02 Grade comparison

Pea peptide grades: peptide content, hydrolysis and form

Technical document 02 · Reviewed 2026-11-19 · Pea Protein Peptides

On this page
  1. Why one name covers more than one powder
  2. The levers that define a grade
  3. What the powder is like to handle
  4. The arithmetic at the dose
  5. Lines the specification must fix
  6. When a peptide is the wrong grade

Pea protein peptides are sold on three things that the word “peptide” does not fix: how much of the powder is peptide, how far the protein was hydrolysed, and which pea protein went into the reactor. The catalog grade is a powder at ≥80% protein and ≥70% peptide; granulation is a format change, while a different peptide floor or a different base protein is a separate specification.

In one line

The grade of a pea peptide is set by the peptide content, the degree of hydrolysis and the base protein behind it, not by the protein percentage alone.

Why one name covers more than one powder

Hydrolysis is a process, not a fixed product. A protease cuts the pea protein at its own preferred sites, and the enzyme, the pH, the temperature and the time decide how short the chains become. Two suppliers can both sell “pea peptides” and deliver powders that differ in peptide content, average chain length, ash, colour and bitterness. The name describes the route; the specification has to describe the powder.

The base protein adds a second variable. An isolate base starts near 80% protein on a dry basis with little fibre and starch; a concentrate base carries more of both into the reactor, and that shows up in the colour, the carbohydrate by difference and the flavour. Neither is wrong, but they are not interchangeable in a formula, and the certificate should name which one was used.

The levers that define a grade

Pea peptide grade levers and what each one changes
LeverCatalog positionWhat it changes
Peptide content≥70.0% by HPLCThe share of the powder in peptide form; the rest is intact protein, free amino acids, ash and moisture
Degree of hydrolysisCan be agreed; report the method and the valueAverage chain length, solubility, bitterness and osmolality
Base proteinNamed in the specificationFibre, starch, colour and flavour carried into the hydrolysate
Ash≤5.0%Salts from neutralisation and minerals from the pea; affects taste and the label
Moisture≤7.0%Flow, caking and the as-is protein figure
Particle size≥95% through 80 meshDust, wetting and the fill on a capsule line

Note the two numbers that are often confused. Peptide content is a mass fraction: 70% of the powder is peptide. Degree of hydrolysis is the share of peptide bonds that were cut, usually measured by OPA or TNBS. A powder can have a high peptide content and a modest degree of hydrolysis if the starting protein was already partly broken, or a lower peptide content and a high degree of hydrolysis if much of the nitrogen ended up as free amino acids. Ask for both, and for the method behind each.

What the powder is like to handle

The catalog form is an off-white to light tan powder at 80 mesh, soluble in water to a clear to slightly turbid solution. That solubility is the main physical difference from the isolate, which disperses but stays opaque. The peptide powder is hygroscopic; an open pouch in a humid filling room takes up water, cakes and loses flow. Plan the weigh-up and the hold time around a sealed container, not around a scoop left on the bench.

Taste moves with the grade. Short hydrophobic peptides are bitter, and pea brings its own green and beany notes; a higher degree of hydrolysis usually means more bitterness alongside the better solubility. Colour is lighter in a well-washed isolate-based hydrolysate and deeper when a concentrate base or a higher ash is carried through. Neither property is captured by the certificate, which is why a sample at the intended dose belongs in the qualification.

The arithmetic at the dose

Dose arithmetic starts from the as-is protein figure, not the peptide figure. At 80.0% protein as-is, 25 g of powder delivers 20.0 g of protein, of which at least 17.5 g is peptide at the 70.0% floor. If the 80.0% is on a dry basis at 7.0% moisture, the same 25 g delivers 18.6 g of protein and 17.5 g at the peptide floor. The difference between those two answers is the basis, not the powder.

The peptide number is not a substitute for the protein number on a label. A nutrition panel declares protein, and a claim is calculated from the protein figure; the peptide content describes the ingredient's composition. Keep the two lines separate in the specification and in the label review, and let the peptide against isolate comparison carry the cross-product arithmetic.

Lines the specification must fix

  1. The material and the route: pea protein peptides, an enzymatic hydrolysate of pea protein, with the base protein named.
  2. Protein, with the factor and basis: ≥80.0% by Kjeldahl, N × 6.25, as-is or dry basis stated.
  3. Peptide content, with the method and the cut-off: ≥70.0% by HPLC distribution.
  4. The degree of hydrolysis, if the formula depends on solubility or taste, with the method named.
  5. Ash ≤5.0%, moisture ≤7.0% and ≥95% through 80 mesh, each with its method.
  6. Heavy metals and microbiology as listed, and the allergen and cross-contact statement for pea and any shared line.

Granulation is written as a format, not a grade: it changes the particle size, the flow and the dust, and it is quoted as a separate line. A diluted powder is a different specification again, because the carrier changes the protein and peptide percentages and the label. The catalog limits are on the product page; the certificate lines are on the COA page.

When a peptide is the wrong grade

Choose the isolate instead when the formula needs gelation, a mild taste or a white powder, or when the label should read “pea protein isolate” rather than a hydrolysate. Choose a concentrate when fibre and starch are wanted and the protein density can be lower. The peptide is the practical choice when solubility at high solids or near the isoelectric point matters, and when the flavour system can carry its bitterness.

The switch is not a drop-in. Protein basis, ash, taste and label name all move, and the pea protein isolate page carries the other side of the comparison, while the soy protein isolate page carries the other legume. The quality page describes how the specification is released against the certificate.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation