01 COA & batch testing

What the COA for magnesium malate actually contains

Technical document 01 · Reviewed 2026-11-18 · Magnesium Malate

On this page
  1. What the sheet carries
  2. What 11.3–11.8% is measured against
  3. Release limit and batch result
  4. What moves between lots
  5. When a second laboratory earns its place
  6. What to compare between suppliers

Every lot of magnesium malate is released against a one-page certificate that reports the EDTA magnesium assay, the malate identification, Karl Fischer water, pH, particle size, bulk density and the contaminant and microbiology panels. The parameter list is fixed by the specification; the figures beside each line belong to the lot. The certificate only means something when the method, the limit and the result are read as one line.

In one line

The magnesium figure is only the first line: the certificate has to name the malate, the water and the hydrate basis before the number means anything.

What the sheet carries

The certificate follows the release specification for magnesium DL-malate dihydrate. Each row names the parameter, the method and the limit the lot has to meet, and the measured result sits beside them on the lot certificate. A result without a method cannot be compared with another laboratory's number.

Release specification · magnesium DL-malate dihydrate, CAS 869-06-7
ParameterMethodRelease limit
AppearanceVisualWhite to off-white powder
Magnesium (Mg)Complexometric EDTA titration11.3–11.8%
IdentificationMalate reaction and infrared spectrumConforms to reference
WaterKarl Fischer titration22.0–26.5%
pH (5% suspension)Potentiometry4.0–7.0
Particle sizeSieve analysis≥95% through 80 mesh
Bulk densityCylinder method, poured or tapped as stated0.50–0.85 g/mL
Heavy metalsICP-MS or ICP-OES, as statedPb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg
MicrobiologyPlate count and enrichmentAPC ≤1,000 cfu/g · yeast and mould ≤100 cfu/g · E. coli and Salmonella absent

The microbiology block reports aerobic plate count, yeast and mould, E. coli and Salmonella. The limits are agreed in the specification before the lot is tested, not selected after the result is known.

What 11.3–11.8% is measured against

The magnesium range describes the powder as it is packed. It is not a purity percentage or a dried-basis result. The catalogue formula, C₄H₁₀MgO₈, has a molar mass of about 210.4 g/mol; magnesium contributes 24.3 g/mol, so the theoretical fraction is about 11.6%. The specification range is drawn around that number, and the water is part of the same formula mass.

That is why 11.5% magnesium is not a low grade. The 98% or 99% figure that appears in quotations usually refers to the salt content, not to the metal. The two numbers answer different questions. A quotation that offers “99% magnesium malate” without an elemental magnesium figure has not told the buyer what the label can declare.

The water figure is 22.0–26.5% by Karl Fischer. It is a range rather than a maximum because the hydrate is the product. A lot at the low end of the water range will read a little higher on magnesium than a lot at the high end, even when both are the same salt. If a certificate reports magnesium on a dried basis, that has to be stated on the same page: the as-is and dried-basis figures are not interchangeable, and the dried figure for this material would sit near 15% rather than near 11.5%.

Release limit and batch result

A release limit is the window the lot must fall inside; the result is the number the bench obtained for that lot. The certificate should show both, with the method beside each. “Passes specification” is a conclusion, not a result; the buyer cannot audit it and cannot compare it with the next lot.

Water is the line that is most often misread. Here it is a two-sided range because the hydrate has to be present. A result below the range is not a cleaner lot; it may be a drier hydrate or a different hydrate, and the magnesium figure will have moved with it. A result above the range points to surface moisture or a drying step that stopped early. Neither is automatically a rejection; both need the batch record.

The method matters as much as the number. EDTA titration measures total magnesium and says nothing about the anion. Karl Fischer measures water specifically; a loss-on-drying result at 105 °C can remove water of crystallisation as well as surface moisture, and the figure depends on the method conditions. A certificate that reports loss on drying instead of Karl Fischer water is not necessarily wrong, but the two results cannot be compared without the method.

What moves between lots

The magnesium assay follows the neutralisation and crystallisation steps. The malate comes from the DL-malic acid used, and a change of acid source is a change of supplier file even when the assay stays inside the range. Water follows the crystallisation and drying steps and is the most variable figure on the sheet. pH follows the residual acid or alkali in the liquor. Particle size and bulk density follow milling and sieving.

Colour is the least quantitative signal and often the first useful one. A cream or grey tint can point to a hot drying step, an iron trace or a shift in the malate source. The assay may still pass. The tint is a cue to check the batch record.

When a second laboratory earns its place

Order an outside test when the material comes from a new source, on the first shipment into a regulated market, when the label's form claim is not proved by the certificate, or when a result is disputed. Do not order a photocopy of the supplier's certificate. Order the few tests that settle the point in doubt: EDTA or ICP for magnesium, the malate reaction plus an infrared spectrum, Karl Fischer water, an XRD check for crystalline magnesium oxide, and ICP-MS for the metals panel on that sample.

An outside laboratory is also the practical way to resolve a disagreement. Send the retained sample, the specification and the supplier's certificate, and ask for the tests that distinguish the salt.

What to compare between suppliers

Line up six facts before comparing quotations: the salt and hydrate, the magnesium figure and its method, the water figure and its method, the malate identity reference, the mesh and bulk density, and the presence or absence of an oxide screen. Two certificates can agree on 11.5% magnesium and disagree on the other five, and then they are not describing the same material.

The second layer is traceability. The certificate lot, the drum lot and the retained-sample lot should match. An accurate certificate can still belong to a drum that never reaches you.

The catalogue line behind this page is on the magnesium malate product page. The salt choice is set out on the grade comparison page, the tests that separate the malate from a blend are on the identity page, and the assay itself is described in the EDTA titration method entry. The release workflow sits on the quality page.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation