01 COA & batch testing

What the COA for anhydrous magnesium sulfate has to show

Technical document 01 · Reviewed 2026-11-20 · Magnesium Sulfate Anhydrous

On this page
  1. The certificate as a test report
  2. The magnesium basis, the drying result and the sulfate
  3. Release limit versus batch result
  4. What moves between batches
  5. When to order an outside test
  6. What to compare between suppliers

The certificate for an anhydrous magnesium sulfate lot reports magnesium by complexometric titration, sulfate by precipitation or ion chromatography, loss on drying, the heavy-metal panel and microbiology. The catalog sets magnesium at 19.0–20.5% and loss on drying at ≤1.0%; the drying result is what keeps the word “anhydrous” honest. A magnesium figure without it cannot separate this salt from a partly hydrated lot.

In one line

On an anhydrous certificate the magnesium figure, the loss on drying and the sulfate identity have to agree, because the water line is what separates this salt from a hydrate.

The certificate as a test report

The certificate is readable only when each row carries the parameter, the method and the limit the lot was released against. “Conforms” is a conclusion, not evidence, and it belongs on the identity row, while microbiology is reported as counts and an absence statement. For magnesium and loss on drying the reader needs a number.

The sulfate row separates magnesium sulfate from the other magnesium salts. A complexometric titration counts magnesium and will pass for the chloride, the citrate or the oxide; the anion test is the part that names this salt. The drying row then decides whether the salt is the anhydrous grade or a lower hydrate.

Identity, magnesium, water and contaminants · magnesium sulfate anhydrous
ParameterMethodRelease limit
AppearanceVisualWhite to off-white powder
IdentificationMagnesium and sulfate testsConforms to the reference
MagnesiumComplexometric titration19.0–20.5%
Loss on dryingGravimetric≤1.0%
Heavy metalsICP-MSPb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg
MicrobiologyPlate count and absence testsAPC ≤1,000 cfu/g; yeast and mould ≤100 cfu/g; E. coli and Salmonella absent
Particle sizeSieve analysis≥95% through 80 mesh

The magnesium basis, the drying result and the sulfate

The magnesium figure is reported on the material as received, not on a dried basis. A powder sold as anhydrous is defined by carrying very little water, so drying it before the assay would hide the result the buyer is paying for. A lot with 4.0% loss on drying and 19.4% magnesium as-is would calculate to 20.2% on a dried basis, the theoretical figure for pure MgSO4; the dried number would look correct while the powder was not anhydrous.

The two lines also check each other. At the theoretical 20.19% magnesium, a result of 19.0% corresponds to about 94.1% MgSO4. If the loss on drying is only 0.6%, the missing 5.3% is not water, so the certificate should account for it through the sulfate balance, sodium or another impurity line. The drying result decides which explanation fits.

The sulfate is usually shown by the barium chloride reaction: a white precipitate forms in acidified solution and does not dissolve in dilute acid. Ion chromatography or gravimetric barium sulfate gives a figure where one is wanted. The reaction identifies the anion; the figure closes the mass balance, and a magnesium percentage alone has identified the metal, not the salt.

Loss on drying is gravimetric under the conditions named on the certificate. It is not the same test as Karl Fischer water, and the two are not interchangeable across methods; the certificate should name the method so results can be compared from lot to lot.

Release limit versus batch result

The release limit is the gate; the batch result is the measurement. Both belong on the page, in separate columns, because a result column filled with the specification range is a copy of the gate rather than evidence.

What the result column should contain
ParameterRelease limitResult column
Magnesium19.0–20.5% as receivedA measured percentage and the titration method
Loss on drying≤1.0%A measured percentage, with the drying condition
Sulfate identityConformsThe reaction or instrument result and the reference
Heavy metalsPer elementA figure in mg/kg for each element
MicrobiologyCounts and absenceThe count and the absence statement for the lot

A result of 19.7% magnesium with 0.4% loss on drying is a coherent anhydrous lot. The same magnesium with 1.4% loss on drying is outside the drying gate even though the magnesium sits inside its range, and it should not be released as anhydrous. The reader should see that from the two lines together, without a footnote.

What moves between batches

The dryer sets the loss on drying. Anhydrous magnesium sulfate is made by driving water out of a hydrate, and the last fraction is the hardest to remove; a shorter residence time leaves more water in the powder. The magnesium figure then drifts down on an as-is basis, so falling magnesium and rising loss on drying are one story, not two.

Particle size and bulk density move with the finishing step. The catalog powder is ≥95% through 80 mesh; a change of mill, sieve or feed rate can shift the distribution while the chemistry is unchanged. Granulation is a separate specification, not a batch-to-batch variation.

Sampling is the quiet source of variation for a hygroscopic salt. A subsample left open on a bench takes water from the air before it is weighed, so the loss on drying reads high and the magnesium reads low. Ask whether the sample was sealed before the test, and whether both results came from the same subsample. Colour is a weak signal: white to off-white covers a wide range.

When to order an outside test

Order an independent test for a new source, a first shipment into a regulated market, a disputed “anhydrous” claim or a suspicion that the lot is a hydrate or another magnesium salt. The useful panel is magnesium by complexometric titration or ICP-OES, sulfate by ion chromatography, loss on drying, chloride and sodium, the heavy-metal panel, microbiology and X-ray diffraction.

XRD answers the hydrate question directly. The anhydrous salt, the monohydrate and the heptahydrate have different patterns, and a scan against a reference can show whether the powder is the phase named on the certificate. Protect the sample from air during preparation and scanning: a hygroscopic powder can pick up water and change phase before the pattern is collected. Ask for the reference pattern and the detection limit.

The sample tested should be the retained sample, and the report should identify the lot. In a dispute, give the referee the retained sample, the certificate and the specification, and ask for the tests that separate the forms, not a repeat of the same titration.

What to compare between suppliers

Put six lines side by side: the form and CAS number; magnesium and loss on drying on the same lot; the sulfate identity and, where available, the sulfate figure; the particle-size result; the heavy-metal and microbiology results; and the pack with its lot code. Two offers that agree on magnesium but differ on drying or anion are not describing the same powder.

The catalog line is on the anhydrous magnesium sulfate product page. The identity page sets out the sulfate, water and phase tests; the grade page covers the particle and hydrate boundaries; the titration method note explains the magnesium assay; the quality page describes the release file.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation