06 Identity & adulteration

How we prove a magnesium malate lot is the malate

Technical document 06 · Reviewed 2026-11-18 · Magnesium Malate

On this page
  1. A sequence of four measurements
  2. The 1:1 ratio and the mass balance
  3. Diffraction and the infrared spectrum
  4. The routes worth testing
  5. How to write the specification
  6. Five questions for a supplier

Four measurements carry the identity of a magnesium malate lot: the EDTA magnesium assay, the malate reaction and infrared spectrum, the Karl Fischer water, and an X-ray diffraction pattern. Each one answers a different question, and none of them is sufficient alone. The lot is the malate when the four agree, on the same sample, with a mass balance that closes.

In one line

The magnesium assay proves the metal, not the salt: malate by reaction and infrared, the water by Karl Fischer and the mass balance have to agree on the same lot.

A sequence of four measurements

Identity layers · what each result proves and what it leaves open
LayerMethodQuestion answeredWhat it leaves open
MetalComplexometric EDTA titrationHow much magnesium is presentWhich salt or oxide supplied it
AnionMalate reaction and infrared spectrumWhether malate is presentWhether the malate is associated with the magnesium
WaterKarl Fischer titrationHow much water the powder carriesWhether the water is surface moisture or crystal water
CrystalX-ray diffractionWhich crystalline phases are presentAmorphous content and organic purity

Titration comes first because it is the measurement every certificate carries. EDTA at about pH 10 binds the magnesium ion and reports total metal. That is a quantity, not an identity: magnesium oxide, magnesium carbonate, magnesium citrate and the malate all contribute to the same number.

The anion is the second measurement. A chemical malate reaction is run against a reference, and the infrared spectrum is compared with a reference spectrum. The carboxylate and hydroxyl bands show that malate is present, but a mixture of malic acid and a magnesium salt could still produce a positive reaction. The result has to be read with the assay and the water.

Water is the third measurement. Karl Fischer reports water specifically, and the 22.0–26.5% range is the hydrate's signature as much as the magnesium figure is. A water result outside the range changes the mass balance even when the magnesium stays inside its own range.

The diffraction pattern is the fourth. It identifies crystalline phases, including a crystalline magnesium source that the wet chemistry cannot see. The four results are one identity when they agree; separately they are four data points.

The 1:1 ratio and the mass balance

Magnesium malate has one magnesium ion for each malate ion, because both carry two charges. The catalogue formula, C₄H₁₀MgO₈, has a molar mass of about 210.4 g/mol, and magnesium is about 11.6% of that mass. The rest is malate and water in a fixed proportion. That fixed proportion is the check to run first.

If a certificate reports 11.5% magnesium, the water has to be inside the hydrate range and the malate has to account for the balance. A lot at 11.5% magnesium with 12% water has a mass-balance gap: the missing mass is neither metal nor declared water, and the likely causes are another magnesium salt, a filler or a different hydrate.

The upper limit is a useful ceiling. Magnesium oxide carries about 60.3% magnesium, so a fraction of a percent of oxide moves the assay from the middle of the range to the top. A result above 11.8% cannot be this hydrate, and a result at the top of the range with a low water figure deserves a second look rather than a celebration.

Diffraction and the infrared spectrum

Diffraction is the phase test. A crystalline magnesium oxide fraction has its own pattern, and a report is only useful when it names the detection limit and the sample preparation. The same technique can show a change of hydrate, because the lattice changes when the water content changes.

Infrared spectroscopy reads bonds rather than lattices. The carboxylate region and the hydroxyl band form a pattern to hold against a reference lot. The FTIR and XRD method entries describe what each technique can see.

Neither test measures chemical purity. A phase-pure malate can still carry lead or cadmium, which is why the contaminant panel is run beside the identity work. If the label depends on the DL designation, add optical rotation; the routine panel does not include it.

The routes worth testing

Adulteration routes · magnesium malate
Added materialWhy it appearsWhat movesTest that shows it
Magnesium oxideLifts magnesium at a low additionMagnesium high, water and malate lowMass balance, XRD
Magnesium citrateA similar white magnesium powderCitrate reaction positive, IR differsCitrate test, IR, magnesium figure
Malic acidRaises the malate signal and acidifiespH below 4.0, magnesium lowpH, mass balance, IR
Magnesium carbonateLifts magnesium and adds carbonateEffervescence on acid, magnesium highAcid test, XRD, mass balance
Another hydrateDrying or hydration mismatchWater outside 22.0–26.5%, magnesium shiftedKarl Fischer, XRD, batch record

Oxide is the usual first suspect: a small addition raises the metal quickly, and the mass balance plus diffraction expose it. Citrate brings a different anion and a different infrared spectrum. Malic acid lifts the malate signal while pulling pH and magnesium down. Carbonate raises magnesium and fizzes on acid. The fifth route is paperwork rather than chemistry: a different hydrate supplied against this line.

Read one test at a time and a blend can pass each of them. Read them together, on one lot, and the identity is the agreement between the numbers.

How to write the specification

  • “Magnesium DL-malate dihydrate, CAS 869-06-7.”
  • “Magnesium 11.3–11.8% by complexometric EDTA, as-is basis.”
  • “Water 22.0–26.5% by Karl Fischer on the same lot.”
  • “Malate identity by reaction and infrared spectrum; reference standard named on the certificate.”
  • “pH 4.0–7.0; ≥95% through 80 mesh; bulk density 0.50–0.85 g/mL.”
  • “No added magnesium oxide, magnesium citrate, malic acid or carrier.”
  • “Optical rotation, where the DL designation is a label requirement.”

The negative clauses matter: a range with no added-mineral clause leaves the door open, and an unwritten ban cannot be enforced.

Five questions for a supplier

  1. Which hydrate does the lot represent, and what water result does Karl Fischer give?
  2. Which reference standard was used for the malate reaction and the infrared comparison, and can the spectrum be shared?
  3. Was the magnesium result run on the powder as-is or after drying, and what water figure belongs to the same lot?
  4. Has any magnesium oxide, magnesium citrate, malic acid or carrier been added after the reaction?
  5. What is the XRD detection limit, and is a report available for the lot?

Answers to all five describe a material that can be written into a purchase specification. An answer to the magnesium figure alone describes a number. Where each result sits on the certificate is covered on the COA page; the salt decision is on the grade page; the catalogue line these questions test is on the product hub. The same lot discipline is described on the quality page.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation