06 Identity & adulteration

How we prove a ferrous sulfate lot is the heptahydrate

Technical document 06 · Reviewed 2026-11-19 · Ferrous Sulfate

On this page
  1. The five identity layers
  2. The iron-to-water ratio: fixing the hydrate
  3. X-ray diffraction and the solid state
  4. What adulteration looks like
  5. Writing identity into the specification
  6. Five questions for the supplier

A ferrous sulfate lot is the heptahydrate when the document names the hydrate and CAS 7782-63-0, the ferrous and sulfate reactions both match, the iron is 19.5–20.5%, the water is 45.0–48.0%, and the two figures agree with the FeSO4·7H2O formula. The iron assay alone cannot separate the heptahydrate from the dried grade, the anhydrous salt or a partly oxidised lot. The water figure and the ferric check are the measurements that close that gap.

In one line

The hydrate is the identity: the ferrous and sulfate reactions name the salt, the iron and water figures fix the heptahydrate, and the ferric check shows how much has oxidised.

The five identity layers

A certificate can carry the right name and still leave the powder unproven. Each level below answers a different question and carries a different proof. A supplier who stops at the first has supplied a label, not a material.

Five layers of ferrous sulfate heptahydrate identity
LevelWhat it answersMethodEvidence supplied
DocumentIs the hydrate named?Name, CAS number, formulaA statement on paper
Ferrous reactionIs the iron ferrous?Potassium ferricyanide or phenanthrolineFe2+, not the counter-ion
Sulfate reactionIs the counter-ion sulfate?Barium chloride; white precipitateSulfate, not the metal
Iron and waterDoes the ratio fit the heptahydrate?Complexometric iron and Karl Fischer waterHydrate stoichiometry
Solid formIs the crystal the expected one?X-ray diffraction or infrared spectrumCrystal form, not purity

The order matters. The reactions identify the salt; the numbers identify the hydrate; the solid-state method identifies the crystal. None of them replaces the others, and the certificate should show enough of each to let a reader repeat the conclusion.

The iron-to-water ratio: fixing the hydrate

The formula fixes the arithmetic. Iron is 55.85 ÷ 278.01 = 20.09% of FeSO4·7H2O; water is 126.11 ÷ 278.01 = 45.36%; sulfate is 34.55%. The molar ratio is one iron to one sulfate to seven water. The catalog windows — iron 19.5–20.5% and water 45.0–48.0% — are wide enough to allow a little surface moisture, but not wide enough to turn the heptahydrate into the dried grade.

The ratio is a diagnostic. If a lot reads 19.8% iron, the expected crystal water is about 44.7%; a measured 47.0% means roughly 2.3% extra water, and the iron is diluted in proportion. If a lot reads 31% iron and 10% water, it is the dried article, not a wet heptahydrate. The two figures together are far more specific than either one alone.

The ferric check adds the oxidation state. Total iron by ICP-OES minus ferrous iron by redox titration gives ferric iron. For illustration, a lot with 20.2% total iron and 19.6% ferrous iron carries 0.6% ferric iron, about 3% of its total iron. That is the figure that tells a buyer whether the pale blue-green colour is still describing the material.

Sulfate by gravimetric barium sulfate or ion chromatography confirms the counter-ion. The theoretical figure is 34.55%; a low sulfate result with a normal iron result points to another anion, and a high sulfate result with low iron points to a sulfate diluent. pH of a 50 mg/mL solution, 3.0–4.0, is a supporting check, not a quantitative one.

X-ray diffraction and the solid state

X-ray diffraction reads the crystal lattice. It can distinguish the heptahydrate from the monohydrate and the anhydrous salt, and a crystalline ferric phase, for example goethite or a basic ferric sulfate, will appear if it is above the detection limit. Amorphous ferric hydroxide has no lattice, so diffraction cannot see it. XRD therefore sits alongside the iron and water results rather than replacing them.

Infrared spectroscopy is the other solid-state check. The spectrum shows the sulfate and water bands and gives a fingerprint that can be compared with a reference of the same hydrate. The catalog identification is infrared plus titration; the spectrum answers “is this the expected solid?”, while the titration answers “how much?”. Neither one alone proves the hydrate.

Before accepting a “match” statement, ask for the reference pattern or spectrum and the detection limit. A match with no reference named proves nothing about the sample.

What adulteration looks like

Likely substitutions in a ferrous sulfate lot
SubstituteEffect on the lotWarning signCheck
Dried or monohydrate gradeLess water, more iron per gramWater below 45%; iron above 20.5%Karl Fischer plus iron
Added waterDilutes the iron; cakingWater above 48%; iron lowKarl Fischer plus iron
Ferric oxidationFerrous iron becomes ferricYellow-brown colour; ferrous figure lowRedox titration plus ICP-OES
Sulfate diluentLowers iron; raises sulfateIron low; sulfate high; foreign cationIon chromatography or ICP-OES
DyeMatches colour, not the chemistryColour without the iron or water ratioFull identity panel

Colour is the weakest signal. The blue-green to brown window is broad enough that a dye can imitate part of it. The stronger signals are the water figure, the iron-to-water ratio and the ferric difference. A sheet that gives appearance and assay but omits water leaves the most probable substitution unexamined.

Writing identity into the specification

  • “Ferrous sulfate heptahydrate, CAS 7782-63-0, FeSO4·7H2O.”
  • “Assay 99.0–101.0% by complexometric titration; iron 19.5–20.5%.”
  • “Water 45.0–48.0% by Karl Fischer titration.”
  • “Identification by infrared spectrum and titration, against a named reference.”
  • “Ferrous reaction and sulfate reaction both conform.”
  • “Sulfate about 34.6% by gravimetry or ion chromatography, where the counter-ion is to be confirmed.”
  • “Ferric iron limit to be agreed; report total iron and ferrous iron on the same basis.”

Five questions for the supplier

  1. What hydrate does the certificate name, and what CAS number is printed beside it?
  2. What are the iron and water results, and which methods produced them?
  3. What is the ferric iron figure, measured as total iron minus ferrous iron?
  4. Will you send the infrared spectrum and the sulfate result, not just the assay number?
  5. If the lot is disputed, is a joint re-test on the retained sample acceptable, with XRD if the crystal form is questioned?

If all five answers arrive with documents, the identity file is complete; one assay figure is not a substitute. Catalog data sit on the ferrous sulfate hub; the COA page maps each figure to its certificate line; the grades page sets the hydrate against the dried grade; the level-four page follows the fill-weight consequences; the XRD note explains the solid-state check and the quality page the release workflow.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation