02 Grade comparison

Heptahydrate, monohydrate or anhydrous: choosing a magnesium sulfate grade

Technical document 02 · Reviewed 2026-11-19 · Magnesium Sulfate

On this page
  1. Why magnesium sulfate comes in several grades
  2. The three hydrates side by side
  3. Crystals, powder and the 40 mesh line
  4. The magnesium figure and the fill weight
  5. What to write into the specification
  6. When not to switch grade

The magnesium sulfate grade is the hydrate. The catalog material is the heptahydrate, MgSO4·7H2O, specified at 9.5–10.0% magnesium and 48.0–52.0% water; the monohydrate and the anhydrous salt are different specifications with higher magnesium per gram. Within the heptahydrate, the second choice is crystal or 40 mesh powder. The grade changes the fill weight, the label arithmetic and the pack, not only the assay.

In one line

The grade is the hydrate: heptahydrate, monohydrate and anhydrous magnesium sulfate carry different magnesium per gram and need different specifications.

Why magnesium sulfate comes in several grades

The hydrate state is set by how far the crystallisation and drying steps are taken. The heptahydrate is the standard commercial form and the one described on this site. The monohydrate is an intermediate with less water, and the anhydrous salt is the fully dried form. All three can be ≥99.0% pure and still be different materials, because the water of crystallisation is part of the formula rather than a contaminant.

That is why a magnesium figure without a hydrate name is ambiguous. A certificate showing about 20% magnesium is not a stronger heptahydrate; it is the anhydrous salt's content. A buyer who compares quotations on the magnesium percentage alone can end up comparing three different hydrates, or an anhydrous lot against a heptahydrate specification.

The second axis is particle form. The catalog offers a 40 mesh powder and crystals on request. Crystal size does not change the chemistry, but it changes dust, flow, dissolution rate and how the material behaves in a blend.

The three hydrates side by side

Composition of the magnesium sulfate grades
PropertyHeptahydrateMonohydrateAnhydrous
FormulaMgSO4·7H2OMgSO4·H2OMgSO4
Molecular weight246.47138.38120.37
Magnesium9.86%17.56%20.19%
Water of crystallisation51.2%13.0%None
AppearanceColourless crystals or white powderWhite powderWhite powder
Water solubilityFreely solubleFreely solubleFreely soluble, with heat of hydration
Typical roleStandard supplement gradeHigher magnesium per gramLow-water applications

The table is a composition table, not a ranking. The heptahydrate is not the weakest grade because it carries the most water; it is the grade with the longest commercial record and the one for which the catalog ranges on this page are written. The anhydrous salt is not automatically the better purchase: it is more reactive with moisture and needs a specification written for it.

Crystals, powder and the 40 mesh line

The heptahydrate is available as crystals or as a white powder. Crystals are easier to see and handle, produce less dust and dissolve more slowly; a 40 mesh powder blends more evenly into a stick mix or a capsule fill and dissolves faster. Neither form is more “natural” than the other. The choice belongs to the dosage form and the process, not to the label story.

Particle size also affects caking. A fine powder has more surface area and picks up or loses water at the surface faster than a coarse crystal. The heptahydrate is efflorescent, so a warm, dry store can change the water figure at the surface even while the centre of the particle is unchanged. A granulated or milled version is a separate specification with its own bulk density and flow.

The catalog format is a 40 mesh powder, with crystals on request. If a process needs a different mesh, a granulation or a denser powder, that should be written into the specification before the quotation, because the change moves the particle-size line and may move the lead time.

The magnesium figure and the fill weight

The label declares elemental magnesium; the ingredient list names magnesium sulfate. The bridge between them is the hydrate. At 9.86% magnesium, 100 mg of elemental magnesium needs 1.01 g of the heptahydrate; 200 mg needs 2.03 g; 300 mg needs 3.04 g. The same 100 mg from the anhydrous salt needs about 0.50 g, and from the monohydrate about 0.57 g.

Those differences decide the dosage form. A 700 mg capsule fill of the heptahydrate carries about 69 mg of magnesium; a 1 g stick pack carries about 99 mg; a 2 g stick carries about 197 mg. A formula that needs 200 mg of magnesium per serving cannot fit into a single small capsule of the heptahydrate, and the answer is a larger fill, a second capsule or a different salt — not a magnesium figure borrowed from an anhydrous certificate.

Taste and mouthfeel follow the mass as well. The heptahydrate is bitter and saline, and a 2 g stick is a noticeable amount of powder in a drink. The formulator trials the matrix at the real magnesium dose, not at a rounded spoonful. The label arithmetic, the fill weight and the sensory trial should use the same hydrate number.

What to write into the specification

  • “Magnesium sulfate heptahydrate, CAS 10034-99-8, MgSO4·7H2O.”
  • “Assay ≥99.0% on the heptahydrate basis; magnesium 9.5–10.0%; water 48.0–52.0% by Karl Fischer.”
  • “Identification by IR and titration; sulfate reaction conforms to the reference.”
  • “Appearance colourless crystals or white powder; 40 mesh powder or crystals as agreed.”
  • “Heavy metals and microbiology as listed; chloride limit where the source or the market requires one.”
  • “Hydrate state, particle form, pack and lot code stated on the certificate and the label.”
  • “No substitution of the monohydrate or the anhydrous salt without a written change control.”

When not to switch grade

Do not move to the anhydrous salt only to shrink a capsule. The change alters the water content, the hygroscopicity, the dissolution behaviour and the label arithmetic, and it needs a new specification, a new stability check and a label review. The same applies in reverse: a monohydrate lot is not a heptahydrate with less water, and accepting it against a heptahydrate specification leaves the certificate and the purchase order describing different materials.

The heptahydrate is the right grade when the formula, the label and the pack were built around it, which is the usual case for capsules, sticks and drink mixes. The anhydrous grade is the right choice only when a low-water powder is genuinely needed and the specification, the stability data and the pack are written for it. A technical grade is not a food grade whatever its assay, and it should not enter a supplement file.

The product hub carries the catalog specification. The sulfate versus chloride comparison covers the other salt decision, the COA page shows where the hydrate is declared, and the stability page covers what the water does in storage.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation