06 Identity & adulteration

How we prove a magnesium sulfate lot is the heptahydrate

Technical document 06 · Reviewed 2026-11-19 · Magnesium Sulfate

On this page
  1. The four identity layers
  2. The 1:1 ratio and the mass balance
  3. X-ray diffraction: the hydrate phase
  4. What substitution looks like
  5. How to write identity into the specification
  6. Five questions for the supplier

A magnesium sulfate lot is the heptahydrate when four lines agree: the document names the hydrate and CAS 10034-99-8, the magnesium titration gives about 9.9%, the sulfate reaction or ion chromatography confirms the anion, and the Karl Fischer water is 48.0–52.0%. The magnesium figure alone cannot separate the sulfate from the chloride, the citrate or the oxide. The anion and the water are what make this salt the one on the specification.

In one line

Magnesium alone cannot prove the salt: the sulfate figure, the 1:1 ratio and the water of crystallisation have to agree on the same lot.

The four identity layers

A certificate can name the right material and still fail to prove it. The four layers below are separate questions, and each needs its own evidence. A supplier who answers only the first has described the paperwork, not the powder.

Four layers of magnesium sulfate heptahydrate identity
LayerQuestionTestWhat it proves
DocumentIs the hydrate named?Name, CAS number, formulaPaperwork only
MagnesiumIs the metal present?Complexometric titrationThe magnesium, not the salt
SulfateIs the anion sulfate?Barium chloride reaction or ion chromatographyThe sulfate
WaterIs it the heptahydrate?Karl Fischer and XRDThe hydrate

The magnesium titration is quantitative and useful, but it is blind to the anion. The sulfate reaction is qualitative and quick: acidify the solution and add barium chloride; a white precipitate that does not dissolve in dilute acid is barium sulfate. Ion chromatography gives the sulfate figure as a number, which is what a ratio check needs. The water result is the hydrate's fingerprint.

The 1:1 ratio and the mass balance

The formula has one magnesium ion for every sulfate ion. On a mass basis that is 9.86% magnesium, 38.97% sulfate and 51.16% water, which sums to 100%. The numbers are fixed by the formula, so a certificate that reports magnesium and sulfate on the same lot can be checked against the ratio rather than read as two unrelated results.

Theoretical composition of magnesium sulfate heptahydrate
ComponentTheoretical shareCatalog lineWhat a deviation suggests
Magnesium9.86%9.5–10.0%A lower hydrate, a blend or a different salt
Sulfate38.97%Identity; assay where agreedA chloride, oxide or sodium-sulfate substitution
Water51.16%48.0–52.0%Efflorescence, over-drying or free moisture

The sulfate-to-magnesium mass ratio is about 3.95. If the magnesium is low and the sulfate is high, sodium sulfate is a likely diluent, because it adds sulfate without magnesium. If the magnesium is high and the sulfate is low, magnesium oxide or magnesium chloride is the more likely contaminant. A blend can hold the magnesium figure inside the range while the anion changes, which is why the anion result belongs on the same lot.

The water closes the balance. A result of 51.0% water with 9.8% magnesium and 39.0% sulfate describes the heptahydrate. A result of 47.0% water with the same magnesium does not, even if the assay still reads above 99.0%.

X-ray diffraction: the hydrate phase

X-ray diffraction answers a different question from titration: is the solid the crystalline heptahydrate, and does its pattern match a reference? It can distinguish the heptahydrate from the hexahydrate, the monohydrate and the anhydrous salt, and it can show a sodium sulfate phase that a magnesium assay would miss. It is not a purity assay and it does not measure the counter-ion.

Ask for the reference pattern and the detection limit before reading a “match” statement. A certificate that says only “XRD conforms” without the pattern or the reference has added little. XRD is most useful when the water result sits at an edge, when a supplier claims a hydrate that the water figure does not support, or when two sources are being compared.

For a disputed lot, XRD plus sulfate plus magnesium plus water is stronger than any one of them. The combination shows the phase, the anion and the metal on the same sample, which is what an identity file is for.

What substitution looks like

Substitutions and deviations in magnesium sulfate
SubstitutionWhat it doesSignalTest
Magnesium chlorideRaises magnesium per gram; adds chlorideChloride high; sulfate low; powder dampChloride by ion chromatography; XRD
Sodium sulfateAdds sulfate without magnesiumSodium high; magnesium lowSodium by ICP-OES; magnesium titration
Magnesium oxideRaises magnesium; lowers sulfateInsoluble residue; sulfate lowAcid solubility; sulfate assay
Magnesium carbonateRaises magnesium; lowers sulfateEffervescence with acidAcid reaction; XRD
Lower hydrateRaises magnesium; lowers waterWater below 48.0%; magnesium highKarl Fischer; XRD

Appearance is the weakest signal. Colourless crystals and white powder cover a wide range, and a different magnesium salt can look the same. The stronger signals are the chloride and sodium figures, the sulfate result, the water and the XRD phase. A certificate that reports appearance and magnesium but not the anion has left the most likely substitution untested.

How to write identity into the specification

  • “Magnesium sulfate heptahydrate, CAS 10034-99-8, MgSO4·7H2O.”
  • “Assay ≥99.0% on the heptahydrate basis; magnesium 9.5–10.0%; water 48.0–52.0% by Karl Fischer.”
  • “Identification by IR and titration; sulfate reaction conforms; sulfate by ion chromatography where a figure is agreed.”
  • “Chloride and sodium limits stated on the certificate where the source or the market requires them.”
  • “XRD reference pattern available where the hydrate phase is disputed.”
  • “No magnesium chloride, sodium sulfate, magnesium oxide or lower hydrate above the stated limit.”
  • “Lot code and retained sample linked to the certificate.”

Five questions for the supplier

  1. Which hydrate is this lot, and which CAS number is on the certificate?
  2. What are the magnesium and sulfate results on the same lot, and by which methods?
  3. What is the water result, and was the sample sealed before the Karl Fischer test?
  4. Is there an XRD pattern, and which reference pattern does it match?
  5. What are the chloride and sodium results, and are they inside the agreed limits?

Five direct answers make an identity file; a single magnesium percentage does not. The product hub carries the catalog specification; the COA page shows where each figure sits on the certificate; the grade page compares the hydrates; the XRD method note explains the phase check; the quality page describes the retained sample.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation