06 Identity & adulteration

How we prove an L-carnitine lot is the L form

Technical document 06 · Reviewed 2026-11-18 · L-Carnitine

On this page
  1. Four layers of identity
  2. The enantiomeric ratio
  3. What XRD can and cannot tell you
  4. The substitution routes to check
  5. How to write the specification line
  6. Five questions for a supplier

The L form is proved in layers: the paper trail names the substance, infrared and HPLC confirm that the substance is carnitine, the specific rotation assigns the configuration, and the counter-ion and water confirm which physical form is in the drum. No single test does all four jobs, and an assay result does none of them on its own. A lot that reads 99.5% can still be the wrong enantiomer, a salt rather than the base, or a blend.

In one line

The rotation and the chromatogram prove the configuration; the assay proves only how much material is there.

Four layers of identity

Start with what the document says, then move to what the instrument measures, then to the configuration, then to the form. Each layer answers a different question, and each has a blind spot that the next layer covers.

Identity layers for L-carnitine and what each one misses
LayerQuestionTestBlind spot
RecordWhat is this lot supposed to be?Name, CAS number, lot code, specificationSays nothing about the drum
SubstanceIs it carnitine?Infrared spectrum, HPLC retention and assayCannot separate the enantiomers
ConfigurationIs it the L form?Specific rotation, chiral HPLCWeak on quantity; needs clean optics
FormBase, salt or ester?Counter-ion tests, water, titrationSilent on configuration

The order matters. A buyer who starts with the assay is looking at the one number that is compatible with every failure mode on the list.

The enantiomeric ratio

Specific rotation is how the enantiomeric ratio appears in a polarimeter. The measured rotation is divided by the path length in decimetres and the concentration in g/mL to give the specific figure, and the result is compared with the range for the pure enantiomer. On a 10% solution the reading is small, so the cell, the temperature and the balance all matter; a certificate that prints −30.4° without saying how it was obtained is asking to be believed rather than checked.

The window of −29.0° to −32.0° is a practical gate, not a purity grade. If the pure material reads near the middle of the window, the lower edge corresponds to a few per cent of the D enantiomer in the sample. Two lots can both sit inside the window and differ in enantiomeric composition, which is why the number itself, not only a pass mark, belongs on the certificate.

For a salt there is a second ratio: the stoichiometry. L-carnitine L-tartrate is a 2:1 salt, so a tartrate certificate should be consistent with two carnitine units per tartaric acid unit. A salt that is off that ratio is either a different salt or a blend, and neither is what the label says.

What XRD can and cannot tell you

X-ray diffraction reads the crystal lattice, and carnitine is crystalline, so a diffraction pattern is a genuine fingerprint of the solid form. It is useful for checking that a lot is the same crystal form as the reference, and for catching a different salt or an amorphous or recrystallised material that dissolves and flows differently.

It cannot assign the configuration. The two enantiomers are isostructural, and a physical mixture of L and D crystals gives the pattern of the L crystal, because the lattices are identical. A racemic compound — a distinct crystal containing both enantiomers in the unit cell — can give a different pattern, so XRD may raise a flag; it cannot clear one. The same limitation applies to the infrared identity test: the functional groups are the same in both enantiomers, so the spectrum is too.

Use XRD for the form question and keep it away from the configuration question. A supplier who offers a diffraction pattern as proof of the L form has offered the wrong evidence.

The substitution routes to check

Four routes are worth testing for, and each has a different signature.

The first is the opposite enantiomer. D-carnitine, or a racemic DL mixture, passes an assay and moves the rotation toward zero; only polarimetry or chiral HPLC sees it. The second is another betaine: trimethylglycine or choline is a white, water-soluble powder that can inflate a non-specific nitrogen assay, and a chromatographic method with a proper carnitine standard separates them while a titration may not. The third is a salt sold as the base: the tartrate carries about 68% carnitine, so a carnitine assay run on it reads low, but a seller who quotes the carnitine figure as if it were the powder weight is describing a different material. The fourth is simple dilution with a white carrier, which lowers the assay and usually moves the water or the residue with it.

Each route is caught by a different line on the certificate, which is why the identity page and the COA page have to be read together.

How to write the specification line

A specification that can be enforced names the form, the basis and the configuration in the same breath. A workable line reads: “L-carnitine base, 98.0–102.0% on the anhydrous basis by HPLC; specific rotation −29.0° to −32.0° on a 10% solution; loss on drying ≤0.5%; residue on ignition ≤0.1%; D-carnitine not more than the agreed limit by chiral HPLC.”

Three details make that line enforceable. It says “base”, so a tartrate cannot be delivered against it. It says “anhydrous basis”, so the water correction cannot be applied silently. And it puts the chiral limit in the specification, because a limit that exists only in a conversation does not survive a supplier change.

Where the form is a salt, add the counter-ion and the stoichiometry. Where the material is milled or granulated, add the mesh. The specification is the document the certificate is judged against, so every test on the identity list should appear in it.

Five questions for a supplier

  1. Is the specific rotation measured on this lot, and with which solvent, concentration, temperature and path length?
  2. Which HPLC method and which standard produced the assay, and is the figure on the anhydrous basis?
  3. What is the D-carnitine result, by which chiral method, and what is that method's detection limit?
  4. Is the material the base, the tartrate or the acetyl form, and which counter-ion is present in this lot?
  5. Where was the lot manufactured, and can the batch record for the crystallisation and drying steps be shared under an agreement?

A supplier who can answer all five is selling a specified material. A supplier who answers only the assay has described a white powder.

The certificate those answers should appear on is described on the COA page; the forms are compared on the grade page and on the base versus tartrate page. The product page carries the catalog specification, the separation is explained in the HPLC method note, and assay is defined in the glossary.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation