06 Identity & adulteration

How a manganese gluconate lot is identified

Technical document 06 · Reviewed 2026-11-19 · Manganese Gluconate

On this page
  1. The identity layers
  2. The manganese-to-salt ratio
  3. X-ray diffraction: the solid-state check
  4. What adulteration looks like
  5. How to write the identity into the specification
  6. Five questions for the supplier

A manganese gluconate lot passes identity when four independent checks line up: the paperwork names the salt and its CAS number, infrared matches a gluconate standard, the titration reports 11.5–12.5% manganese, and the salt calculated from that figure falls in 98.0–102.0%. Manganese alone is not enough, because the sulfate and the oxide also contain it. The anion test and the ratio separate them, and colour is the weakest evidence of all.

In one line

Identity is the manganese figure, the anion and the mass balance agreeing at once: titration says how much manganese, infrared says which salt, and the ratio says whether the two belong together.

The identity layers

A correct name on a certificate is a claim, not evidence. The checks below answer different questions and need separate results; a supplier who answers only the first has described paperwork.

Layers of manganese gluconate identity
CheckWhat it settlesMethodWhat it cannot tell you
PaperworkThe salt and CAS numberName, CAS number, formulaWhether the powder matches
ElementThe manganese contentComplexometric titrationWhich anion carries the metal
AnionGluconate or another acidInfrared against a reference; gluconate identificationThe amount of salt
RatioWhether the two figures agreeManganese against the calculated assayWhich adulterant is present
PhaseA crystalline second saltSulfate limit test; X-ray diffractionThe manganese figure

The manganese-to-salt ratio

The salt holds one manganese atom per gluconate, and the formula fixes the proportion. The theoretical manganese content is 12.34%, and 8.10 is the factor that converts the element into salt. A lot at 12.2% manganese therefore works out at about 98.8% salt, inside the assay range and consistent with the same titration. A certificate showing 11.8% manganese beside a 101.0% assay is not consistent, because the element and the salt cannot both be right.

Two common problems show up in that comparison. A blend with manganese sulfate lifts the manganese above 12.5% and, because the factor assumes gluconate, lifts the calculated salt figure with it, often past 102.0%; the sulfate test and the infrared spectrum are what name the extra anion. A dilution with glucose or maltodextrin pulls both figures down and usually moves the water result. Each line can look plausible on its own; the ratio is what exposes the pair.

Water is the third input. The catalog sets water at no more than 1.0% by Karl Fischer, so as-is and dried results sit close together, but the certificate should still say which basis the assay uses. A dried-basis result and an as-is result are not the same powder, even when the printed percentage is identical.

X-ray diffraction: the solid-state check

Diffraction reads the solid, not the solution. If the lot is crystalline, its pattern can be compared with a reference, and a manganese sulfate monohydrate phase shows reflections of its own; manganese oxide would show a different set again. That makes diffraction a useful second opinion when a blend is suspected, but it is not a purity assay and it says nothing about how much manganese is present.

Ask for the reference pattern and the detection limit behind a “match” statement; without them, the word proves only that a diffractometer was switched on. Reserve the test for a disputed lot or a new source rather than every release.

On a disputed lot, diffraction, infrared and the manganese-to-salt ratio answer three different questions. Together they are stronger than three repetitions of the same assay.

What adulteration looks like

Common manganese gluconate substitutions and the signals
SubstitutionEffectSignalCheck
Manganese sulfateMore manganese; sulfate addedManganese above 12.5%; assay lowSulfate test, XRD, ratio
Manganese oxideDark colour; high manganese; poor solubilityDark specks; insoluble residueXRD, visual, solubility
Glucose or maltodextrinLess manganese and less saltBoth figures low; density or taste shiftInfrared, ratio, water
WaterDilutes the as-is assayWater high; dried assay normalKarl Fischer
IronColour change and a contaminantGrey or brown castICP-MS and the batch record

Colour is the weakest signal. White to pinkish covers a wide range, and a blend can be milled to match it. The sulfate test, the diffraction pattern and the ratio are the stronger evidence. If the certificate reports appearance and manganese but says nothing about the anion, the most likely substitution remains untested.

How to write the identity into the specification

  • “Manganese gluconate, CAS 6485-39-8, C12H22MnO14.”
  • “Complexometric assay 98.0–102.0%, with the basis named on the certificate.”
  • “Manganese 11.5–12.5% on the same lot; water ≤1.0% by Karl Fischer.”
  • “Infrared identity against a named gluconate reference, confirmed by titration.”
  • “Sulfate limit test, with the limit written into the specification.”
  • “At least 95% through 40 mesh; contaminants and microbiology as listed.”

Five questions for the supplier

  1. Which salt is this lot, and which CAS number appears on the certificate?
  2. Can you send the infrared spectrum and the reference, not only the word “conforms”?
  3. What manganese result was measured, what factor converts it to the assay, and is that assay on the as-is or dried basis?
  4. What water result did Karl Fischer return for this lot?
  5. If a sulfate blend is suspected, will you run a sulfate limit test and a diffraction scan on the retained sample?

Five direct answers amount to an identity file; a single manganese percentage does not. The product hub carries the catalog ranges; the COA page explains how each figure is reported; the grade page compares the manganese sources; the level-four comparison takes the sulfate question further; the methods index explains the titration, infrared and diffraction tests; release practice is on the quality page.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation