06 Identity & adulteration

How we prove an anhydrous magnesium sulfate lot is the anhydrous salt

Technical document 06 · Reviewed 2026-11-20 · Magnesium Sulfate Anhydrous

On this page
  1. The identity layers
  2. The magnesium-to-sulfate ratio
  3. X-ray diffraction and the hydrate question
  4. What adulteration looks like
  5. How to write identity into the specification
  6. Five questions for the supplier

An anhydrous magnesium sulfate lot is identified by four agreeing pieces of evidence: the document names the anhydrous salt and CAS 7487-88-9, complexometric titration gives about 20% magnesium, the sulfate reaction or ion chromatography confirms the anion, and loss on drying stays at or below 1.0%. The magnesium figure alone cannot tell this salt from the monohydrate or the heptahydrate. The water line and the anion are what make the identification.

In one line

Identity needs the magnesium, the sulfate and the water to agree: about 20% magnesium with less than 1% water is the anhydrous salt, and a 9.9% magnesium result points to the heptahydrate.

The identity layers

A certificate can carry the correct name and still leave the powder unproven. Each layer below answers a different question, and no layer can borrow evidence from another. A supplier who stops at the document has described the paperwork, not the lot.

Identity layers for anhydrous magnesium sulfate
LayerQuestionTestWhat it proves
DocumentIs the anhydrous form named?Name, CAS number, formula, drying limitPaperwork only
MetalIs the magnesium figure right?Complexometric titration or ICP-OESThe metal, not the salt
AnionIs the counter-ion sulfate?Barium chloride reaction; ion chromatographyThe sulfate salt
WaterIs the hydrate state anhydrous?Loss on drying; Karl Fischer where agreedThe dryness, not the phase
PhaseWhich crystal form is present?X-ray diffractionThe solid form

The water layer is the one that carries the product name. A salt that is 20% magnesium but 8% water is not the anhydrous grade, however the label reads. A salt that is 9.9% magnesium and 51% water is the heptahydrate, whatever the purchase order says. The magnesium and the water have to be read together before the form is named.

The magnesium-to-sulfate ratio

Pure MgSO4 is 20.19% magnesium and 79.81% sulfate by mass. The molar ratio is one magnesium to one sulfate; the mass ratio is 24.305 to 96.06, or about 1 to 3.95. A lot that reports 20.0% magnesium and 79.0% sulfate closes the mass balance, and the small gap is consistent with the measurement uncertainty and the loss on drying.

The ratio is a diagnostic, not a routine release test. If the magnesium is low while the sulfate stays high, a sulfate-bearing diluent such as sodium sulfate is a likely explanation, and the sodium result will show it. If the magnesium is high while the sulfate is low, an oxide, hydroxide or carbonate is more likely, and the sulfate figure and the acid-insoluble residue will move. If both are low, the powder may carry an inert filler or a non-sulfate matrix.

A blend can be built to land inside the magnesium range. Magnesium oxide is about 60% magnesium and sodium sulfate is about 32% sodium, so a formulator can mix them toward 20% magnesium while the sulfate and sodium figures move away from the pure-salt ratio. The titration alone will not see the difference. The anion, the sodium and the mass balance will.

X-ray diffraction and the hydrate question

X-ray diffraction answers the question the chemical tests cannot: which crystal phase is present. The anhydrous salt, the monohydrate and the heptahydrate have different diffraction patterns, and a scan against a reference can show whether the powder is the phase named on the document. This is the direct check on a disputed “anhydrous” claim.

Sample preparation is the weak point. The powder is hygroscopic, so it can take water from the air and change phase between the scoop and the diffractometer. Prepare the sample in a dry box or a sealed holder, and ask how the laboratory protected it. A pattern collected from a damp sample can show a hydrate that was not in the drum.

XRD is not a purity assay, and it does not measure the counter-ion. It complements the magnesium and sulfate results rather than replacing them. Ask for the reference pattern, the scan range and the detection limit before reading a “match” statement, and read a match without the reference as an unverified claim.

What adulteration looks like

Substitutions and blends to check in an anhydrous magnesium sulfate lot
AdulterantWhat changesSignalTest
Heptahydrate or monohydrateWater high; magnesium lowLoss on drying above 1.0%; Mg near 9.9–17.6%Loss on drying, XRD
Sodium sulfateMagnesium low; sodium high; sulfate highNa above the agreed limit; Mg/SO4 ratio offICP-OES sodium, ion chromatography
Magnesium oxide or hydroxideMagnesium high; sulfate low; alkalineHigh Mg with low sulfate; pH riseSulfate by IC, pH, acid-insoluble residue
Magnesium chlorideChloride high; sulfate lowChloride above limit; low sulfateChloride by IC, sulfate by IC
Inert fillerBoth magnesium and sulfate lowResidue high; mass balance shortAcid-insoluble ash, full mass balance

Colour is the weakest signal. White to off-white powders look alike, and a blend can match the appearance of the pure salt without matching its chemistry. The stronger evidence is the anion, the sodium and chloride figures, the water result and the phase. A certificate that reports appearance and magnesium but not sulfate has left the most likely substitution untested.

How to write identity into the specification

  • “Magnesium sulfate anhydrous, CAS 7487-88-9, MgSO4.”
  • “Magnesium 19.0–20.5% as received by complexometric titration.”
  • “Loss on drying ≤1.0% by the gravimetric method named on the certificate.”
  • “Identification by magnesium and sulfate tests; sulfate by ion chromatography where a figure is agreed.”
  • “Sodium and chloride limits where the source, the process or the market requires them.”
  • “XRD reference pattern available where the anhydrous phase is disputed.”
  • “No monohydrate, heptahydrate, sodium sulfate or other magnesium salt above the agreed limit; lot code and retained sample linked to the certificate.”

Five questions for the supplier

  1. Which form is this lot, and which CAS number and drying limit appear on the certificate?
  2. What are the magnesium and loss-on-drying results, and did they come from the same sealed subsample?
  3. What is the sulfate result and method, and does the magnesium-to-sulfate ratio close the mass balance?
  4. What are the sodium and chloride figures, and are they inside the agreed limits?
  5. Is there an XRD pattern, which reference does it match, and how was the sample protected from moisture?

Five answers of this kind form an identity file; one magnesium percentage does not. The catalog entry carries the specification, the COA page shows where each figure sits, the grade page compares the forms, the heptahydrate page marks the boundary, the XRD method note explains the phase check and the quality page the retained sample.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation