02 Grade comparison

1,000 or 2,000 ppm: choosing a selenium yeast grade

Technical document 02 · Reviewed 2026-11-19 · Selenium Yeast

On this page
  1. Why the grade is not the assay
  2. The grades side by side
  3. What changes in the drum
  4. What changes in the finished product
  5. What changes on the label
  6. What to put in the specification

Selenium yeast is sold by total selenium concentration, usually 1,000 or 2,000 mg/kg, on a yeast matrix that also carries protein. The grade changes the mass needed per dose, the fill weight, the blend uniformity and what the label has to say. The higher figure is not automatically the better choice.

In one line

The grade is a concentration on a yeast matrix, so switching it changes the mass, the blend and the label at the same time.

Why the grade is not the assay

Three variables hide behind one grade name: the selenium concentration, the yeast matrix, and the physical presentation. The concentration is a total, not a species assay. A 1,000 mg/kg grade and a 2,000 mg/kg grade can both be selenium yeast, made the same way, with the same organic species profile; the difference is how much selenium the dried powder carries.

That matters because the number on the quotation is not a purity statement. It says how many milligrams of selenium sit in a kilogram of powder, not how much selenomethionine, how much protein, or how much of the selenium is inorganic. Those are separate lines on the specification.

The grades side by side

Selenium yeast grades · powder mass at two daily selenium amounts
GradeSeleniumPowder for 55 µgPowder for 200 µgFitsWatch
1,000 mg/kg0.10%55 mg200 mgLarger capsule, stick, tabletTwice the mass and protein load
2,000 mg/kg0.20%27.5 mg100 mgSmall capsule, tight fillSmall mass; blend uniformity
Diluted gradeBelow 1,000 mg/kg on a carrierDepends on the dilutionDepends on the dilutionDry blends, low-dose productsCarrier must be declared
Granulated 2,000 mg/kg0.20%27.5 mg100 mgTablets, sachetsGranulation aids and flow

What changes in the drum

The yeast matrix is not an inert carrier. It carries protein, cell-wall material and water, and the specification sets protein at ≥40.0% and moisture at ≤6.0%. A 2,000 mg/kg grade delivers the same selenium in half the mass of a 1,000 mg/kg grade, so the protein and the matrix load per dose also halve. That can matter in a capsule with a tight fill weight and in a stick pack where the powder mass is fixed.

Particle size is specified as ≥95% through 80 mesh. Granulation changes flow and density without changing the selenium chemistry; a granulated grade can run on a press that a fine powder would not, and a finer powder can disperse more evenly in a dry blend. The certificate should name the presentation, not only the concentration.

What changes in the finished product

For capsules, the fill weight decides. At 200 µg of selenium, a 2,000 mg/kg grade needs 100 mg of powder; a 1,000 mg/kg grade needs 200 mg. Both can fit a capsule, but the smaller mass leaves more room for other ingredients and the larger mass may rule out a small capsule size. At 55 µg, the masses are 27.5 mg and 55 mg; the 27.5 mg figure is small enough that blend uniformity becomes the real problem, and a dilution or a larger capsule may be the practical answer.

Tablets add flow, density and compression. A granulated grade may help a blend that runs poorly; a finer grade may need a different lubricant or a larger die. Stick packs and drink mixes care about dispersion and taste more than the last decimal of the assay; the yeast matrix has its own flavour, and a higher grade puts less of it in the stick. None of these choices is a health claim; they are formulation consequences.

What changes on the label

The label declares elemental selenium, and the ingredient list names the source. In the EU, the source is written as selenium-enriched yeast; in the US, the Supplement Facts panel can say “Selenium (from selenium yeast)” and the ingredient list names the yeast. A grade change does not change the source name, but it can change the mass of the dosage unit and the % NRV or % Daily Value calculation.

If the grade is a dilution on a carrier, the carrier is a second ingredient and belongs in the list. If the powder is blended with another selenium source, both sources belong in the list. A label that names only the yeast while the drum contains selenite is a labelling defect before it is a quality defect.

The EU reference intake for selenium is 55 µg/day and the US Daily Value is 55 µg/day. A 200 µg dose is well above both, and the EU upper intake level for adults was revised to 255 µg/day in 2023; the US upper level is 400 µg/day. The label arithmetic and the destination ceiling have to be checked before the grade is fixed.

What to put in the specification

  • “Selenium-enriched yeast, Se 1,800–2,200 mg/kg by ICP-MS; nominal 2,000 mg/kg.”
  • “Protein ≥40.0% (nitrogen × 6.25; factor stated); moisture ≤6.0%.”
  • “Particle size ≥95% through 80 mesh; granulated on request.”
  • “Speciation: selenomethionine share and inorganic selenium cap stated in the specification.”
  • “If diluted, name the carrier and its share; if blended, name every selenium source.”

A line that reads only “selenium yeast 2,000 ppm” leaves the species, the matrix and the presentation open. The grade table is useful only if the certificate repeats the same definitions; otherwise the buyer is comparing a name, not a material.

The parameters behind these figures are on the COA page. The species question is on the identity page; the source comparison is on the organic versus inorganic page; the regulatory limits are on the compliance page; the full specification is on the selenium yeast hub.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation