Copper bisglycinate vs copper gluconate: the chelate, the copper and the fill
Copper bisglycinate and copper gluconate are both copper(II) sources, but the chelate carries about 30% elemental copper against about 14% for the gluconate. The same label claim therefore needs roughly half the powder, while the gluconate is the form that dissolves freely and the chelate is handled as a dry solid. The choice turns on the matrix, the fill and the ingredient line.
The chelate carries about 30% copper and the gluconate about 14%, so the same claim needs roughly half the powder; the gluconate is the form that dissolves freely.
A chelate and a salt
Copper bisglycinate is a coordination compound: one copper ion is bound by two glycine ligands, each using its amino nitrogen and a carboxylate oxygen, so two five-membered rings close around the metal. The anhydrous formula is C4H8CuN2O4, molar mass about 211.66 g/mol, CAS 13479-54-4. Copper gluconate is an ionic salt: one copper ion and two gluconate anions, C12H22CuO14, molar mass about 453.84 g/mol, CAS 527-09-3.
Both are copper(II) materials with an assay specified at 98.0–102.0%, and both are blue solids. The word chelate describes the ring structure; it is not a grade, a purity level or a claim about what the body does with the copper. The gluconate does not become a chelate by granulation.
| Property | Copper bisglycinate | Copper gluconate |
|---|---|---|
| CAS number | 13479-54-4 | 527-09-3 |
| Formula | C4H8CuN2O4 | C12H22CuO14 |
| Molar mass | About 211.66 g/mol | About 453.84 g/mol |
| Copper, calculated | 30.0% | 14.0% |
| Catalog copper range | 29.0–31.0% | 13.5–14.5% |
| Appearance | Blue powder | Blue-green powder |
| Water solubility | Slightly soluble; acidic solution | Freely soluble; blue-green solution |
| Label ingredient | Copper bisglycinate | Copper gluconate |
The copper figure, not the salt weight
The label declares elemental copper, so the number that matters is copper per gram of powder. At 30.0%, 100 mg of the chelate carries 30.0 mg of copper; at 14.0%, 100 mg of the gluconate carries 14.0 mg. Across the catalog ranges the chelate delivers 29.0–31.0 mg and the gluconate 13.5–14.5 mg per 100 mg. The chelate is about 2.1 times more concentrated in the metal.
That ratio cuts both ways. A formula that swaps the gluconate for the chelate at equal powder weight delivers more than twice the copper and overclaims the label; the reverse swap underclaims it. The correct conversion is by copper, not by salt, and it changes the weigh-up before anything else.
Neither figure is a purity statement. Both materials can meet a 98.0–102.0% assay while carrying their own copper content; the certificate needs both lines.
What the claim costs in powder
The arithmetic is simple and worth writing down before the fill is chosen. At the theoretical figures, 1 mg of copper needs 3.33 mg of the chelate or 7.14 mg of the gluconate; 2 mg needs 6.67 mg or 14.3 mg; 3 mg needs 10.0 mg or 21.4 mg. The gluconate needs about 2.1 times the mass at every dose.
| Label claim (Cu) | Copper bisglycinate at 30.0% | Copper gluconate at 14.0% | Extra gluconate mass |
|---|---|---|---|
| 1 mg | 3.33 mg | 7.14 mg | 3.81 mg |
| 2 mg | 6.67 mg | 14.3 mg | 7.62 mg |
| 3 mg | 10.0 mg | 21.4 mg | 11.4 mg |
The catalog ranges move the numbers by only a few percent: at 29.0% the chelate needs 3.45 mg for 1 mg of copper, at 31.0% it needs 3.23 mg; at 13.5% the gluconate needs 7.41 mg, at 14.5% it needs 6.90 mg. The gap between materials is far larger than the uncertainty inside either range.
These figures are arithmetic, not a dosing instruction. The label claim belongs to the brand and its reviewer; the specification's job is to make the copper figure used in the calculation match the certificate.
Solubility and the matrix
The catalog describes the chelate as slightly soluble in water, with an acidic solution; the gluconate is freely soluble and gives a blue-green solution. For a stick pack, drink mix or liquid, the gluconate is the easier starting point. For a capsule, tablet or dry blend, the chelate's lower solubility is not a problem; it is a reason to keep the powder dry.
Solubility is not stability. In water the chelate sits in equilibrium with its ligand and the copper ion; a low pH can protonate the glycine and shift the balance, and a higher pH can hydrolyse the copper. Copper is also redox-active, so a wet matrix with a reducing agent or dissolved oxygen needs its own hold-time work.
Do not assume the two behave alike because both are blue. A formula built on the gluconate and switched to the chelate at the same weight will be under-copper and may not dissolve; the reverse switch will be over-copper and may change colour and pH.
What the difference does to the fill
A 2 mg copper claim uses about 6.7 mg of the chelate or 14.3 mg of the gluconate. In a 300–500 mg capsule both are small: the fill is mostly excipient, and the practical problem is uniformity, not capacity. The chelate leaves more room for other actives; the gluconate's larger mass can be easier to weigh at a very low dose.
A premix is the usual answer. The copper source is diluted onto a carrier so that a few milligrams become a weighable portion that blends evenly. The carrier must be declared, and the diluted premix is a different specification with its own copper figure. A tablet needs a compressible premix and a granule that does not segregate.
Capsule size follows the total fill, not the copper line alone. If the formula is tight the chelate can save a size; if other actives dominate the fill, the saving may not be visible.
The label and the switch
The label declares elemental copper and names the source: “copper (as copper bisglycinate)” or “copper (as copper gluconate)”. A switch changes that line, the specification, the certificate, the copper figure and often the fill weight. The salt mass is an internal number; the declared copper is the label number, and both come from the same certificate.
The buyer's regulatory team confirms the form and the wording for the destination. A raw-material page cannot approve a label, and a certificate for one source does not cover the other.
When to choose which
Choose the chelate when the label names copper bisglycinate, the matrix is dry, and the fill benefits from the higher copper figure. Choose the gluconate when the label names it, the matrix is aqueous, and the fill can carry about 7.1 mg of salt per milligram of copper. Choose neither when the label names another copper source.
Switching source changes the specification, the identity test and the label. It should go through change control rather than a substitution at equal weight.
The product hub has the catalog specification; the grades page places this comparison in the wider range; the copper gluconate page is the other side; zinc bisglycinate runs the same chelate arithmetic with a different metal; the methods library covers the assay; the quality page covers release.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation