06 Identity & adulteration

How we prove a pea peptide lot is hydrolysed pea protein

Technical document 06 · Reviewed 2026-11-19 · Pea Protein Peptides

On this page
  1. Four layers, four questions
  2. The ratios and the nitrogen arithmetic
  3. What X-ray diffraction can and cannot settle
  4. What substitution looks like
  5. Lines the specification must carry
  6. Five questions to put to the supplier

A lot is pea protein peptides when four things agree: the source is pea, the nitrogen figure supports the protein claim with its factor and basis, the HPLC distribution shows the peptide fraction, and the ash and moisture close the mass balance. The peptide percentage on its own is the weakest evidence, because a blend or a non-protein nitrogen source can lift a number without making a peptide.

In one line

A pea peptide lot is what it claims when the source, the peptide distribution, the nitrogen arithmetic and the mass balance agree.

Four layers, four questions

Four layers of pea peptide identity
LayerQuestionTestWhat it proves
DocumentIs the material and source named?Name, base protein, process recordPaperwork only
ProteinDoes the nitrogen match the claim?Kjeldahl, N × 6.25, with the basisThe nitrogen, not the source
PeptideHow much is in peptide form?HPLC distribution against the cut-offThe size fraction
BalanceWhat else is in the powder?Ash, moisture, amino acid profileConsistency of the numbers

The first layer is necessary and never sufficient. The second measures nitrogen, and nitrogen arrives with protein, with free amino acids and with non-protein nitrogen. The third is the layer that separates a hydrolysate from an isolate. The fourth is where a dilution or a salt load shows up.

The ratios and the nitrogen arithmetic

At N × 6.25, an 80.0% protein figure sits on about 12.8% nitrogen. The peptide floor of 70.0% against that protein floor gives a peptide-to-protein ratio of 0.875: at the catalog limits, at least 87.5% of the protein is in peptide form, and the rest is intact protein, free amino acids or material counted differently by the method. If a certificate reports peptide content above protein content, the two figures are not on the same basis or one of them is wrong, and the chromatogram should be read before the lot is accepted.

The ash and moisture limits close the arithmetic. At 80.0% protein, 5.0% ash and 7.0% moisture, 92% of the powder is accounted for, leaving at most about 8% for fat, fibre, sugars and other solids. A lot that reports 80% protein and 5% ash but leaves 20% unaccounted for is either carrying a large carbohydrate fraction or has a nitrogen figure that is not all protein. The protein-to-ash ratio at the limits is 16:1; a much higher ratio with a high protein figure points to a washed isolate base, and a much lower one to neutralisation salts or a dilution.

Free amino acids are the other part of the ratio. Hydrolysis produces some, and they count as nitrogen but not as peptide. Ask for the free amino acid figure or the amino acid profile, and read a large free fraction as a composition fact rather than a defect; it changes the taste and the osmolality, and it belongs in the specification if the formula depends on it.

What X-ray diffraction can and cannot settle

A spray-dried peptide powder is amorphous, so its X-ray diffraction pattern is a broad halo with no sharp reflections. That is consistent with the drying route, and it is not a source test: an isolate, a hydrolysate and a blend of the two can all give the same halo. XRD is useful when a crystalline phase appears — a sugar alcohol carrier, a crystalline amino acid, an inorganic salt or, at a high enough level, a crystalline adulterant such as melamine. The detection limit matters, and a “no crystalline phase” statement without the pattern and the limit adds little.

For identity, the stronger combination is the amino acid profile, the peptide distribution and the mass balance. XRD and FTIR answer the solid-state and functional-group questions, and they are supplementary. The XRD method note sets out the technique; the methods library covers the rest.

What substitution looks like

Substitution routes for pea peptides and the signals
RouteWhat it changesTest that catches it
Non-protein nitrogenKjeldahl up; peptide and amino acid sums unchangedAmino acid profile, melamine by LC-MS/MS
Free amino acid spikePeptide content down; nitrogen up; taste shiftsPeptide distribution, free amino acid analysis
Whey, soy or collagen blendAmino acid pattern moves; foreign protein presentAmino acid profile, ELISA or PCR where the matrix allows
Maltodextrin or starchProtein and peptide down; carbohydrate by difference upMass balance, XRD for crystalline starch
Salt or neutralisation loadAsh high; protein and peptide dilutedAsh, conductivity, mineral panel
Excess waterMoisture above limit; caking; as-is protein downLoss on drying, water activity

The first route is the safety-critical one: melamine and urea raise the nitrogen figure without raising the peptide or amino acid result. The second and third are commercial substitutions that can pass a protein floor while failing the peptide or source claim. The last is the ordinary storage failure that a retained sample catches before a customer does.

Lines the specification must carry

  1. The material, the base protein and the hydrolysis route: pea protein peptides, an enzymatic hydrolysate of pea protein.
  2. Protein, with the factor and basis: ≥80.0% by Kjeldahl, N × 6.25, as-is or dry basis stated.
  3. Peptide content, with the method and the cut-off: ≥70.0% by HPLC distribution.
  4. Ash ≤5.0%, moisture ≤7.0% and ≥95% through 80 mesh, each with its method.
  5. An amino acid profile and a non-protein nitrogen or melamine screen where the risk exists.
  6. The allergen and cross-contact statement for pea and any shared line, and the destination market.

Five questions to put to the supplier

  1. Which factor and basis does the certificate use, and is the raw nitrogen result printed next to the protein figure?
  2. Which HPLC method and molecular-weight cut-off define the peptide content, and can the distribution be provided?
  3. What is the ash result, and how much of it comes from neutralisation?
  4. Has the lot been screened for melamine or another non-protein nitrogen source, and at what detection limit?
  5. Does the retained sample carry the same lot code as the pack, and will the supplier accept a joint re-test?

Five direct answers amount to an identity file; a single protein percentage does not. The product page carries the catalog limits; the COA page maps each figure to its certificate line; the grades page covers the peptide levers; the quality page describes the release file.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation