01 COA & batch testing

What the COA for ferrous sulfate heptahydrate actually contains

Technical document 01 · Reviewed 2026-11-19 · Ferrous Sulfate

On this page
  1. Reading the certificate line by line
  2. The hydrate basis, and why water is not a contaminant
  3. Release limit versus batch result
  4. What moves between batches
  5. When an outside test is worth ordering
  6. What to compare between suppliers

The certificate for a ferrous sulfate heptahydrate lot reports appearance, identification, assay by titration, elemental iron, water by Karl Fischer, the heavy-metal panel and microbiology, with the hydrate and the CAS number in the header. Those figures are only comparable when the water result sits beside them: the heptahydrate is 20.09% iron and 45.36% water by formula, so a lot that has lost or gained water reads differently on every line. The values below are the catalog specification; the batch COA confirms one pouch or drum.

In one line

The iron figure only means something beside the water figure: the heptahydrate is 20.09% iron and 45.36% water by formula, and both move when a lot dries or oxidises.

Reading the certificate line by line

A certificate earns trust when another laboratory could repeat every line. The header names the hydrate, the CAS number, the lot and the pack. Each row then gives the test, the method, the release limit and the result.

“Conforms” can be a real result for an identity test, provided the reference is named. Assay and iron are numbers, and both belong on the same basis. The water line makes the other two readable.

Identity, assay, iron and water · ferrous sulfate heptahydrate
ParameterMethodRelease limit
AppearanceVisualPale blue-green crystals or powder
IdentificationInfrared spectrum and titrationConforms to reference
Assay (as heptahydrate)Complexometric titration99.0–101.0%
Iron (Fe)Complexometric titration19.5–20.5%
WaterKarl Fischer titration45.0–48.0%
Heavy metals (Pb, As, Cd, Hg)ICP-MSPb ≤3, As ≤2, Cd ≤1, Hg ≤0.1 mg/kg
MicrobiologyAPC and pathogen screenAerobic count ≤1,000 cfu/g; yeasts and moulds ≤100 cfu/g; E. coli absent; Salmonella absent

The hydrate basis, and why water is not a contaminant

Ferrous sulfate heptahydrate is FeSO4·7H2O at 278.01 g/mol. Iron is 55.85 ÷ 278.01 = 20.09% of the formula, and water is 126.11 ÷ 278.01 = 45.36%. The 45.0–48.0% water window and the 19.5–20.5% iron window describe the same crystal from two directions. The upper water figure allows a little surface moisture; the lower figure catches a lot that has dried out in storage.

The assay is expressed on the hydrate as sold, not on a dried basis. If a laboratory reports iron on a dried basis, the conversion is 20.09 ÷ (1 − 0.4536) = 36.76%, which is the iron content of the anhydrous salt. That figure belongs to a different article. A dried ferrous sulfate at about 31% iron is not this material with less water on the certificate; it is a separate specification with its own CAS number and fill weight.

Karl Fischer measures total water: crystal water plus surface water. A reading of 44.0% falls below the window and points to efflorescence. A result of 49.0% sits above it and points to moisture pick-up. Neither is a purity failure on its own, but both change the iron delivered per gram of powder. The capsule is filled on the powder weight and the label is written on the iron weight, so the two have to be reconciled before the batch record is signed.

Release limit versus batch result

The limit is the boundary for release; the result is the number the laboratory obtained. Both belong on the page, with the method beside them.

What the result column should contain · ferrous sulfate heptahydrate
ParameterRelease limitResult column
Assay99.0–101.0%A measured percentage, with the titration method
Iron19.5–20.5%A measured percentage and the basis
Water45.0–48.0%A measured percentage by Karl Fischer
IdentificationConforms to referenceThe reference named, plus the spectrum
ContaminantsPer elementA measured mg/kg figure for every element named

Each contaminant line needs a detection limit. A reported “Pb <3 mg/kg” means the method stopped at 3; a figure such as 0.4 mg/kg means the element was actually measured. The catalog ceilings for lead, cadmium and mercury match the EU limits for supplements, so a finished product has no room for a second source of those metals. Arsenic is a customer limit because the EU has no general maximum for it in supplements.

The ferric figure is usually missing. The complexometric assay measures total iron after sample preparation; it does not separate Fe2+ from Fe3+. Request a redox titration for ferrous iron alongside a total-iron result, then compare the two. A lot can pass the iron window while part of the iron has already oxidised.

What moves between batches

Water moves first. Drying removes surface water and can begin to remove crystal water; a dry store can effloresce the crystals; a humid store adds water back. Iron on an as-is basis moves with the water, so two powders with the same dried-basis assay can deliver different amounts from the same scoop.

Colour moves from pale blue-green towards yellow-brown as ferrous iron oxidises to ferric. The shift can begin at the surface of a crystal or in a damp layer inside a drum, and the assay can still pass while the appearance has changed. A colour shift should send you to the batch record for the ferric figure; it is not a reason to reject on sight.

A batch at the top of the iron window and the top of the water window is an edge combination, and the two lines should be read together.

When an outside test is worth ordering

An outside laboratory is worth ordering for a new source, a first regulated shipment, a label that names the heptahydrate, or a result the supplier disputes. The useful panel closes the gaps the routine sheet leaves: ferrous iron by redox titration, total iron by ICP-OES, water by Karl Fischer, sulfate by gravimetric barium sulfate or ion chromatography, ICP-MS for the metal panel, and microbiology.

Add X-ray diffraction when the hydrate or the crystal form is in question. The laboratory should report a detection limit and a basis for each line; the sample submitted should be the retained one, accompanied by the supplier's certificate and the agreed specification.

What to compare between suppliers

Six certificate lines to compare across suppliers
LineWhat to askWhy it matters
Hydrate and CASHeptahydrate named, CAS 7782-63-0 on the sheetThe hydrate controls the iron and water arithmetic
IronThe measured figure, its basis and the methodAs-is and dried-basis numbers do not mean the same thing
WaterThe measured percentage and the methodFixes the hydrate and flags caking risk
Ferric (Fe3+)The gap between total and ferrous ironThe routine assay may not see oxidation
SulfateA result by gravimetry or ion chromatographyShows the counter-ion, not only the metal
TraceabilityA lot code linking certificate, pack and retained sampleA correct certificate can still describe a different drum

Read across the six lines, not just the two iron figures. The catalog data are on the ferrous sulfate product page; the tests that distinguish heptahydrate from dried grade are described on the identity page; the release sequence is set out on the quality page; the titration method appears in the complexometric method note and the diffraction check in the XRD note.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation