Ferrous sulfate heptahydrate vs dried: the iron figure and the fill weight
The heptahydrate is 20.09% iron and 45.36% water by formula; the dried grade is about 30–33% iron and 10–13% water. The same 20 mg iron dose needs about 100 mg of heptahydrate or about 63–67 mg of dried ferrous sulfate, so the dried grade puts more iron into a smaller fill. The choice is a fill-weight and label decision, not only a chemical one.
The same iron dose needs about 100 mg of heptahydrate or about 65 mg of dried ferrous sulfate, and the difference is water the capsule has to carry.
What “dried” actually means
Both articles are ferrous sulfate; they differ in how much water is bound in the crystal. The heptahydrate is FeSO4·7H2O, the pale blue-green crystal that forms from water. The dried grade is made by removing part of that water, usually to the monohydrate or a mixture of hydrates. It is not the anhydrous salt. The dried article has its own CAS number, 13463-43-9, and the monohydrate has 17375-41-6; the heptahydrate is 7782-63-0.
The dried grade exists because water is dead weight in a dry dosage form. A kilogram of heptahydrate carries about 201 g of iron; a kilogram of dried grade at 31% carries about 310 g. The difference shows up in the capsule size, the tablet weight, the number of sacks handled and the space the material occupies.
“Dried” is a commercial article name, not a stoichiometric formula. Two suppliers can both sell “dried ferrous sulfate” at slightly different iron and water figures. The specification has to state the iron window and the water window, not only the word dried.
The iron figure and the mass per dose
| Property | Heptahydrate | Dried grade |
|---|---|---|
| Formula | FeSO4·7H2O | FeSO4·H2O, nominal |
| CAS number | 7782-63-0 | 13463-43-9 |
| Molecular weight | 278.01 | 169.92 as monohydrate |
| Iron content | 20.09% by formula; catalog 19.5–20.5% | About 30–33%; commonly 30.0–32.0% |
| Water content | 45.36% by formula; catalog 45.0–48.0% | About 10–13% |
| Iron per 100 mg | About 20.1 mg | About 30–33 mg |
| Mass for 20 mg iron | About 99.6 mg | About 62.5–66.7 mg |
| Appearance | Pale blue-green crystals or powder | Gray-white to off-white powder |
| Solubility in water | About 26 g per 100 mL at 20 °C | Soluble; dissolves more slowly |
The arithmetic scales with the dose. At 40 mg of iron the heptahydrate needs about 199 mg and the dried grade about 125–133 mg. These are formula figures, not batch results; the certificate's iron result replaces the theoretical 20.09% or 31% in the calculation.
The water difference is the other half of the table. A 20 mg iron dose from the heptahydrate brings about 45 mg of water into the capsule; the dried grade brings about 7–10 mg. At 40 mg of iron the gap is about 90 mg against about 13–17 mg, which is enough to change the tablet weight and the water activity of a blend.
Fill weight, capsule size and the blend
For a capsule, the fill-weight difference is small at 20 mg of iron and decisive at higher doses or in a small shell. A 60 mg iron dose is about 299 mg as heptahydrate but about 188–200 mg as dried grade, so the same dose can move from a smaller shell to a larger one or force a change in the excipient load. A powder blend follows the same arithmetic in percentage terms, and the dried grade leaves more room for a second active.
For a tablet, the water in the heptahydrate moves into the granulation. It can help a wet granulation and hurt a dry one, and it can react with alkaline excipients such as calcium carbonate or sodium bicarbonate. The dried grade carries less water, but it is still hygroscopic and still acidic; it is not a neutral filler.
In a powder blend, the iron density changes the share of the formula. A 20 mg iron dose is about 10% of a 1 g stick pack when supplied as the heptahydrate and about 6.5% as the dried grade. That changes the flow, the segregation risk and the taste of the blend, and it changes the amount of carrier the formulator needs.
Solution behaviour
Both grades dissolve in water and give a pale green, acidic solution at pH 3.0–4.0. The heptahydrate dissolves at about 26 g per 100 mL at 20 °C; the dried grade dissolves more slowly and may need more agitation or a longer hold. In a solution the water content of the solid no longer matters, because the water is already there. What matters is the iron concentration, the pH and the oxygen load.
A liquid formula built on “grams of salt per litre” changes its iron concentration when the grade changes. A 10 g/L solution of heptahydrate carries about 2.01 g/L of iron; the same 10 g/L of dried grade at 31% carries about 3.1 g/L. The formula has to be written on iron, not on salt weight, and the batch record has to show which grade was weighed.
The heptahydrate is the conventional solution grade. The dried grade can be used, but the dissolution time and any residue should be checked in the actual process.
What the label has to say
The label names the source and declares the element. In the EU the ingredient list should name “ferrous sulfate heptahydrate” or the dried article, and the nutrition declaration gives iron in mg and as a percentage of the 14 mg/day reference intake. In the US the Supplement Facts panel gives elemental iron in mg and its percentage of the 18 mg Daily Value, with the source in the ingredient list.
“Ferrous sulfate” alone is ambiguous on a label. The hydrate is part of the ingredient identity, and a switch from one grade to the other without a label change would name the wrong material. The dose declaration also has to match the weigh-up: a label that declares 20 mg of iron assumes about 100 mg of heptahydrate or about 65 mg of dried grade.
When to choose which
Choose the heptahydrate for a solution, a syrup, a crystal grade or a process built around a soluble ferrous salt. It is the form that dissolves readily. Choose the dried grade for a capsule, a tablet or a dry blend where the fill weight is tight, the iron dose is high, or the water from the heptahydrate would migrate into a moisture-sensitive matrix.
Do not use the two as interchangeable. A label that names the heptahydrate needs the heptahydrate, and a formula written for 31% iron will under-deliver by about a third if the heptahydrate is weighed. The opposite substitution brings a different problem: a dried grade in a solution process may dissolve more slowly and leave a residue the process was not designed to handle.
Catalog data are on the ferrous sulfate hub; the grades page sets this choice beside the other forms; the ferrous fumarate and ferrous gluconate pages cover the alternative salts; the complexometric method note explains the iron assay and the quality page the release process.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation