06 Identity & adulteration

How we prove a ferrous gluconate lot is the ferrous salt

Technical document 06 · Reviewed 2026-11-18 · Ferrous Gluconate

On this page
  1. Four layers, four different failures
  2. Ferrous iron is a number; ferric iron is a difference
  3. What the infrared and X-ray methods add
  4. The routes that change one number at a time
  5. How to write the identity specification
  6. Five questions for the supplier

A ferrous gluconate lot has to be proved on four levels: the declared name and hydrate, the ferrous reaction and infrared spectrum, the cerimetric iron assay on the dried basis, and the contaminant and physical limits. The assay is the only one of the four that puts a number on the ferrous state, and it is blind to everything else. Identity is the four levels together, not the iron percentage alone.

In one line

The ferrous state is the identity: a total-iron figure, an infrared spectrum and a ferric check together prove the salt.

Four layers, four different failures

What each identity layer proves and what it cannot
LayerTestWhat it provesWhat it misses
DocumentName, hydrate, CAS, formulaThe file is about the right moleculeNothing about the powder
Chemical identityFerrous reaction and infrared spectrumThe ferrous ion and the gluconate ligandNot a quantity
AssayCerimetric Fe(II), dried basisFerrous iron contentBlind to Fe(III), water and other salts
ConditionLoss on drying, pH, mesh, metals, microFitness for the specificationNo proof of identity

Each layer catches a different failure. The document catches a wrong name or a missing hydrate; the chemical identity catches a different salt or a different oxidation state; the assay catches a weak or diluted lot; the condition tests catch a lot that is the right molecule but not the right material to ship. A certificate with ticks in all four columns is auditable. One with an iron figure and nothing else is a single number doing four jobs.

The ferrous reaction is the old, simple one: an aqueous solution of the salt gives a dark blue precipitate with potassium ferricyanide. It is sensitive to the ferrous ion and it is not specific to gluconate, which is why the infrared spectrum sits beside it. The infrared comparison identifies the gluconate ligand; the reaction identifies the oxidation state.

Ferrous iron is a number; ferric iron is a difference

Cerimetric titration is a redox method. Cerium(IV) oxidises iron(II) to iron(III), one electron at a time, and the end point is read with an indicator such as orthophenanthroline. Iron(III) in the sample is already oxidised and consumes no titrant, so the result is ferrous iron only. Expressed as iron, each millilitre of 0.1 N ceric sulfate corresponds to 5.585 mg Fe; expressed as the dihydrate, 48.22 mg. Ask which convention the certificate uses.

Total iron needs a different method: ICP-OES or atomic absorption, both of which see every iron atom regardless of oxidation state. Run the two on the same sample, on the same basis, and subtract: ferric iron equals total iron minus ferrous iron. If total iron reads 12.4% and ferrous iron 11.9%, the difference is 0.5% ferric as Fe, about 4% of the iron. Both figures are percentages of iron, not of a ferric compound.

The catalog specification does not set a separate ferric limit. The ferrous assay is the control, and the ferric figure is a supplementary test that the buyer and supplier should agree for the grade. That is a gap worth closing: a lot can sit inside the 11.8–12.5% window with a measurable ferric fraction, and the window alone does not say whether the fraction is acceptable. Colour supports the number — a yellow-brown cast is a prompt, not a result.

What the infrared and X-ray methods add

The infrared spectrum is a fingerprint of the gluconate ligand. Carboxylate absorption sits near 1600 and 1400 cm⁻¹, the broad hydroxyl band near 3400 cm⁻¹, and the whole spectrum is compared with a reference rather than interpreted band by band. IR answers “is this the gluconate salt?” It does not answer “how much iron?” and it is not a purity assay.

X-ray diffraction reads the crystal lattice. It distinguishes the dihydrate from the anhydrous salt and from other crystalline phases, and it can show a crystalline ferric phase such as goethite if one is present above the detection limit. It will not see amorphous ferric hydroxide, which has no lattice to diffract. That is why XRD belongs beside the cerimetric and total-iron results rather than in place of them.

Ask the laboratory for the reference spectrum or the reference pattern, the detection limit and the sample preparation. A “conforms” with no reference named is a comparison with something unnamed. The FTIR method note and the XRD note explain what each technique can support.

The routes that change one number at a time

Adulteration routes for ferrous gluconate and the tests that show them
RouteWhat movesTest that shows it
Oxidised or ferric gluconateFerrous falls, total stays, colour darkensCerimetry against total iron
Another ferrous saltIron may rise; sulfate or ash movesInfrared, sulfate and ash
Iron oxide or ferric powderTotal iron rises, ferrous does notXRD plus the ferric difference
Dextrose or maltodextrin diluentIron falls, moisture and IR changeAssay, IR and loss on drying
Excess waterAs-is iron falls, dried basis holdsLoss on drying beside the assay

The routes share a signature: one number moves while another stays. That is why the numbers have to be read in pairs. A high total with a normal ferrous figure points to an added ferric or elemental source; a low ferrous with a normal total points to oxidation; a low iron with a high loss on drying points to water or a diluent.

A declared blend is not adulteration. If the powder contains ferrous gluconate and another iron source, the label has to name both, and the certificate has to report the contribution. The defect is the undeclared blend, not the blend itself.

How to write the identity specification

  • “Ferrous gluconate dihydrate, C₁₂H₂₂FeO₁₄·2H₂O, CAS 299-29-6.”
  • “Identification: ferrous reaction and infrared spectrum against a named reference.”
  • “Iron(II) 11.8–12.5% on the dried basis by cerimetric titration; loss on drying ≤8.0%.”
  • “Total iron by ICP-OES reported; ferric iron calculated as the difference.”
  • “pH (5% solution) 3.0–5.0; ≥95% through 80 mesh.”
  • “No added ferric salt, iron oxide or diluent; heavy metals and microbiology as the catalog.”

A specification written this way tells the laboratory what to measure and tells the supplier what will be rejected. “Assay 12%” on its own does none of that.

Five questions for the supplier

  1. Is the iron result ferrous iron by cerimetry, and on which basis is it reported?
  2. What is total iron by ICP-OES for this lot, and what is the ferric difference?
  3. Which hydrate and CAS are declared, and does the IR spectrum match a named reference?
  4. What are the loss on drying, pH and particle-size results for this lot?
  5. Who manufactured the lot, and can the batch record and retained sample be tied to the lot code?

Five answers amount to an identity file. A single iron percentage does not. The COA page shows where each figure sits on the certificate, the grade page places the salt among the alternatives, and the product page carries the catalog specification.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation