03 Stability

L-carnitine base is hygroscopic; the pack decides the shelf life

Technical document 03 · Reviewed 2026-11-18 · L-Carnitine

On this page
  1. The dry solid and its one weakness
  2. In solution the risk changes
  3. What actually moves the powder
  4. A stability programme for the pack
  5. Where a formula defeats a good pack
  6. Assigning a shelf life

L-carnitine base is chemically robust as a dry solid; its failure mode is water. The powder picks up moisture from the air, softens and cakes, and the loss-on-drying limit of ≤0.5% is crossed long before the assay moves. What decides the shelf life is therefore the pack — the sealed foil pouch, the drum liner, the dose room — and the discipline of closing that pack after a partial weigh-out. A shelf life is assigned from data on the market pack, not from the molecule.

In one line

The molecule survives the shelf life; the powder does not, unless the pack keeps water out.

The dry solid and its one weakness

The crystalline base has no obvious oxidation pathway and no hydrolysable group, so it can sit in a blend without a special antioxidant. The weakness is physical: water adsorbs on the crystal surface, the surface begins to dissolve, and at high humidity the powder turns from free-flowing crystals into a sticky mass. The material is not chemically degraded, but it can no longer be weighed, blended or filled with any consistency.

The specification reflects that. Loss on drying at ≤0.5% is a tight limit for a hygroscopic solid, and it is a limit on the pack as much as on the dryer. A lot released at 0.3% that sits in an opened pouch for a week in a humid room will not be at 0.3% when it is weighed, and the anhydrous assay will move with it.

In solution the risk changes

The base is freely soluble and close to neutral in water, which is convenient for a liquid and awkward for preservation: a near-neutral, water-rich system with no acid stress is a good place for microorganisms to grow. In an aqueous formula the questions are the preservative system, pH control and the finished-product microbial limit, not the stability of the carnitine itself.

The acetyl form is different, because it carries an ester. An ester can hydrolyse, and the rate rises with pH and temperature, so an acetyl-L-carnitine beverage is a stability study in its own right while a carnitine base beverage is mainly a preservation study. The base has no such bond to break.

What actually moves the powder

Failure factors for L-carnitine base in a finished pack
FactorMechanismWhat you seeControl
Humidity in the dose roomWater adsorption on the crystal surfaceWeight gain, caking, bridging in the hopperDehumidified weighing and filling area
Open pack between weigh-outsUnsealed liner admits room airLumps in the pouch, LOD driftReseal, desiccant where agreed, use the opened pack first
Heat during drying or granulationSurface water redistributes; colour shiftsOff-white to cream tint, harder lumpsControl the drying end-point, not only the peak temperature
pH in a liquid matrixShifts the zwitterion and the tasteAcid or alkaline drift, microbial growthBuffer and preservative system tested on the finished product
Reducing sugars in the blendBrowning reactions elsewhere in the matrixColour development in the stick or tabletTest the blend, not the ingredient alone
Compaction and fine millingMore surface, more contact pointsHard caking in a compressed or milled powderGranulate, or specify the mesh the process can handle

One note belongs under the sugar row. Carnitine's nitrogen is quaternary and carries no hydrogen, so it does not start the browning reaction the way a primary amine does. A carnitine stick that darkens is reacting around the carnitine, not with it, and the fix belongs to the formula.

A stability programme for the pack

Run the study on the pack that will be sold, not on a lab jar. The usual conditions are 25 °C/60% relative humidity for the long term and 40 °C/75% for the accelerated arm, with time points at 0, 3, 6, 12, 24 and 36 months, and a glass-sealed control to separate the pack from time. Add two arms a food-ingredient study needs: an open-pack arm, where the pouch is opened, folded and stored as a customer would, and a cycling arm between the two conditions.

Test appearance, loss on drying, assay and specific rotation at every point, and add particle size or flow where the powder is filled on a machine. Microbiology belongs at the start and the end, and after any open-pack interval. The conditions are borrowed from pharmaceutical practice because the numbers are comparable between suppliers; they are not a regulatory requirement for a food ingredient.

Where a formula defeats a good pack

A sealed pouch protects the powder until it is opened; the formula and the filling line decide what happens next. Gelatin and HPMC shells both transmit water, and a hygroscopic carrier can pull water into the shell or the film. A stick pack with a high water activity gives the powder a humid microclimate even when the factory air is dry, and an effervescent system adds acid, carbonate and a strong driving force for water uptake.

The dose room is part of the formula. A 40-mesh powder exposed for twenty minutes in a room at 70% relative humidity takes up more water than the same powder exposed for two minutes, and the difference shows up as fill-weight variation rather than as a failed certificate. Granulation, an 80-mesh specification and a dehumidified filling area are the levers, and they are easier to specify at the start than to correct after a caking complaint.

Assigning a shelf life

A shelf life is a statement about a pack, a storage condition and a set of end-of-life limits. It should be written as all three: the pouch or drum, the maximum temperature and humidity, and the limits the product must still meet at the end. The end-of-life limits are agreed with the buyer; a common approach is to hold water and appearance at the release limits and allow the assay a defined margin, but the numbers have to come from the data rather than from habit.

Two clauses prevent most disputes. The first covers the opened pack: reseal, store dry, use within the stated interval, and do not return the remainder to the original lot without a new test. The second separates a date of minimum durability from a re-test date, which is only useful if the buyer can act on it. The catalog does not publish a single shelf life for every destination, because the pack and the climate are not the same in every destination.

The release tests are on the COA page; the packs that carry the moisture barrier are described on the MOQ page; the documentary side is on the compliance page. The base and the tartrate are compared for handling on the base versus tartrate page, the product page carries the specification, and loss on drying is defined in the glossary.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation