01 COA & batch testing

What the COA for D-pantothenic acid reports

Technical document 01 · Reviewed 2026-11-20 · Pantothenic Acid

On this page
  1. Reading the certificate line by line
  2. Assay basis, water and pH
  3. Limit, result and what counts as evidence
  4. What changes from lot to lot
  5. Bringing in an outside laboratory
  6. A supplier comparison that works

A pantothenic acid certificate is a lot-specific test report. It should list appearance, HPLC and IR identification, HPLC assay, loss on drying, the pH of a 5% solution, the heavy-metal panel, microbiology and particle size, with the method and the release limit beside each result. The figures below are the catalog specification; the certificate is what confirms a particular pack.

In one line

The free acid is identified by HPLC and IR, and its acidic 5% solution separates it from the salt; the assay needs a stated moisture basis.

Reading the certificate line by line

A certificate is only as useful as its weakest line. For every parameter the reader should be able to see what was tested, how it was tested and the boundary the lot had to meet. A bare “conforms” gives a conclusion with no route to check it.

The identity block leads, because a bad identity result cannot be offset by a high assay. On this product the pH row also carries information about form: an acidic solution is consistent with the free acid, while a pantothenate salt would sit nearer neutral.

Release panel for D-pantothenic acid
TestHow it is runLimit for release
AppearanceVisual inspectionWhite to off-white powder
IdentityHPLC retention plus IR spectrumMatches the reference
AssayHPLC; basis declared98.0–101.0%
WaterGravimetric loss on drying≤5.0%
AcidityPotentiometric pH, 5% solution2.5–3.5
MetalsICP-MS, individual elementsPb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg
MicroTotal plate count plus absence screenAPC ≤1,000 cfu/g; yeast and mould ≤100 cfu/g; E. coli and Salmonella absent
Particle sizeSieve test at 80 mesh≥95% passing

Assay basis, water and pH

The catalog gives 98.0–101.0% by HPLC, but it does not say whether that number is calculated on the powder as received or on the dried solids. The certificate must settle it. Take a lot at 99.0% on the dried basis with 3.0% loss on drying: the as-is figure is 96.0%, and a weigh-up built on 99.0% overstates the active mass by three points.

pH is not a purity measure here; it is a quick form check. The free acid has a carboxyl group, so its 5% solution falls in the 2.5–3.5 window. Calcium or sodium pantothenate would not. A pH value is only comparable when the concentration and temperature accompany it.

Pantothenic acid absorbs weakly in the ultraviolet, which is why the HPLC method needs a declared detection wavelength and a named standard. Retention time by itself is a single data point; the IR spectrum supplies the second.

Limit, result and what counts as evidence

Two different things belong in two different columns: the boundary the lot had to meet, and the value the laboratory actually obtained. Printing the specification range in the result column does not report a measurement.

What a useful result column contains
TestAcceptance boundaryExpected entry
Assay98.0–101.0% by HPLCThe measured percentage, with basis and wavelength
Water≤5.0%The measured loss and the drying condition
Acidity2.5–3.5 at 5%The measured pH and the concentration used
MetalsSeparate limit per elementA figure in mg/kg for each element
Particle size≥95% through 80 meshThe measured percentage passing

A conclusion such as “meets specification” is only useful if the numbers that support it are visible. Micro results need counts and absence statements; metals need one figure per element, not a sum that hides which element is high.

What changes from lot to lot

Water content follows the dryer and the pack. Colour follows the drying history and, on a hygroscopic powder, the time it spent exposed before filling. The 80 mesh result follows the mill and the sieve, so a new mill can move that line while the chemistry is unchanged.

Look at the direction of travel across lots rather than one number near a limit. Rising moisture, a drifting pH or a new shoulder in the chromatogram is a pattern worth asking about. The lot code on the paper should also appear on the pouch, the drum and the retained sample.

Bringing in an outside laboratory

An outside laboratory is worth using for a new source, a first import into a regulated market, a form the supplier's certificate does not establish, or a result in dispute. The panel should be chosen for the question, not copied from the certificate: HPLC with the wavelength stated, IR against a reference, loss on drying, pH, calcium and sodium by ICP-OES, the metal panel and micro.

Where the D-enantiomer is contractual, add specific rotation; IR and an achiral HPLC method cannot tell D from L. Each screen should come with its detection limit, because “not detected” means little without knowing how low the method can see.

A supplier comparison that works

Six lines make a comparison: the form and CAS number; the assay and its basis; the HPLC wavelength and the IR match; moisture and pH; metals and micro; pack and lot code. If two offers agree on the percentage but not on the form or the basis, they are not the same material.

The catalog values are on the pantothenic acid product page. The calcium salt is described on the vitamin B5 page; the identity page covers the form tests; the methods library holds the HPLC and FTIR notes; the quality page explains release.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation