What the COA for ferrous gluconate actually contains
The certificate for a ferrous gluconate lot reports appearance, iron by cerimetric titration on the dried basis, the loss on drying that the basis depends on, pH, particle size, the heavy-metal panel and microbiology. Each row should show the test, the method and the limit the lot was released against. The ranges here are the catalog specification; the batch COA is the document that confirms a particular pouch or drum.
A ferrous gluconate certificate is only auditable when the iron figure, its drying basis and the moisture result sit on the same page.
The certificate as a test report
A certificate is auditable when every line can be repeated. That needs three things per row: what was measured, which method produced the number, and which limit the lot was released against. The header should name the hydrate, the lot code, the standard and the pack size.
| Parameter | Method | Release limit |
|---|---|---|
| Appearance | Visual | Greyish-yellow to greenish-yellow powder |
| Identification | Ferrous reaction and infrared spectrum | Conforms to reference |
| Iron (Fe), dried basis | Cerimetric titration | 11.8–12.5% |
| Loss on drying | Gravimetric | ≤8.0% |
| pH (5% solution) | Potentiometry | 3.0–5.0 |
| Particle size | Sieve analysis | ≥95% through 80 mesh |
A certificate that reports iron but not moisture has left the basis undefined; one that reports contaminants without detection limits cannot be compared with another laboratory's result.
| Parameter | Method | Release limit |
|---|---|---|
| Heavy metals | ICP-MS | Pb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg |
| Microbiology | Plate count and absence tests | APC ≤1,000 cfu/g · yeast and mould ≤100 cfu/g · E. coli and Salmonella absent |
Appearance is the only line a reader can check without an instrument, and the first that moves when a lot oxidises; it belongs on the sheet even though it is not a number.
What the dried basis is doing
The iron line says “dried basis”, and that phrase is arithmetic. Ferrous gluconate dihydrate is C₁₂H₂₂FeO₁₄·2H₂O at 482.17 g/mol; iron is 11.58% of the dihydrate as sold. Drive off the two water molecules — 7.47% of the mass — and the same iron is 12.52% of what remains. The 11.8–12.5% window and the ≤8.0% loss-on-drying limit describe the same solid from two directions.
The conversion is one line: iron on the dried basis equals iron as-is divided by one minus the loss on drying. If a powder reads 11.4% as-is with 7.0% loss, the dried figure is 12.3%; at 2.0% loss the same arithmetic gives 11.6% and fails. Neither is a batch result — both show why the basis must be printed.
Comparisons fail here more often than anywhere else on the sheet. An as-is result of 11.3% against a dried-basis limit of 11.8% looks like a failure and may be a pass; a dried result of 12.4% against an as-is expectation may be the same powder.
Loss on drying is not a purity figure. Crystal water and surface water are both water, and the 8.0% limit allows for the hydrate plus handling moisture.
Release limit versus batch result
The release limit is the gate; the batch result is the measurement. Both belong in the row, with the method beside them. A result column filled with the specification range is a copy of the gate, not a result.
Identity lines are the exception: the ferrous reaction and the infrared spectrum are comparisons, so “conforms” is a legitimate result if the certificate names the reference and edition. A conformity without a reference is a stamp, not a test.
Contaminant lines need detection limits. “Pb: <3 mg/kg” says the method could not see below 3; “Pb: 0.4 mg/kg” says the lot was measured. The catalog limits sit at the European food-supplement maximum levels for lead, cadmium and mercury, leaving no headroom for a second contributor.
The ferric figure is the line the certificate usually does not carry. Cerimetry counts ferrous iron only, so a lot that starts near the top of the window can oxidise and stay inside it while the declared ferrous salt is no longer fully there. Ask for total iron by ICP-OES beside the cerimetric result and read the difference, as the identity page sets out.
What moves between batches
Iron moves with the reaction, the crystallisation and the drying step. Over-drying removes water and lifts the dried-basis figure; under-drying leaves water and lowers the as-is figure. On a dried basis, the loss-on-drying line explains a drift in the assay.
pH follows washing and residual gluconic acid. The acid end of 3.0–5.0 is normal; a shift towards 5.0 can mean less acid in the liquor or partial hydrolysis, and it changes behaviour beside alkaline excipients.
Colour is the least quantitative line and often the earliest. Greyish-yellow to greenish-yellow is the catalog description; a yellow-brown or reddish cast points to ferric iron. The assay can still pass. Colour is a prompt to pull the batch record, not a rejection on its own.
Mesh moves with milling and sieving. A lot at the coarse end of “≥95% through 80 mesh” flows differently in a capsule machine from one that is almost all through, and the certificate's single percentage hides that spread.
When to send a lot to a second laboratory
Order an independent test for a new source, a first shipment into a regulated market, a label that names the ferrous salt, or a disputed result. The useful panel closes the gaps the certificate leaves.
For this salt the gap is the oxidation state. Ask for cerimetric ferrous iron and total iron by ICP-OES on the same sample, both on the same basis; the difference is ferric iron. Add infrared identity against a reference, X-ray diffraction if the crystalline form is in question, and an ICP-MS panel for lead, arsenic, cadmium and mercury.
Ask the laboratory to state its detection limit and basis for every line, and send the retained sample, the supplier's certificate and your specification together. A referee result without the sample's lot code proves nothing about the drum in your warehouse.
What to compare between suppliers
| Line | What to ask | Why it matters |
|---|---|---|
| Form and hydrate | Dihydrate named, CAS on the sheet | The hydrate sets the iron arithmetic |
| Iron | Result, basis and method | As-is and dried-basis figures are not comparable |
| Loss on drying | Result and conditions | Defines the basis and predicts caking |
| Ferric iron | Total iron minus ferrous iron | The cerimetric assay sees only Fe(II) |
| Particle size | Mesh and percentage passing | Fill weight, flow and dust |
| Traceability | Lot code on certificate, pack and retained sample | An accurate certificate can cover another drum |
Compare the six lines, not the two iron figures. A result on an unnamed basis and a result on a dried basis are not the same statement. The catalog specification sits on the product page; the grade comparison covers the salt choice; the quality page shows the release file; and the ICP-MS note explains the total-iron figure behind the ferric check.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation