Calcium is reported as the element, not as the chelate. The anhydrous formula C4H8CaN2O4 has a formula mass of 188.20, and a 1:2 calcium–glycine chelate carries 21.3% calcium and 79.8% glycine. The catalog window of 18.5–23.0% brackets that figure without pinning the lot to it: water, residual glycine and the reaction conditions all move the calcium result. A number inside the window is a calcium result, not a purity figure and not a ratio.
Loss on drying measures water and volatiles, and the ≤5.0% limit is a ceiling rather than a target. A lot at 4.8% and a lot at 0.6% both pass, but they do not have the same solids content, and the calcium figure as sold moves with that water. The certificate should say that calcium is reported on the material as sold. A calcium result recalculated to a dried basis is higher, and the two bases cannot be compared without the moisture result beside them.
Identification is a presence test: the infrared spectrum and the glycine reaction show that glycine is in the sample, not that it is bound at a 1:2 ratio. The ratio is a separate calculation from calcium and a quantitative glycine result, and it needs a free-glycine figure to be read properly. A certificate that shows glycine only by reaction leaves the chelate identity open.
The gate and the measured result
A release limit marks the boundary a lot had to meet. The batch result is what the laboratory measured. The two sit in separate columns, with the method beside each number. A result column that repeats the specification range has not reported a measurement; it has copied the acceptance range.
Not every line has a numeric range. Appearance, identification and the absence tests are pass or fail lines, and “conforms” is only a result when the reference standard and the method are named. The calcium, loss on drying and pH lines are the ones to read first.
The heavy-metal and microbiological limits are catalog ceilings. The batch COA reports the measured values, and the buyer compares those values with the limit in the destination market as well as with the specification. A lot can meet the catalog ceiling and still fail a customer's tighter arsenic limit, so the purchase specification should carry the tighter figure when one applies.
What moves between batches
Calcium and loss on drying move with the reaction, the washing step and the drying step; pH moves with residual liquor; particle size and bulk density move with milling and granulation. A granulated grade and a milled grade can share a calcium result and behave differently on a capsule filler or a tablet press.
Colour and flow are less quantitative and often more revealing. A cream or tan tint can point to a hot drying step or a trace of iron while the calcium assay still passes; ask for the batch record instead of rejecting on colour. A drift across successive lots — calcium moving to one edge, loss on drying climbing — says more than a single result near a limit.
When to order an outside test
Order an independent test when the source is new, when a lot is the first into a regulated market, when a chelate claim is not proved by the supplier's certificate, or when a result is disputed. The useful panel is narrower than a full repeat: calcium by EDTA, glycine by HPLC with a free-glycine figure, FTIR for coordination, XRD for crystalline calcium salts and free glycine, and ICP-MS for the heavy-metal panel, all on one submitted sample.
Ask the laboratory to state its detection limit for the XRD screen. A “not detected” line without a limit describes the method's sensitivity, not the sample. The glycine assay should identify the column and detector and state its basis, not just give a percentage. When a result is contested, the referee should receive the retained sample, the supplier's certificate and the specification, and the chain of custody should connect the sample tested to the sample retained.
What to compare between suppliers
Six lines make a supplier comparison useful: the form and mesh; the calcium result with its method and basis; the glycine identity and, where available, the glycine and free-glycine results; loss on drying; pH; and the contaminant panel. Two quotations that agree on calcium but diverge on the other five are not describing the same powder.
The second layer is lot traceability. The certificate, the pack and the retained sample should all carry one lot code, and the certificate should say who manufactured the lot and which calcium source and drying step were used. A correct certificate can still belong to a different drum; the lot code rules that out.
The catalog specification is published on the calcium bisglycinate product page. The choice between the bisglycinate and the citrate is set out on the salt comparison page, and the tests that separate the chelate from a blend are on the identity page. The titration is described in the complexometric method note, and the release process is described on the quality page.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation