01 COA & batch testing

What a manganese gluconate certificate has to show

Technical document 01 · Reviewed 2026-11-19 · Manganese Gluconate

On this page
  1. The certificate as a test report
  2. One titration, two figures
  3. Release limit versus batch result
  4. What moves between lots
  5. When an outside test is worth ordering
  6. Comparing two suppliers

A manganese gluconate certificate carries two numbers that matter more than the rest: the elemental manganese result and the salt assay calculated from it. Around them sit appearance, infrared identity, water, the contaminant panel, microbiology and particle size. The limits discussed here are catalog limits; the certificate for a lot carries the measured values.

In one line

The certificate has to show the manganese figure and the salt assay from the same titration, with water beside them, because the label dose and the fill weight are calculated from the element.

The certificate as a test report

A laboratory report is auditable when every row names the parameter, the method, the limit and the result. A sheet whose result column repeats the limit is a specification with a letterhead. The table below sets out the lines the catalog requires and the method behind each one.

Identity, assay, water and condition · manganese gluconate
ParameterMethodRelease limit
AppearanceVisualWhite to pinkish powder
IdentificationInfrared spectrum and complexometric titrationConforms to the reference
AssayComplexometric titration98.0–102.0%
Manganese (Mn)Complexometric titration11.5–12.5%
WaterKarl Fischer≤1.0%
Heavy metalsICP-MSPb ≤3, As ≤2, Cd ≤1, Hg ≤0.1 (mg/kg)
MicrobiologyPlate count and absence testsAPC ≤1,000 cfu/g; yeast/mould ≤100 cfu/g; E. coli and Salmonella absent
Particle sizeSieve analysis≥95% through 40 mesh

A reader should be able to tell three questions apart. Identification asks whether the material is manganese gluconate. The manganese line asks how much of the element is present. The assay asks how much salt that element represents. Appearance and mesh describe the powder; contaminants and micro describe the rest of the drum.

One titration, two figures

The titration is an elemental measurement. EDTA complexes manganese in a one-to-one ratio, so the volume of titrant reports manganese, and the laboratory multiplies by a formula factor to obtain the salt. For C12H22MnO14, the molar mass is about 445.2 g/mol and manganese accounts for 54.94, or 12.34%. Dividing 445.2 by 54.94 gives 8.10, the factor that turns a manganese percentage into a salt percentage.

Audit the pair with that factor. 12.2% manganese calculates to about 98.8% salt, a consistent pair. A sheet that prints 11.8% manganese next to 101.0% assay cannot be right both ways: 11.8% corresponds to about 95.6% salt. Each figure may be inside its own catalog range and the two still not belong to one powder, so the sheet should say which was measured and which was derived.

The water result decides the basis. With a ceiling of 1.0% by Karl Fischer, as-is and dried values differ only slightly, but slightly is not the same as not at all. The assay row should state whether the water correction was applied; the water row should carry a measured percentage.

Release limit versus batch result

The limit is the release gate; the result is the evidence. Keep them in separate columns and put the method between them.

Reading a result column against its limit
ParameterRelease limitResult column
Assay98.0–102.0%The measured percentage, the basis and the method
Manganese11.5–12.5%The measured element percentage from the same titration
Water≤1.0%The measured percentage by Karl Fischer
IdentificationInfrared and titration conformThe reference or spectrum file named
Heavy metalsPb ≤3, As ≤2, Cd ≤1, Hg ≤0.1 mg/kgA result for each element, in mg/kg
Particle size≥95% through 40 meshThe measured percentage passing the sieve

Water and manganese are the two lines where a number matters more than a tick. At 0.9% water the lot is inside the limit but close to the ceiling, and a humid store will push it. Because the assay is calculated from the manganese with the 8.10 factor, the two catalog ranges only overlap between about 12.1% and 12.5% manganese; at 12.1% the same dose needs about 3% more powder than at 12.5%. Neither result is a defect, but both change the weigh-up, and a buyer who reads only one limit will miss them.

What moves between lots

Manganese and assay rise and fall together, since one is derived from the other. Reaction, crystallisation and drying move both. Water follows the drying endpoint and the pack. The sieve result follows the mill, and a site change can move it without touching the chemistry.

Colour tells a limited story. The normal range is white to pinkish, and the pink is the manganese. Grey or brown, or dark particles, suggests oxidation or foreign matter and should send the reader to the batch record. Bulk density and flow are not catalog lines, yet they determine whether a capsule line runs or bridges.

Trace the lot code from the certificate to the pouch, the drum and the retained sample, and record the site and the specification revision behind the release.

When an outside test is worth ordering

Outside testing earns its place in four cases: an unfamiliar source, a first entry into a regulated market, a form question the supplier's sheet does not settle, and a disagreement between two laboratories. Keep the panel narrow: a second EDTA titration, an infrared scan against a gluconate standard, Karl Fischer water, ICP-MS for the four metals, and a sulfate limit test if a sulfate blend is suspected.

X-ray diffraction is the addition when a crystalline sulfate phase is the question. A glucose or maltodextrin screen is the addition when dilution is the question. Every screen needs a detection limit; without one, “not detected” describes the method.

Handle the sample as evidence. The laboratory should receive the retained portion, and the report should name the lot, the weight and the basis.

Comparing two suppliers

Two offers are comparable only on the same six lines: the salt and CAS number; the manganese and assay figures with the factor; the water result; the identity methods and the reference; the contaminant and micro results; the mesh and the pack. Agreement on manganese alone proves very little.

Behind the certificate sits traceability: the manufacturer, the manganese source, the drying step, and whether the paper matches the container. A genuine certificate for another lot is still the wrong certificate.

The catalog ranges are on the manganese gluconate product page. The anion and ratio tests are set out on the identity page; the three manganese sources are compared on the grade page; the regulatory file is on the compliance page; release practice is on the quality page. The EDTA method is described in the complexometric method note.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation