Minerals & Electrolytes · Core range

Zinc Bisglycinate

Zn(C₂H₄NO₂)₂·H₂O · CAS 14281-83-5 · 1:2 zinc–glycine chelate, monohydrate

A 1:2 zinc–glycine chelate specified at 26.0–28.0% elemental zinc, for capsules, tablets and powder blends where the label names a chelate rather than a zinc salt.

Zinc (Zn)
26.0–28.0%
Minimum order
1 kg
Indicative lead time
1–7 days
Standard packing
1 kg foil pouch25 kg fiber drum

Specification

What the certificate will report

Zinc (Zn)26.0–28.0% (complexometric EDTA)
Glycine59.5–64.5% (HPLC)
Zn : glycine ratio1 : 2 molar (calculated)
Free glycine≤1.0% (HPLC)
AppearanceWhite to off-white crystalline powder
pH (1% suspension)5.0–8.0
Loss on drying≤8.0%
Particle size≥95% through 40 mesh
Bulk density0.40–0.70 g/mL
Heavy metalsPb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg
MicrobiologyAPC ≤1,000 cfu/g · yeast and mould ≤100 cfu/g · E. coli and Salmonella absent
Chemical formulaZn(C₂H₄NO₂)₂·H₂O
CAS14281-83-5
Marker setZinc (26.0–28.0%), glycine (59.5–64.5%), Zn : glycine 1:2
AppearanceWhite to off-white, free-flowing crystalline powder
SolubilitySoluble in water; the 1% suspension is slightly acidic to neutral (pH 5.0–8.0).

Primary method Complexometric EDTA titration and HPLC — the method behind each figure matters as much as the figure. How the COA is built →

What to confirm before ordering

  • Name the hydrate and the zinc figure. A 27% monohydrate and a 20% spray-dried grade are different drums with different fill weights.
  • Ask for the glycine assay and the Zn : glycine ratio, not only the zinc figure; a blend with zinc oxide can pass a zinc assay.
  • Check free glycine and an XRD oxide screen if the label says chelate.
  • Zinc has an EU upper level and labelling requirements; confirm the daily portion with your regulatory team.

Buyer questions

Practical answers

What is Zinc Bisglycinate specified to?

Zinc (Zn): 26.0–28.0% (complexometric EDTA). The full specification adds Glycine, Zn : glycine ratio, Free glycine, Appearance, pH (1% suspension) and the contaminant panel. Every figure on the batch COA is reported with the method used to produce it.

Is Zinc Bisglycinate a chelate or a blend?

The catalog grade is a 1:2 zinc–glycine chelate. Blends with the corresponding oxide or carbonate are a different material and are not supplied under this specification. The identity page explains how the distinction is tested.

Which dosage forms does this grade fit?

Capsules and tablets, Powder sticks and drink mixes, Gummies and chews, Functional beverages. The grade is selected against the dosage form and the target dose: capsule fill and tablet flow depend on bulk density and particle size, while a stick pack or gummy depends on dissolution and taste.

Which documents are supplied with the batch?

A batch-specific COA, TDS, SDS, allergen and GMO statements, an origin record and a residual-solvent statement. Third-party heavy-metal or microbiological reports can be arranged, and the specification comparison is issued before the first order.

What is the minimum order and lead time?

1 kg minimum, packed in a 1 kg foil pouch from a released lot; 25 kg fiber drums are available as quantities scale. 1–7 days after specification and order confirmation. Samples are typically 100–500 g and carry the COA of the lot they were drawn from.

Documentation

Released with every lot

  • Batch-specific certificate of analysis against the agreed specification
  • Technical data sheet with form, CAS or species, carrier, storage and packing
  • Safety data sheet in the 16-section format
  • Allergen, GMO and origin statements signed for the batch
  • Residual-solvent statement for the crystallisation system
  • Specification comparison against the specification you sent

What this page does not claim

Zinc Bisglycinate is sold as an ingredient powder. No therapeutic or disease claim is made here, and no finished dosage form is offered. In the EU, claims for the nutrient or ingredient are restricted to the authorised list; in the US, structure/function statements are the responsibility of the brand that makes them and require substantiation. We publish specification, method, form and documents — that is the boundary of what we write.

Next step

Send the spec. We will confirm the form.

A competitor COA, a label claim or a target dose is enough to start. We reply with the grade we can release, the documents behind it and the questions we still need answered.