02 Grade comparison

Ferrous sulfate grades: heptahydrate, dried and the physical form

Technical document 02 · Reviewed 2026-11-19 · Ferrous Sulfate

On this page
  1. Why the same salt comes in three grades
  2. The three chemical grades side by side
  3. Crystals, powder and what the line can run
  4. Fill weight and the iron declaration
  5. What to write into the specification
  6. Where the other grade fails

Ferrous sulfate is bought as the heptahydrate, at 20.09% iron and 45.36% water by formula, or as a dried grade at roughly 30–33% iron and about 10% water. The choice changes the mass per dose, the water load in the blend and the name on the label before it changes anything else. Crystal and powder are physical grades of the same hydrate: the mesh and the flow decide which one a capsule line can run.

In one line

The grade is a water decision before it is an iron decision: the heptahydrate carries about 45% water and 20% iron, the dried grade about 10% water and 31% iron, and the fill weight follows.

Why the same salt comes in three grades

All three grades are ferrous sulfate; they differ in how much water is bound to the crystal. The heptahydrate is FeSO4·7H2O, the form that crystallises from water and the form most solution processes start with. The dried grade is a commercial article made by removing part of that water, usually to the monohydrate or a mixture of hydrates. The anhydrous salt has no crystal water at all and is the most hygroscopic of the three.

The grade is not a purity label. A 99.0% heptahydrate and a 99.0% dried grade are both high-purity articles, but one kilogram of each delivers about 201 g and about 310 g of iron.

“Dried” is the word that causes most of the confusion. It does not mean anhydrous, and it does not mean the heptahydrate with a lower water result. It is a separate article with its own CAS number, its own iron window and its own water window. A buyer who orders “ferrous sulfate” without the grade has left the most important line of the specification open.

The three chemical grades side by side

Ferrous sulfate heptahydrate, dried and anhydrous compared
PropertyHeptahydrateDried gradeAnhydrous
FormulaFeSO4·7H2OFeSO4·H2O, nominalFeSO4
CAS number7782-63-013463-43-97720-78-7
Iron content20.09% by formula; catalog 19.5–20.5%About 30–33%; commonly 30.0–32.0%36.76% by formula
Water content45.36% by formula; catalog 45.0–48.0%About 10–13%None bound; picks up moisture readily
AppearancePale blue-green crystals or powderGray-white to off-white powderOff-white to gray powder
Solubility in waterAbout 26 g per 100 mL at 20 °CSoluble; dissolves more slowlySoluble, with hydrolysis and heat
Typical useSolutions, syrups, crystal gradesDry capsules, tablets, blendsSpecialty dry systems

The dried article may be supplied as the monohydrate, CAS 17375-41-6, or as a partly dehydrated solid under the dried CAS number. The supplier should state which one is on the certificate, because the iron and water figures are the only way to tell them apart in routine testing.

Crystals, powder and what the line can run

The heptahydrate is pale blue-green and crystalline. The catalog powder is specified at 40 mesh; crystals are available on request. A crystal dissolves slowly but cleanly, which suits a solution process that has time and agitation. A powder disperses faster and blends more evenly into a dry mix, but it also generates dust and can cake when the water activity of the room is high.

The heptahydrate is efflorescent: in dry air it gives up crystal water, and the surface of a crystal can turn dull or powdery. In moist air the ferrous iron oxidises and the colour moves towards yellow-brown. Both changes are visible, and neither is a grade change. The dried grade is less water-laden but still hygroscopic; it cakes less than the heptahydrate in a dry blend, and it still needs a sealed pack.

Bulk density and flow differ between a crystal and a milled powder, and they differ between suppliers. If the capsule or tablet line has a fixed volume, ask for the bulk density and the particle-size distribution rather than the mesh figure alone.

Fill weight and the iron declaration

The arithmetic starts with the iron figure, not the salt weight. At 20.09% iron, 20 mg of elemental iron is 20 ÷ 0.2009 = 99.6 mg of heptahydrate. At 31% iron, the same 20 mg is 64.5 mg of dried grade, and at 36.76% it is 54.4 mg of anhydrous salt. At 40 mg of iron the masses become about 199 mg, about 129 mg and about 109 mg. These are arithmetic examples, not a dose recommendation.

The water that comes with the heptahydrate is the difference the formulator feels. A 20 mg iron dose from the heptahydrate carries about 45 mg of water into the capsule; the dried grade carries about 7–8 mg. In a tablet, that water can migrate into the granulation and change the compact; in a capsule, it can soften the shell or react with a moisture-sensitive active. In a dry blend, it changes the water activity of the whole mix.

The label declares elemental iron, while the purchase order is written in salt. The two have to be connected by the iron figure on the certificate, not by the word “ferrous sulfate”. A formula that assumes 20% iron for a dried grade will weigh about 55% more powder than needed; one that assumes 31% for a heptahydrate will under-deliver iron by about a third.

What to write into the specification

  • “Ferrous sulfate heptahydrate, CAS 7782-63-0, FeSO4·7H2O.”
  • “Assay 99.0–101.0% by complexometric titration; iron 19.5–20.5%.”
  • “Water 45.0–48.0% by Karl Fischer titration.”
  • “Identification by infrared spectrum and titration; report the reference.”
  • “Particle size ≥95% through 40 mesh for the powder; crystals on request.”
  • “Heavy metals and microbiology as listed; ferric iron limit to be agreed.”
  • “Grade, CAS number and hydrate named on the COA and the label.”

For a dried grade the same list applies with the dried CAS number, iron 30.0–33.0% and water about 10–13%. Do not write “ferrous sulfate” as the article name on a specification; it describes a family, not a purchase.

Where the other grade fails

If the formula is a dry capsule or tablet with a tight fill weight, the heptahydrate's water is dead weight; the dried grade puts more iron in the same volume. If the formula is a solution, the heptahydrate is the easier starting material and the dried grade offers no advantage. A label that names the heptahydrate rules out the dried grade as a silent substitution: the ingredient declared and the powder weighed would not be the same article.

The reverse also holds. A buyer who needs the heptahydrate for a solution should not take the dried grade as “the same salt, less water” and rebalance later. The hydrate is part of the identity, and the iron figure is the evidence.

Catalog data for the grade sit on the ferrous sulfate hub. The heptahydrate-against-dried page works through the iron and fill-weight sums; the ferrous fumarate and ferrous gluconate pages set out the alternative salts; the methods library covers the assays and the quality page the release sequence.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation