02 Salt and grade

Manganese gluconate grades: the salt, the powder and the fill

Technical document 02 · Reviewed 2026-11-19 · Manganese Gluconate

On this page
  1. One salt, two decisions
  2. The manganese sources side by side
  3. The powder: mesh, flow and water
  4. Dose arithmetic and the capsule
  5. What to write into the specification
  6. When a grade change is the wrong answer

Manganese gluconate is a single salt, yet two choices sit behind the name: the manganese source on the label and the powder grade on the line. The gluconate reports 11.5–12.5% manganese, the sulfate monohydrate 31.5–33.0% and the bisglycinate 25.0–27.5%, so the source decides how much powder a dose needs. Within the gluconate, the grade decides mesh, flow and water.

In one line

The grade question has two layers: which manganese salt the label names, and which powder the line can fill; the salt sets the manganese figure, and the powder sets the fill.

One salt, two decisions

No granulation changes the manganese percentage. The formula sets it, and a granulated lot and a standard lot from one batch will report the same figure. What the powder grade changes is behaviour: how the material runs through a hopper, how much space it takes in a capsule or sachet, and how much dust it makes at the weigh station.

The source choice comes first and is a different kind of decision. Three manganese salts with three CAS numbers sit in the catalog, and each carries its own label name. An order that says only “manganese” has not chosen among them; the label, the fill and the market file all hang on which salt is meant.

The manganese sources side by side

The table compares the three catalog sources on the lines that change a formula.

Three manganese sources in the catalog
PropertyGluconateSulfate monohydrateBisglycinate
CAS number6485-39-810034-96-514281-77-7
Manganese11.5–12.5%31.5–33.0%25.0–27.5%
Salt per 1 mg manganese (theoretical)About 8.1 mgAbout 3.1 mgAbout 3.8 mg
Water on the certificate≤1.0%, Karl Fischer10.0–12.0%, Karl Fischer≤5.0%, loss on drying
SolutionFreely soluble; neutralFreely soluble; acidicSoluble; acidic
Label nameManganese gluconateManganese sulfateManganese bisglycinate

The comparison is arithmetic, not a ranking. Per milligram of manganese the gluconate needs roughly 2.6 times the mass of the sulfate and 2.1 times the mass of the chelate, because most of the gluconate molecule is the acid rather than the metal. The sulfate is the concentrated salt; the bisglycinate is a chelate with a glycine ratio of its own. Which one belongs in a formula is a label and dosage-form question.

The powder: mesh, flow and water

The catalog gluconate passes 40 mesh at 95% or better. It dissolves freely and leaves a neutral solution, so dissolution is not the issue at this particle size. The issue is water: the powder takes moisture from the air and cakes under load, and a drum that is opened repeatedly has more exposure than a pouch that is used once.

Granulation is a new specification rather than a bigger pack. It changes the sieve line, usually raises density and cuts dust, and may introduce a binder that has to be declared and checked. Capsule lines generally do well with the standard powder; a tablet press is where the granulated option should be trialled.

Density is not a catalog line. Ask for the measured value and the method, because two lots that both pass the sieve can pack differently enough to change a fill.

Dose arithmetic and the capsule

At 2 mg manganese, at the catalog midpoints, the gluconate weighs about 16.7 mg, the sulfate about 6.2 mg and the bisglycinate about 7.6 mg. In a normal capsule that is a small fraction of the fill, so the carrier and the mixing step decide uniformity, not the salt.

Salt mass for a manganese dose, at the catalog midpoints
Elemental manganeseGluconate at 12.0%Sulfate at 32.3%Bisglycinate at 26.3%
2 mgAbout 16.7 mgAbout 6.2 mgAbout 7.6 mg
5 mgAbout 41.7 mgAbout 15.5 mgAbout 19.0 mg
10 mgAbout 83.3 mgAbout 31.0 mgAbout 38.0 mg

Use the table for planning, then reset the target from the lot certificate. The published manganese range spans 8.7 mg of gluconate per milligram at 11.5% to 8.0 mg at 12.5%; the assay gate narrows the usable window, but the lot certificate still sets the fill.

A high-dose product changes the picture. A 500 mg capsule of gluconate holds about 60 mg manganese; the same fill of sulfate holds about 160 mg. A large manganese target therefore favours the sulfate or the chelate, while a small target is easier to blend with the bulkier gluconate.

What to write into the specification

  • “Manganese gluconate, CAS 6485-39-8, formula C12H22MnO14.”
  • “Complexometric assay 98.0–102.0%, with the basis named on the certificate.”
  • “Manganese 11.5–12.5% and water ≤1.0% by Karl Fischer on the same lot.”
  • “Infrared identity against a named reference, confirmed by titration.”
  • “At least 95% through 40 mesh; density reported with its method.”
  • “Any granulation declared, with the processing aid named.”
  • “Contaminants and microbiology as listed in the catalog.”

When a grade change is the wrong answer

Granulation solves flow and dust. It does not turn the gluconate into the sulfate or the chelate, and it does not repair a label that names another salt. A formula that needs the chelate needs the chelate.

Neither does a grade change fix water. The pack and the store do; the stability page describes the behaviour after opening.

The catalog ranges are on the product page. The gluconate against the sulfate is taken further on the level-four comparison; the sulfate has its own product page; the chelate is described on the manganese bisglycinate page; the release tests are on the COA page.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation