06 Identity & adulteration

How we prove a selenium yeast lot is the organic form

Technical document 06 · Reviewed 2026-11-19 · Selenium Yeast

On this page
  1. The four identity layers
  2. Total selenium by ICP-MS
  3. Selenium species, not just selenium
  4. Protein and the selenium-to-protein ratio
  5. Why XRD cannot see a yeast matrix
  6. Adulteration: what to look for
  7. What to write into the specification
  8. Five questions for the supplier

A selenium yeast lot is identified on four levels: it is a yeast, it carries the declared total selenium, that selenium is organic and held in the yeast matrix, and the lot meets the protein and contaminant limits. Total selenium by ICP-MS proves the second level only. The species and the matrix need separate tests, and the specification has to ask for them.

In one line

Total selenium proves the element is there; speciation and the protein-bound fraction prove it is selenium yeast.

The four identity layers

Identity is a stack, not a single assay. A certificate that stops at the first or second layer leaves the most expensive question open.

The four identity layers · selenium yeast
LayerQuestionTestWhat it does not prove
YeastIs the material a yeast?Microscopy, protein, cell-wall markers; species check on requestThat it contains selenium
Total seleniumHow much selenium is present?ICP-MSWhich species, or whether the selenium is organic
SpeciesIs the selenium organic, and which species?HPLC-ICP-MS after extractionThat the species is bound in the yeast matrix
Lot releaseDoes the lot meet the specification?Moisture, mesh, metals, micro, proteinThat the next lot will match

Total selenium by ICP-MS

ICP-MS measures the element after digestion, so the result is total selenium. The method suits a 1,800–2,200 mg/kg specification: it is sensitive, covers the range without dilution trouble, and the contaminant panel can run on the same digest. The certificate should name the isotope, the collision or reaction gas, the internal standard and the limit of quantification.

The result is only as good as the digestion. Yeast protein and cell walls are not always easy to dissolve, and an incomplete digest reads low. A recovery check or certified reference material belongs in the method record, and the number should state its basis.

Selenium species, not just selenium

Speciation separates organic from inorganic selenium. The sample is extracted, usually with an enzyme cocktail, and the extract is run by HPLC coupled to ICP-MS. The common species are selenomethionine, selenocysteine, selenomethylselenocysteine, selenite and selenate. The result is a profile, not a single number.

Two quality checks make the profile readable. Extraction efficiency says how much of the total selenium reached the column; a low figure leaves part unidentified. Mass balance says whether the species results add up to a credible share of the total. A report without either figure is a partial answer.

The EU specification gives the profile a window: selenomethionine at 60–85% of the extracted selenium, other organic compounds at no more than 10%, and inorganic selenium normally no more than 1%. The window is a regulatory definition, not a batch result; the lot's report has to sit inside it.

Protein and the selenium-to-protein ratio

The protein figure is part of the identity. A specification of ≥40.0% describes a yeast matrix with a substantial protein fraction; a powder with the same selenium and much less protein is a different material, or a diluted one. The method is usually Kjeldahl nitrogen × 6.25, and the factor belongs on the certificate.

The selenium-to-protein ratio is a consistency check. At 2,000 mg/kg selenium and 40% protein, the powder carries about 5 mg of selenium per gram of protein. A lot with the same selenium and half the protein is not the same matrix; a lot with the same protein and half the selenium has been diluted, or the fermentation did not load the yeast.

Protein binding is the next question. Selenomethionine can be incorporated into yeast proteins in place of methionine, or remain free in the powder. A speciation run that separates the water-soluble from the protein-bound fraction answers that; a total species figure does not.

Why XRD cannot see a yeast matrix

X-ray diffraction has almost no role in identifying selenium yeast. The material is dried yeast — protein, cell walls and salts, largely amorphous — so a diffractogram is a broad halo, not a phase pattern. Selenium sits at about 2,000 mg/kg, a fraction of a percent, dispersed as organic species; no crystalline selenium phase is expected there. XRD could detect a crystalline inorganic salt added in bulk, but it cannot show that the selenium is organic, which species carries it, or that the matrix is yeast. Those questions belong to ICP-MS, HPLC-ICP-MS speciation and protein. XRD answers a question this material does not pose.

Adulteration: what to look for

Selenium yeast faces five common substitutions, each with a fingerprint usually visible in the file before the drum is opened.

Common substitutions and the tests that show them
SubstitutionWhat it doesFingerprint
Sodium selenite or selenate addedRaises total selenium without fermentationInorganic selenium high; selenomethionine share low; sodium or ash elevated
Low-selenium yeast blended up to a gradeMixes a high-selenium and a low-selenium yeastSelenium and protein ratio shifts; species profile may still look organic
Non-selenised yeast or a non-yeast carrierAdds massSelenium low against protein; microscopy and protein may show a different matrix
Free selenomethionine addedRaises the species figureFree selenomethionine high; protein-bound share low
A different yeast speciesChanges the matrix and the regulatory caseSpecies check; TDS and strain name

The first line matters most for EU-bound lots. Selenite is a permitted source, but it is not selenium-enriched yeast, and adding it changes the ingredient. The EU limit on inorganic selenium, normally 1%, catches it. The second is arithmetic: a 1,000 mg/kg grade can be made by blending a 500 mg/kg base with a 2,000 mg/kg powder. The blend is legitimate only if declared; the species profile alone will not show it.

A sodium result is a useful screen for selenite, because sodium selenite carries sodium. It is not proof; the speciation result is the confirmation. Microscopy and a species check separate a different yeast from the expected one.

What to write into the specification

  • “Selenium-enriched yeast, Se 1,800–2,200 mg/kg by ICP-MS; the yeast species named on the TDS.”
  • “Protein ≥40.0% (nitrogen × 6.25; factor stated); moisture ≤6.0%; ≥95% through 80 mesh.”
  • “Speciation by HPLC-ICP-MS: selenomethionine 60–85% of extracted selenium; other organic ≤10%; inorganic selenium ≤1%; extraction efficiency reported.”
  • “No added sodium selenite, selenate or free selenomethionine; if blended or diluted, every component declared.”
  • “Pb ≤2 · As ≤1 · Cd ≤1 · Hg ≤0.1 mg/kg; APC ≤30,000 cfu/g; yeast and mould ≤100 cfu/g; E. coli and Salmonella absent.”

These lines are limits, not batch results. The certificate repeats them with that lot's figures, and the specification is the reference.

Five questions for the supplier

  1. Which yeast is it, and which selenium source was used in the fermentation?
  2. What is this lot's total selenium, by which method, and on what basis?
  3. Is there a speciation report, with selenomethionine, other organic and inorganic figures?
  4. How was the protein measured, and what conversion factor was used?
  5. Is any selenite, selenate, free selenomethionine or carrier present, and is the lot traceable?

Five direct answers amount to a specification; one selenium percentage does not. The COA page shows where each figure sits; the grade page explains the concentration choice; the compliance page covers the EU species window; the organic versus inorganic page sets out the three sources; the ICP-MS note explains the measurement.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation