What the magnesium sulfate COA must show about the hydrate
A magnesium sulfate certificate has to be read on the heptahydrate basis. The assay of ≥99.0%, the magnesium figure of 9.5–10.0% and the water of 48.0–52.0% are three views of the same molecule, and the identity rows should show the sulfate as well as the magnesium. The limits below are the catalog specification; the batch COA is the document that shows what a particular lot measured.
On a magnesium sulfate certificate the water figure is not an impurity: it is the hydrate, and the magnesium, sulfate and water lines have to agree on the same lot.
The certificate as a test report
For each line the reader needs the parameter, the method and the limit the lot was released against. A row that says only “conforms” reports a conclusion and withholds the evidence. The identity rows deserve particular attention here, because a magnesium titration confirms the metal but says nothing about the anion.
| Parameter | Method | Release limit |
|---|---|---|
| Appearance | Visual | Colourless crystals or white powder |
| Identification | IR and titration; sulfate reaction | Conforms to the reference |
| Assay (heptahydrate basis) | Complexometric titration | ≥99.0% |
| Magnesium | Complexometric titration | 9.5–10.0% |
| Water | Karl Fischer | 48.0–52.0% |
| Heavy metals | ICP-MS | Pb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg |
| Microbiology | Plate count and absence tests | APC ≤1,000 cfu/g; yeast and mould ≤100 cfu/g; E. coli and Salmonella absent |
The sulfate identity is usually shown by the barium chloride reaction: a white precipitate forms in acidified solution and does not dissolve in dilute acid. That line is what separates magnesium sulfate from magnesium chloride, magnesium citrate or magnesium oxide on paper. The assay titration will pass for any soluble magnesium salt, so the anion row is not a formality.
The heptahydrate basis, the water and the magnesium figure
The formula MgSO4·7H2O is 51.2% water by mass. That water is part of the crystal, not a contaminant and not a drying failure. The certificate should therefore say that the assay and the magnesium result are reported on the material as received. A dried-basis magnesium figure of about 20.2% is the anhydrous salt's content, not a richer heptahydrate, and a certificate that mixes the two bases has described two different powders.
The magnesium and water lines move together. A properly sealed heptahydrate near the middle of the water range sits near 9.9% magnesium. A lot that reads 9.7% magnesium with 47.0% water does not fit the heptahydrate formula, and the certificate has to explain the gap. This is why the catalog fixes both a magnesium range and a water range, rather than a single assay number.
Complexometric titration measures the magnesium and calculates the salt from it. It does not measure sulfate, and it does not prove the hydrate. The certificate needs the Karl Fischer result and an anion identity beside the titration, or the assay is only a metal count.
Release limit versus batch result
The release limit is the acceptance boundary. The batch result is what the laboratory measured. Both belong on the page, in separate columns, with the method named. A result column filled with the specification range is a copy of the gate, not a result.
| Parameter | Release limit | What the result column shows |
|---|---|---|
| Assay | ≥99.0% on the heptahydrate basis | A measured percentage and the basis |
| Magnesium | 9.5–10.0% | A measured percentage by titration |
| Water | 48.0–52.0% | A measured percentage by Karl Fischer |
| Sulfate identity | Conforms | The reaction or instrument result, with the reference |
| Heavy metals | Per element | A figure in mg/kg for each element |
| Microbiology | Counts and absence | The count and the absence statement for the lot |
A certificate that reports 9.8% magnesium, 51.0% water and 99.4% assay gives a reader a coherent picture. One that reports only 99.5% assay leaves the hydrate unverified. “Passes specification” is a conclusion the reader should be able to reach from the numbers, not a substitute for them.
What moves between batches
Crystallisation and drying move the water figure and the crystal size. A lot dried hard enough to fall below the 48.0% floor is a lower hydrate, not a more concentrated heptahydrate, and it should be rejected or re-specified rather than accepted as a bonus. Milling moves the particle-size result: the catalog powder is 40 mesh, while crystals are a separate offer. The chemistry can be unchanged while the handling behaviour is not.
Sampling is the quiet source of variation. Magnesium sulfate heptahydrate is efflorescent, so a sample left open in a warm, dry room can lose water before the Karl Fischer test. The certificate may then describe a drier lot than the drum. Ask how the sample was handled and whether the water result came from a sealed subsample.
Chloride, sodium and heavy metals follow the raw material and the process. A sulfate made from a different magnesium source can carry a different chloride profile, and the certificate should show the chloride result where the specification sets one. Colour is a weak indicator: colourless crystals and white powder cover a wide range of particle size and minor variation.
When to order an outside test
Order an independent test for a new source, a first shipment into a regulated market, a disputed hydrate, or a suspicion that the lot is another magnesium salt. The useful panel is magnesium by complexometric titration, sulfate by ion chromatography or gravimetric barium sulfate, water by Karl Fischer, chloride by ion chromatography, sodium by ICP-OES, and XRD for the crystal phase. Add the heavy-metal panel and microbiology for a market release.
The sulfate and magnesium results should be read as a pair. If the magnesium is high and the sulfate is low, the lot may carry magnesium oxide or magnesium chloride. If the sodium is high and the magnesium is low, sodium sulfate is the likely diluent. A “not detected” line needs the method's detection limit to mean anything.
Keep the chain of custody short: the sample tested should be the retained sample, and the report should name the lot. When a result is contested, give the referee the retained sample, the supplier's certificate and the specification, and ask for the tests that separate the salts rather than a repeat of the same titration.
What to compare between suppliers
Put six lines side by side: the hydrate and CAS number; the assay and magnesium result with their basis; the water result; the sulfate identity; the heavy-metal and microbiology results; and the pack with its lot code. Two quotations that agree on assay but differ on water or anion are not describing the same material.
The catalog line is on the magnesium sulfate product page. The identity page sets out the sulfate and water tests, the grade page covers the hydrate choice, the titration method note explains the assay, and the quality page describes the release file.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation