What the COA for choline bitartrate actually contains
The certificate for a choline bitartrate lot reports appearance, identification by IR, assay by titration on the as-is basis, choline by HPLC, loss on drying, pH, particle size, the heavy-metal panel and microbiology. Each row should show the method, the release limit and the result for that lot. The ranges below are the catalog specification; the batch COA is the document that confirms a particular pack. The assay and the choline figure answer different questions and belong side by side.
The bitartrate assay is not the choline dose; the salt, the figure and the basis have to be named together.
The certificate as a release panel
A certificate is auditable when each line carries the test, the method, the release limit and the result. The table is the catalog panel; the certificate repeats it with a result column and a lot code.
| Parameter | Method | Release limit |
|---|---|---|
| Appearance | Visual | White crystalline powder |
| Identification | IR against a reference | Conforms |
| Assay, as-is | Titration (choline) | 96.5–100.5% |
| Choline | HPLC | 40.5–41.5% |
| Loss on drying | Gravimetric | ≤1.0% |
| pH (5% solution) | Potentiometry | 3.0–4.5 |
| Particle size | Sieve analysis | ≥95% through 40 mesh |
| Heavy metals | ICP-MS | Pb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg |
| Microbiology | Plate count and absence tests | APC ≤1,000 cfu/g; yeast and mould ≤100 cfu/g; E. coli and Salmonella absent |
The heavy-metal and microbiology rows are panels, not single results. The certificate should list each element and organism, even when the line reads “absent”; a panel compressed to “metals pass” cannot be compared with a destination limit.
What the titration and the HPLC measure
The titration measures the choline cation, not the tartrate. Choline bitartrate is a 1:1 salt; the quaternary ammonium ion is titrated with a standard acid, commonly perchloric acid in glacial acetic acid, to a potentiometric endpoint. The result is calculated as choline bitartrate using 253.25 g/mol and reported on the as-is basis. It is a salt-equivalent figure, not an anion assay.
The HPLC also measures choline, after separation. Choline has weak ultraviolet absorbance, so the method needs a separation and detector suited to a quaternary ammonium ion; the certificate should name the column, detector and standard. The catalog window of 40.5–41.5% brackets the theoretical 41.1% (104.17/253.25), the figure that matters for dose and label.
Because both methods measure the same cation, they should agree. Convert the titration to choline (assay × 104.17/253.25) and compare it with the HPLC figure. A gap points to a titratable impurity or an HPLC interference; it does not identify the anion. The anion is proven by IR and, where wanted, a tartrate precipitation test. The certificate should state both bases and name the titrant, endpoint and HPLC conditions.
Release limit, batch result and the basis
The release limit is the boundary; the batch result is the measurement. Both belong on the page, in separate columns, with the method beside them. A result column filled with the specification range is a copy of the gate, not a result; “passes specification” is a conclusion the reader should be able to reach from the numbers.
The assay is as-is, and that is not a detail. The same dry material reads higher on a dried basis, so an as-is result must not be compared with a dried-basis limit from another supplier. The loss-on-drying figure sits beside the assay for that reason, and the choline figure should also state its basis; if the certificate leaves it out, ask.
Some lines are pass/fail: appearance and IR. “IR conforms” is meaningful only if the certificate names the reference material and the sample preparation; a spectrum compared with nothing is a picture, not an identity test.
What moves between lots
The reaction and crystallisation set the ratio; drying sets the loss on drying; residual acidity sets pH; milling sets particle size. Because both potency figures measure choline, they should move together. A neutral diluent lowers both; a chloride substitution raises both, but the assay expressed as bitartrate rises faster and usually breaks 100.5% before the choline window does. A small chloride spike can stay inside both windows, which is why the chloride test is the direct check. A gap between the two choline figures points to a method interference or a co-eluting peak, not to the anion.
Moisture is the common drift. A pack left open takes up water, the loss on drying rises, the powder cakes, and the as-is assay falls even though the dry material is unchanged. Colour and odour are less quantitative and often more revealing: a tan tint or an amine note can follow a hot drying step or an impurity while the assay still passes. Ask for the batch record before rejecting on appearance alone.
A trend across lots — loss on drying rising, pH falling, the gap between the two choline figures widening — says more than one result near an edge.
When an outside test earns its place
Order an independent test for a new source, a first shipment into a regulated market, a form claim the certificate does not prove, or a disputed result. The panel is not a repeat: FTIR against a choline bitartrate reference, HPLC for choline, the titration, a chloride test, loss on drying and ICP-MS for the metals, with XRD when a crystalline diluent is suspected.
Ask for the detection or quantification limit for chloride; “not detected” without a limit says something about the method, not the sample. The FTIR report should name the reference standard and the sample preparation, because water broadens the hydroxyl region and can hide the difference between two salts.
An outside laboratory is the sensible referee when a result is contested. Give it the retained sample, the certificate and the specification, and ask for the tests that separate the salts; the sample tested should be the sample retained.
Six lines to compare between suppliers
| Line | What to ask | Why it matters |
|---|---|---|
| Form and CAS | Choline bitartrate, CAS 87-67-2, or another salt? | Other salts carry different choline figures |
| Assay and basis | Titration result, as-is or dried? | As-is and dried figures are not interchangeable |
| Choline and method | HPLC result and detector? | The choline figure drives the dose and the label |
| Moisture and pH | Loss on drying and 5% pH results? | Water and acidity move the powder's behaviour in the blend |
| Particle size | 40 mesh, 80 mesh or granulated? | Flow, segregation and caking differ |
| Identity and chloride | IR reference and chloride result? | A choline figure alone does not prove the bitartrate |
Two quotations that match on assay but diverge on choline, moisture or chloride are not describing the same powder. Lot traceability is the second layer: the lot code should match on the certificate, the pack and the retained sample, and the certificate should name the manufacturer and any blending or repacking.
The catalog limits sit on the choline bitartrate product page. The salt comparison is on the grade page, the identity tests on the identity page, and the release workflow on the quality page. The two methods are described in the HPLC method note and the FTIR method note.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation