02.1 Peptides vs isolate

Pea protein peptides vs pea protein isolate: what hydrolysis changes

Technical document 02.1 · Reviewed 2026-11-19 · Pea Protein Peptides

On this page
  1. Two products, side by side
  2. What hydrolysis does to the protein
  3. Solubility, clarity and viscosity
  4. Bitterness, colour and the flavour system
  5. Protein, peptide and the number on the label
  6. The label and the specification
  7. Choosing between them

Both products start from yellow pea. The isolate is intact protein, separated to a floor of 80% on a dry basis and spray-dried; the peptide is that protein cut by enzymes into shorter chains, specified at ≥80% protein and ≥70% peptide. The differences that decide the application are solubility, viscosity, taste, ash, the analytical method and the name on the label — not the protein number alone.

In one line

Hydrolysis keeps the pea and changes the molecule: the peptide powder dissolves further, tastes more bitter and carries a different name and specification from the isolate.

Two products, side by side

Pea protein peptides and pea protein isolate compared
PointPea protein peptidesPea protein isolate
Protein≥80.0% by Kjeldahl≥80.0% on a dry basis, N × 6.25
Peptide content≥70.0% by HPLCNot a specification line; the protein is largely intact
ProcessExtraction, hydrolysis, inactivation, clarification, dryingAlkaline extraction, isoelectric precipitation, wash, drying
Ash and moistureAsh ≤5.0%; moisture ≤7.0%Ash ≤5.0%; moisture ≤8.0%
SolubilitySoluble; clear to slightly turbid solutionDispersible; opaque, no clear solution
Taste and colourMore bitter and beany; off-white to light tanMilder; light yellow to cream
Viscosity at high solidsUsually lower at the same protein solidsHigher; thickens and can gel
Ingredient nameHydrolysed pea protein or pea protein peptidesPea protein isolate

The table is the short version. The rest of this page takes the four differences that change a formula, and then the two that change the label and the choice.

What hydrolysis does to the protein

An isolate is made by dissolving pea protein at alkaline pH, precipitating it near its isoelectric point, washing and drying. A peptide adds a hydrolysis step: an enzyme, a controlled pH and temperature, a hold time, then inactivation and clarification before drying. The enzyme and the hold time set the degree of hydrolysis, and that sets the average chain length and the share of the powder below the peptide cut-off.

Hydrolysis also changes what the powder carries. pH adjustment leaves salts, so ash is a process line rather than an impurity. A concentrate base brings fibre and starch into the reactor, and they survive into the powder. The grades page keeps peptide content, degree of hydrolysis and base protein as separate levers, because a higher peptide number can come from a longer hydrolysis or from a wider cut-off, and the two are not the same powder.

Solubility, clarity and viscosity

This is the difference most formulas are built on. The isolate disperses in water but does not dissolve to a clear solution; it is opaque, and near its isoelectric point, around pH 4.5, it is least soluble and most likely to sediment. The peptide usually dissolves across a wider pH range, including near that point, and gives a clear to slightly turbid solution at the catalog specification. For a clear or lightly coloured drink, that is the property that decides the ingredient.

The same change usually lowers viscosity at a given protein solids, because shorter chains interact less and do not build the network that gels an isolate. A stick pack or a high-protein drink can therefore carry more protein solids before it turns thick. The trade is osmolality: hydrolysis raises the number of particles in solution, and a concentrated peptide drink can be more osmotic than the same protein weight as isolate. That is a formulation measurement, not a label claim.

Bitterness, colour and the flavour system

Hydrolysis exposes hydrophobic residues that were buried in the intact protein, and those peptides taste bitter. Pea also carries green and beany notes from its own lipids and volatiles. The isolate is milder, which is why it is the easier starting point for a neutral-tasting bar or a plain shake; the peptide is the harder one, and the flavour system has to carry it.

Three levers move the taste: the base protein, the enzyme and the degree of hydrolysis, and the flavour system. A well-washed isolate base gives a lighter colour; a concentrate base or a high ash gives a deeper, more savoury powder. Colour runs from off-white to light tan in the peptide and from light yellow to cream in the isolate, and both darken with heat and moisture. Qualification at the intended dose, in the intended matrix, is the only reliable test of whether the bitterness is acceptable.

Protein, peptide and the number on the label

The two products are not dosed on the same arithmetic. For the isolate, the label figure is protein, and at 80.0% on a dry basis and 8.0% moisture the as-is protein is 73.6%; 25 g delivers 18.4 g of protein. For the peptide, the catalog protein is ≥80.0% by Kjeldahl without a stated basis; if that is as-is, 25 g delivers 20.0 g of protein, and at the 70.0% peptide floor 17.5 g of that is peptide. If the 80.0% is on a dry basis at 7.0% moisture, the same 25 g delivers 18.6 g of protein.

The peptide figure is not added to the protein figure. It is a fraction of the same powder, and a label that declares both as if they were separate contributions overstates the serving. The arithmetic and the basis belong in the specification, and the COA page shows how the certificate reports them.

The label and the specification

The ingredient name changes with the process. The isolate is declared as pea protein isolate; the hydrolysate is declared as hydrolysed pea protein, pea protein hydrolysate or pea protein peptides, depending on the market's naming rules and the buyer's regulatory review. The two names are not interchangeable on a label, even though both start from the same pea.

The source declaration is the same on both sides, because hydrolysis changes the molecular size, not the botanical source. Whether a hydrolysate is less allergenic than the intact protein is a separate question that only an allergenic risk assessment can answer; it is not settled by the peptide percentage. The compliance page sets out the documents and the claim rules.

Choosing between them

Choose the isolate when the formula needs gelation, a mild taste, a white powder or a protein-fortified bar, and when the label should carry the isolate name. Choose the peptide when solubility at high solids or near the isoelectric point matters, when a clear or lightly turbid drink is the target, or when a stick pack needs to carry more protein without thickening. The peptide's bitterness and ash are the constraints to check first.

Neither is a drop-in for the other: the protein basis, the ash, the taste, the viscosity and the label name all move. Keep the specification on the same side as the label, and confirm the destination route before the first order. The product page carries the peptide limits; the pea protein isolate page carries the intact-protein limits; the soy protein isolate page is the counterpart if the source is still open; the methods library covers the tests, and the quality page the release file.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation