Anhydrous magnesium sulfate: the powder, the mesh and the hydrate line
The catalog grade is the anhydrous powder: MgSO4, CAS 7487-88-9, 19.0–20.5% magnesium, loss on drying ≤1.0% and ≥95% through 80 mesh. Inside that grade the choice is particle form — fine powder or granulated — and each changes flow, dust and dissolution without changing the salt. The heptahydrate is a different product, not a coarser version of this one.
The grade decision is particle form and dryness, not magnesium percentage: a granulated or coarser anhydrous powder still has to meet the same loss on drying.
Why the drying step is the grade
Anhydrous magnesium sulfate is made by removing the water of crystallisation from a hydrate. The last part of that water is the difficult part, and a powder that still carries several percent is a lower hydrate or a partly dried lot, not a more concentrated anhydrous grade. The loss on drying is therefore the line that defines the grade, and the magnesium figure is read beside it rather than instead of it.
The second axis is particle form. The catalog material is an 80 mesh powder; granulation is offered as a separate specification. It changes bulk density, flow, dust and the rate at which the powder dissolves, but it does not change the formula or the magnesium content. A granulated lot that still meets 19.0–20.5% magnesium and ≤1.0% loss on drying is the same salt in a different physical shape.
The third axis is food grade versus technical grade, which is a documentation and contaminant question rather than a chemistry one. A technical grade can share the magnesium range and still fail the heavy-metal, microbiology or documentation lines that a supplement file needs. The grade name has to be read together with the specification and the certificate, not instead of them.
The forms side by side
| Form | Physical state | Magnesium | Water line | Typical use |
|---|---|---|---|---|
| Anhydrous powder, 80 mesh | White to off-white powder | 19.0–20.5% | Loss on drying ≤1.0% | Capsules, dry blends, stick mixes |
| Granulated anhydrous | Agglomerated granules | 19.0–20.5% | Loss on drying ≤1.0% | Dust control and flow |
| Heptahydrate, reference | Crystals or powder | 9.5–10.0% | Water 48.0–52.0% | A different product, not this grade |
The heptahydrate row is in the table to show the size of the boundary, not to offer another grade. Its magnesium content is about half the anhydrous figure because more than half of its mass is water of crystallisation. Comparing the two on magnesium alone makes the hydrate look weaker, when the real difference is the mass per dose and the water specification.
Powder, granule and the handling difference
The 80 mesh powder blends evenly and dissolves quickly, and it also makes dust. In a plant with open weighing, that dust settles on surfaces and takes water from the air; a granulated form reduces the dust and improves flow, at the cost of a slower dissolution step. The choice belongs to the process, not to the label.
Bulk density moves with the form. A granulated material usually packs more mass into the same volume, which can reduce the hopper size or the sachet dimension, but the granule may disperse more slowly than the powder. Granulation changes the particle-size distribution and may add a binder; either way the granule is a separate specification with its own bulk density and flow, and it should not be ordered as “the same powder, coarser”.
The powder is hygroscopic. It does not wait for a humid day to take water: an open container on a bench is enough, and the surface can cake while the centre remains free-flowing. The pack and the handling routine are part of the grade's performance, not an afterthought to it.
The magnesium figure and the fill weight
The label declares elemental magnesium, while the ingredient list names magnesium sulfate. At the theoretical 20.19% magnesium, 100 mg of elemental magnesium needs 495 mg of the anhydrous salt, 200 mg needs 990 mg and 300 mg needs 1,486 mg. A 500 mg capsule of the anhydrous powder carries about 101 mg of magnesium; a 1 g stick carries about 202 mg.
Those numbers decide the dosage form. A 200 mg magnesium formula fits two 500 mg capsules of the anhydrous salt, or one larger tablet, or a 1 g stick. The same 200 mg from the heptahydrate needs about 2.03 g, a different capsule count and a different taste. The label calculation should use the specification midpoint or the measured result, not the highest possible figure.
Dissolution is the other practical difference. The anhydrous salt hydrates as it dissolves and releases heat, so a concentrated stock warms up and a sealed bottle can build pressure. Add the powder to water with stirring and cooling, and do not cap a warm stock. In a dry blend the same reaction can take water from a hygroscopic partner, which is a reason to check the blend's moisture after mixing as well as the raw material's loss on drying.
What to write into the specification
- “Magnesium sulfate anhydrous, CAS 7487-88-9, MgSO4, white to off-white powder.”
- “Magnesium 19.0–20.5% as received, by complexometric titration.”
- “Loss on drying ≤1.0% by the gravimetric method named on the certificate.”
- “Identification: magnesium and sulfate tests conform to the reference.”
- “Particle size ≥95% through 80 mesh; granulated form only when agreed in writing.”
- “Heavy metals and microbiology as listed; 1 kg foil pouch or 25 kg fiber drum.”
- “The word anhydrous on the label is supported by the loss-on-drying result on the lot certificate.”
A specification that names the form and the drying limit, but not the particle form, leaves the physical half of the purchase open. A specification that names the mesh but not the drying limit leaves the anhydrous claim open. Both lines belong in the same document.
When the anhydrous grade is the wrong choice
Choose the heptahydrate when the formula, the label and the market file were built around it, when the larger mass per dose is acceptable and when the pack can keep the crystal inside its water range. The anhydrous salt is not a drop-in replacement: it carries about twice the magnesium per gram, it takes water from the air and it releases heat on dissolution. A switch needs a new specification, a stability check and a label review.
Do not choose the anhydrous grade only to shrink a capsule. The smaller fill is real, but the hygroscopicity, the dissolution heat and the label arithmetic change with it. Do not choose a technical grade for a supplement because the magnesium figure matches; the contaminant and documentation lines are the ones that decide the file. The product hub carries the catalog specification. The anhydrous versus heptahydrate comparison takes the water and label questions further, the heptahydrate page carries the other product, the COA page shows how the drying result is reported, and the methods section covers the assays.
In this document
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation